Robe Robin iParfect 150 RGBA Robin iParfect 150 FW RGBA User manual

Brand: Robe

Model: Robin iParfect 150 RGBA Robin iParfect 150 FW RGBA

Category: Stroboscopes & disco lights

Type: User manual

Robe Robin iParfect 150 RGBA Robin iParfect 150 FW RGBA is a professional lighting fixture designed for outdoor use.

Version 1.4

Table of contents

1. Safety instructions ......................................................................................................... 3

2. Fixture exterior view ...................................................................................................... 5

3. Installation....................................................................................................................... 6

3.1 Connection to the mains ............................................................................................ 6

3.2 Installing barndoors and the gel frame ....................................................................... 7

3.4 Rigging the xture ...................................................................................................... 9

3.5 DMX-512 connection ................................................................................................ 11

3.6. Wireless DMX operation ......................................................................................... 12

4. Control menu map ........................................................................................................ 13

5. Control menu (Standard and Easy control mode) ..................................................... 15

5.1 Addressing (DMXA) .................................................................................................. 16

5.2 Fixture information (Info) .......................................................................................... 16

5.3 Personality (Pers) ..................................................................................................... 16

5.4 Manual Control (Manual) .......................................................................................... 17

5.5 Test program (Test Prg) ............................................................................................ 17

5.6 Stand-alone (St Alone) ............................................................................................. 17

5.7 Reset function (Reset) ............................................................................................. 18

5.8 Special functions (Special) ....................................................................................... 18

6. RDM ............................................................................................................................... 20

7. Error and information messages ................................................................................ 21

8. Technical Specications .............................................................................................. 21

9. Maintenance and cleaning ........................................................................................... 23

9.1 Replacing the fuse ................................................................................................... 24

9.2 Disposing of the product .......................................................................................... 24

10. Photometric diagrams................................................................................................ 25

ROBIN iParfect 150 RGBA

ROBIN iParfect 150 FW RGBA

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE POWERING OR INSTALLING YOUR iParfect 150 !

Save it for future reference.

This device has left our premises in absolutely perfect condition. In order to maintain this condition and to en-

sure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning notes

written in this manual.

The manufacturer will not accept liability for any resulting damages caused by the non-observance of this

manual or any unauthorized modication to the device.

Please consider that damages caused by manual modications to the device are not subject to warranty.

The iParfect 150 was designed for outdoor use and it is intended for

professional application only. It is not for household use.

1. Safety instructions

DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT!

Make sure that the available voltage is not higher than stated on the rear panel of the xture.

This xture should be operated only from the type of power source indicated on the marking label. If you are

not sure of the type of power supplied, consult your authorized distributor or local power company.

Always disconnect the xture from AC power before cleaning, removing or installing any part of the xture.

The power plug has to be accessible after installing the xture. Do not overload wall outlets and extension cords

as this can result in re or electric shock.

Do not allow anything to rest on the power cord. Do not locate this xture where the cord may be damaged by

persons walking on it.

Make sure that the power cord is never crimped or damaged by sharp edges. Check the xture and the power

cord from time to time.

Refer servicing to qualied service personnel.

This xture falls under protection class I. Therefore this xture has to be connected to

a mains socket outlet with a protective earthing connection.

Do not connect this xture to a dimmer pack.

Warning!

Risk group 1, RG-1 (for beam angle >10°)

Risk group 2, RG-2 (for beam angle =<10°).

Do not stare at exposed lamp in operation. May be harmful to the eyes.

Avoid looking directly into the light source

LED light emission. Do not view the light output with optical instruments or

any device that may conncentrate the beam.

The light source contains blue LEDs.

Avoid brute force when installing or operating the xture.

When choosing the installation spot, please make sure that the xture is not exposed to extreme heat, or dust.

Do not block the front transparent glass with any object when the xture is under

operation.

Housing of the xture should never be covered with cloth or other materials.

This xture should not be placed in a built-in installation unless proper ventilation is provided.

Only operate the xture after having checked that the housing is rmly closed and all screws are tightly fastened.

Make sure that the area below the installation place is blocked when rigging, derigging or servicing the xture.

To avoid damage of an internal optical system of the xture, never let the sunlight (or

other light source) lights directly to the lens array, even when the xture is not working

The xture becomes very hot during operation. Allow the xture to cool approximately 30 minutes prior to

servicing or maintenance.

Operate the xture only after having familiarized with its functions. Do not permit operation by persons not

qualied for operating the xture. Most damages are the result of unprofessional operation!

Please use the original packaging if the xture is to be transported.

Please consider that unauthorized modications on the xture are forbidden due to safety reasons!

If this device will be operated in any way dierent to the one described in this manual, the product may suer

damages and the guarantee becomes void.

2. Fixture exterior view

5 - Mounting hole for clamp

6 - Attachment point for accessories

7 - DMX OUT (with sealing cover)*

8 - Mains IN (with sealing cover)*

9 - Mains OUT (with sealing cover)*

10 - DMX IN (with sealing cover)*

11 - Display and control buttons

1 - Mounting bracket

2 - Tilt locks

3 - Lens array with transparent

glass cover

4 - Accessory frame adaptor

*IMPORTANT!

Fixture´s power connectors (8, 9) are dust and water protected according to protection class IP 65 by

mating with related power connectors with cords (IP 65 rated) or by covering with the rubber sealing

covers . They cannot stay uncovered outdoor (e.g. during xture installation).

Fixture´s DMX connectors (7, 10) are dust and water protected according to protection class IP 65 by

mating with related power connectors with cords (IP 65 rated) or by covering with the rubber sealing

covers . They cannot stay uncovered outdoor (e.g. during xture installation).

3. Installation

Fixtures must be installed by a Qualied electrician in accordance with

all national and local electrical and construction codes and regulation.

3.1 Connection to the mains

For protection from electric shock, the xture must be earthed!

The iParfect 150 is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz AC

power source from 100-240 Volts.

Install a cord cap on the power cable to allow connection to power outlet, install a grounding-type (earthed)

plug with suitable IP rating , following the plug manufacturer’s instructions.

If you have any doubts about proper installation, consult a qualied electrician.

Core (EU) Core (US) Connection Plug Terminal Marking

Brown Black Live L

Light blue White Neutral N

Yellow/Green Green Earth

This device falls under class one and must be earthed (grounded)!

The max. number of connected xtures in power chain depends on AC mains power voltage:

CE: ETL:

15 xtures at power supply= 230V 9 xtures at power supply= 230V

13 xtures at power supply= 208V 8 xtures at power supply= 208V

7 xtures at power supply= 120V 4 xtures at power supply= 120V

Actual number of xtures may dier from values stated above as you have to take into account the length of

supply cables, circuit breaker etc. at projecting of the xtures installation Do not overload the supply line and

connecting leads.

Wiring and connection work must be carried out by qualied sta!

3.2 Installing barndoors and the gel frame

Disconnect the xture from mains before barndoors and the gel frame installation!

1. Unlock the spring lock (1) of the accessory frame adaptor (2) via pushing this spring lock as show red arrows

on the picture.

2. Insert the gel frame (3) into the bottom slots of the accessory frame adaptor (2).

3. Insert the barndoors (4) into the top slots of the frame adaptor (2).

4. Secure both accessories by moving the spring lock (1) to locked position as shows the red arrow on the picture.

Note: the barndoors can be rotated to desired position and secured in this position via the securing screw (5).

3.4 Rigging the xture

A structure intended for installation of the xture(s) must safely hold weight of the xture(s) placed on it. The

structure has to be certicated to the purpose.

The xture must be installed in accordance with national and local electrical and construction codes and re-

gulation.

For overhead installation, the xture must be always secured with a safety wire.

IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including calculating working

load limits, installation material being used, and periodic safety inspection of all installation material and the

projector. If you lack these qualications, do not attempt the installation yourself, but use a help of professional

companies.

CAUTION: Fixtures may cause severe injuries when crashing down! If you have doubts concerning the safety

of a possible installation, do not install the xture!

The operator has to make sure that safety-relating and machine-technical installations are approved by a skilled

person once a year.

Allow the xture to cool for ten minutes before handling with it.

The xture has to be installed out of the reach of public.

The xture must never be xed swinging freely in the room.

When installing the device, make sure there is no highly inammable

material (decoration articles, etc.) in a distance of min. 0.4 m.

Use an appropriate clamp to rig the xture on the truss.

Make sure that the device is xed properly! Ensure the

structure (truss) to which you are attaching the xtures is secure.

When installing xtures side-by-side, avoid illuminating one xture with another!

The xture can stand on the stage oor ( by means of the unfolded mounting bracket) or rigged on a truss (via

folded mounting bracket) without altering its operation characte ristics.

For securing the xture to the truss, install a safety wire which can hold at least 10 times the weight of the xture.

Use only the safety wire with snap hooks with screw lock gates. Fasten the safety cable around the truss and

the mounting bracket as shown on the picture below.

1-Clamp

2-Truss

3-Mounting bracket

4-Safety wire

3.5 DMX-512 connection

The xture is equipped with 5-pin XLR sockets for DMX input and output. Only use a shielded twisted-pair cable

designed for RS-485 and 5-pin XLR connectors in order to connect the controller with the xture and xtures

each other.

To keep declared IP rating of the xture, all used XLR connectors and cables have to meet IP 65 rating.

If you use a standard DMX controllers, you can connect the DMX output of the controller directly with the DMX

input of the rst xture in the DMX chain. If you wish to connect DMX controller with other XLR outputs, you

need to use adaptor cables.

Building a serial DMX-chain:

Connect the DMX output of the rst xture in the DMX chain with the DMX input of the next xture. Always

connect xture DMX output with the DMX input of the next xture until all xtures are connected. Up to 32

xtures can be interconnected.

Caution: At the last xture, the DMX chain has to be terminated with a terminator. Solder a 120 Ω resistor

between Signal (–) and Signal (+) into a 5-pin XLR-plug and plug it in the DMX output of the last xture.

DMX output DMX input

XLR socket: XLRplug:

1 - Shield

2 - Signal (-)

3 - Signal (+)

4 - Not used

5 - Not used

1 - Shield

2 - Signal (-)

3 - Signal (+)

4 - Not used

5 - Not used

3.6. Wireless DMX operation

The wireless DMX version of the xture is equipped with the Lumen Radio CRMX module and antenna for

receiving DMX signal. CRMX module operates on the 2.4 GHz band.

To link the xture with DMX transmitter.

The xture can be only linked with the transmitter by running a link procedure on DMX transmitter .

After linking , the level of DMX signal ( 0-100 %) is displayed in the menu item “Stat“ (Special -->Vireless -->Stat).

To unlink the xture from DMX transmitter.

The xture can be unlinked from receiver via the menu item “ Unlink“ (Special-->Vireless -->Unlink.).

4. Control menu map

Default settings=Bold print

Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7

DMXA Set DMXA 001-512

DMX Pres Mode 1

Mode 2

Mode 3

Info POn Time Total

Reset

DMX In

Powr 0-255

Dim F 0-255

Hea Temp Current

Highest

High Res

Sw Ver IC-1

IC-2

Pers

DMX Pres Mode 1

Mode 2

Mode 3

DMX In Wired

Wireless

Display Turn

On/O T On, O

Contrast 0-100%

Backlight 0-100%

Col Mix RGBA, CMY

White P On, O

Dimmer C Square, Linear

LED Freq Stand

High

LED Fadj -06,-05..00..05, 06

Temp Uni °C, °F

I Ef Pos Powr

Dimm F

Store

Defaults

Manual Manual C Powr 0-255

Dim F 0-255

Test Prg

Sta Alone

Auto Run O

Test

Prog 1

Prog 3

Pr Play Test Prg

Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7

Prog 1

Prog 3

Pr Edit Prog 1 Step 1 Powr

Prog 2 : :

Prog 3 Step 40 F.Tim 0-25.5

S.Tim 0-25.5

COPY

Prg En 1-40

Reset

Special RDM Low

RDM Hight

Wireless Stat

Unlink

Adjust DMX Val Powr 0-255

Dim F 0-255

Clalib Cal Mech Zoom C 0-255

Store

Cal Col Red C 0-255

Gre C 0-255

Blu C 0-255

Amb C 0-255

Store

Cal Load

Sw Upd On, O

5. Control menu (Standard and Easy control mode)

The iParfect 150 is equipped with 2-row LCD display which allows to set the xture´s behaviour according to

your needs, obtain information on its operation, control all range of eects and program it in stand-alone mode.

The four control buttons have the following functions according to the control mode:

Standard control mode (default setting)

- ESCAPE button used to leave the menu without saving changes.

, - NEXT, PREV buttons for moving between menu items and for value adjusting.

- ENTER button used to enter the selected menu (menu item) and to conrm adjusted value.

After switching the xture on, the display shows set DMX address.

Easy control mode

[INTENSITY] buttons used to set light intensity (dimmer).

[COLOR] buttons used to set colour on the Virtual colour wheel.

After switching the xture on, the display shows dimmer intensity and colour which have been set before

switching the iParfect 150 o.

When the xture is switched o, both adjusted color and light intensity are saved into memory and loaded after

switching the xture on.

Note: DMX control in this mode is disabled.

Switching the xture to Easy control mode

When the current DMX address is displayed in the Standard control mode:

press the [NEXT] and [PREV] buttons at the same time until the screen for the Easy control mode appears.

For switching the xture back to the Standard control mode, press the [NEXT] and [PREV] buttons at the same

time until the screen for the Standard control mode appears.

The following menu items are accessible in the Standard control mode only.

5.1 Addressing (DMXA)

Set DMXA - Use this menu item to set the DMX start address of the xture, which is dened as the rst channel

from which the iParfect 150 will respond to the controller.

If you set, for example, the address 31, the iParfect 150 will use channels 31 - 48 for control (if Mode 1 is

selected).

Please, be sure that you do not have any overlapping channels in order to control each iParfect 150 correctly

and independently from any other xture on the DMX data link.

If there is no data received at the DMX input, the display will start to ash "0001” with actually stored DMX address.

DMX Pres - DMX preset. Use the menu to select desired channel mode.

Mode 1 - 17 control channels (default)

Mode 2 - 11 control channels

Mode 3 - 5 control channels

5.2 Fixture information (Info)

POn Time - Power on time. Select this menu to read the number of xture operation hours.

Total -

The item shows the total number of the operation hours since

the iParfect 150

has been fabricated.

Reset -

The item shows the number of the operation hours that the

iParfect 150

has been powered on since the counter was last reset.

In order to reset this counter to 0, press and hold both [NEXT] and [PREV] buttons and

the [Enter] button at the same time.

DMX In - DMX readout. The menu is used to read DMX values of each channel received by the xture.

Hea. Temp - Temperature. The menu shows temperature of the LED module.

Current - A current temperature of the LED module.

Highest - A maximum temperature of the the LED module since the xture has

been fabricated.

High Res - A maximum temperature of the the LED module since the counter

was last reset.

In order to reset this counter, press and hold both [NEXT] and [PREV] buttons and the

[Enter] button at the same time.

Sw Ver - Software versions. Select this item to read the software version of the xture modules.

IC-1 - A display processor.

IC-2 - A LED control processor.

5.3 Personality (Pers)

DMX Pres - DMX preset. Use the menu to select desired channel mode.

Mode 1 - 17 control channels (default)

Mode 2 - 11 control channels

Mode 3 - 5 control channels

DMX Input- Use the menu to select mode of DMX signal receiving.

Wired - DMX signal is received by means of the standard DMX cable.

Wireless - DMX signal is received by means of the inbuilt wireless module (wireles DMX version only).

Display - Display adjusting. This menu allows you to adjust the display behaviour.

Turn - This function rotates menu 180 degrees from current orientation.

Note: Pressing and holding the Escape button also rotates menu.

On/O T - This function allows you to keep the display permanent on or turn it o two

minutes after last pressing any button on the control panel.

Contrast- Use this function to adjust contrast of the display (0-100%).

Backlight- Use this function to adjust backlight of the display (0-100%).

Col. Mix. - Colour mixing mode. This item allows switching into RGBA or CMY mode. In the CMY mode, the

amber(8bit) and amber (16) bit channels are not active.

White P - White Point 8000K. If the function is on, the CTC channel allows to set desired white in range of

8000K-2700K

(0 DMX=8000K,64 DMX=5600K, 128 DMX=4200K, 192 DMX=3200K, 255 DMX=2700K). Necessary condition

is , that RGBA channels have to be full (255DMX) or set at the same DMX values, e.g. 150 DMX.

If this function is o, the range of whites is not uniform and may be dierent for each xture.

Dimmer C - Dimmer curve. Use the menu to select desired dimmer curve.

Linear - a linear curve.

Square - a square law curve.

LED Freq - LEDs frequency setup. The function allows you to set the PWM (Pulse Width Modulation) output

frequency of LEDs to Standard or High.

Stand - a standard frequency (300Hz).

High - a high frequency (600Hz)

LED Fadj - LEDs frequency ne adjustment. The function allows you to change the selected PWM output

frequency of LEDs in 6 levels up and down around the selected frequency in the menu “LED Freq”.

-06...-01 - Frequence levels 1-6 under selected frequency.

00 - Selected frequency (Standard or High)

01...06 - Frequence levels 1-6 above selected frequency.

Temp Uni - Temperature unit. Use the menu item to change temperature unit from °C to °F.

I Ef Pos - Init eect positions. Use the menu to set all eects to the desired positions at which they will stay

after switching the xture on without DMX signal connected.

Defaults - The menu item allows to set all xture parameters to the default (factory) values.

5.4 Manual Control (Manual)

Use the menu to control all xture channels by means of the control panel.

5.5 Test program (Test Prg)

Use this menu to to run a special demo-test sequences without an external controller, which will show you some

possibilities of using the iParfect 150.

5.6 Stand-alone (St Alone)

The iParfect 150 oers three user-editable programs (Prog 1-Prog 3), each up to 40 steps. T

Auto Run - Presetting playback. This function allows you to select the program which will be played in

the stand-alone mode after switching the xture on. Selected program will be played continuously in a loop.

O - The option disables „Auto Run” function.

Test, Prog 1, Prog 2, Prog 3 - Selected program will start running after switching

the xture on.

Pr Play - Playing program. Select this menu to run a desired program in a loop (Test Prg, Prog 1 - Prog 3).

Select the program you wish to run and press the [ENTER]. The selected program

will start running. By Pressing the [ENTER] again, the program pauses running.

Pr Edit - Editing program. Select this menu to edit or create three editable programs (Prog 1-Prog 3). Each

program step has a step time - during which eects last in the current step and a fade time- during which eects

move to new positions.

To edit program.

1. Press [NEXT] or [PREV] to select the menu "Pr Edit" and press [ENTER].

2. Press [NEXT] or [PREV] to select the desired program and press [ENTER] button.

3. Press [NEXT] or [PREV] to select the desired program step and press [ENTER] button.

4. Press [NEXT] or [PREV] to select the desired item and press [ENTER] button. Now you can edit by [NEXT]

or [PREV] buttons the DMX value (0-255) for selected item:

Prg En.

a total number of the program steps (value 1-40). This value you should be set before

starting of programming

(e.g. if you want to create program with the 10 steps,

set Prg En=10).

Powr power/special functions

Virt C a virtual colour wheel

Red a red LEDs saturation (coarse )

Red F a red LEDs saturation (ne)

Green a green LEDs saturation (coarse)

Green F a green LEDs saturation (ne)

Blue a blue LEDs saturation (coarse)

Blue F a blue LEDs saturation (ne)

Amber an amber LEDs saturation (coarse)

Amber F an amber LEDs saturation (ne)

CTC a colour temperature correction

C Mix C a colour mix control

Zoom a zoom movement (coarse)

Zoom F a zoom movement (ne)

Stro a strobe/shutter function

Dimm a dimmer function coarse

Dim F a dimmer function ne

F.Tim a fade time (0-25.5 sec)

S.TiM a step time (0-25.5 sec)

COPY copying the current prog. step to

the next prog. step

5. Press [ENTER] button to conrm adjusted value .

6. Press [ESCAPE] button, select next prog. step, press [ENTER] button and repeat steps 4 - 5).

5.7 Reset function (Reset)

The function resets a zoom movement. During the zoom reset is light ouput closed.

5.8 Special functions (Special)

RDM Low - This menu item shows the rst part of the RDM identication code.

RDM High - This menu item shows the second part of the RDM identication code.

Wireless - Wireless DMX information. The menu allows to read some information about

Wireless DMX operation

Stat - Wireless status. Use the menu to read wireless DMX status.

Unlink - use this item to unlink xture from wireless DMX.

Adjust - Adjustment. The menu allows the ne adjustment of eects.

DMX Val- DMX values. Use the menu to set DMX values of xture´s channels.

Calib - calibration of white colour.

Cal Mech - Use this menu to calibrate a zoom position.

Cal Col - Use this menu to set white colour 5600K.

Calibration of the zoom position via the control board

1. Disconnect DMX controller from the xture and enter the "Cal Mech" menu.

2. Use the [PREV] and [NEXT] to nd "Zoom C" and press [ENTER].

3. Set desired value and conrm it by pressing [ENTER]..

4. After calibration, nd item "Store" and press [ENTER]. to save all adjusted values and reset the xture.

Calibration of the white 5600K via the control board

1. Disconnect DMX controller from the xture , set the shutter, dimmer and RGBW channels at 255 DMX, zoom

at 128 DMX and the CTC channel at DMX=64 (white 5600K). Aim the light beam on the lux meter (e.g. Minolta

CL-500 A Chroma meter) which is placed roughly 5m from the xture.

2. Set the menu items colour mixing mode "Colour Mix" to RGBA and white point 8000K "White P" to On

(Pers-> Col Mix -> RGBA, Pers-> White P -> On).

3. Enter the menu "Cal Col".

4. By means of the items "Red C, Gre C, Blu C and Amb C" adjust the 5600K colour temperature

as exactly as possible (∆u´v´= 0).

5. After adjusting 5600K colour temperature, select item Store and press the [ENTER] button to save all

adjusted values.

Note: you can also use DMX controler for both calibrations stated above, calibration protocol is the following:

Eect Mode 1 Mode 2 Mode 3

Fine adjustment of zoom position channel 18 channel 12 channel 6

Fine adjustment of red LEDs saturation channel 19 channel 13 channel 7

Fine adjustment of green LEDs saturation channel 20 channel 14 channel 8

Fine adjustment of blue LEDs saturation channel 21 channel 15 channel 9

Fine adjustment of amber LEDs saturation channel 22 channel 16 channel 10

Cal Load - Loads default (factory) calibration.

Sw Upd - Software update. The menu item allows you to update software in the xture.

The following items are required in order to update software:

- PC running Windows or Linux or macOS

- DSU le

- Flash cable RS232/DMX, P/N13050624 (if you want to use a serial port of PC)

- Robe Universal Interface or Robe Universal interface WTX (if you want to use an USB port of PC)

After the software updating the xture will be set to default (factory) values.

To update software in the xture:

1. DSU le is available from Robe web site at WWW.robe.cz.

File with extension zip is intended for Windows (used and tested from XP to W10 on 32/64bit systems).

File with extension tbz is intended for Linux (used and tested on Debian and Ubuntu 32/64bit).

File with extension dmg is intended for

macOS (used and tested on OSX up to Sierra) XQuartz required,

install it from https://www.xquartz.org/

Save the download le to a folder on your computer.

In case that you use windows, extract les in the zip le (e.g. DSU_iParfect150FW_18032267.zip)

2. Disconnect the xture from DMX controller.

3. If you use the ash cable RS232/DMX, connect a serial port of your computer with DMX input of the xture

by means of the cable.

If you use the Robe Universal Interface, connect a USB port of your computer with the Robe Universal Interface

by means of the USB cable and DMX input of the xture with the DMX output of the Robe Universal Interface

via a DMX cable.

4. Switch the xture to the update mode (Special --> SW Upd).

Note: If you do not want to continue in the software update, you have to switch o and on the xture

to escape from the updating mode.

We recommend to cancel all running programs on your computer before starting the software update.

5. Double-click the software uploader le (e.g. DSU_iParfect150FW_18032267.exe) in

the extracted les. The Software Uploader program will start running.

6. Select correct "COM " number if you use a

Flash cable RS232/DMX

or select "

Robe Universal Interface 1 "

if you use the

Robe Universal Interface/Robe Universal Interface WTX

and then click on the "Connect" button.

7. If the connection is OK, click the “Start Uploading" button to start software uploading. It will take several

minutes to perform software update.

If the option "Incremental Update" is not checked, all processors will be updated (including processors with

the same software version).

If you wish to update only processors with new version of software, check the “Incremental Update

box“.

Avoid interrupting the process. Update status is being displayed in the "Info Box" window.

When the update is nished, the line with the text “Fixture is successfully updated“ will appear in

this window.

In case upload process is interrupted (e.g. power loss), the xture stays in “Updating mode” and you will have

to repeat the software update again.

Another way, how to update software in the xtures (especially large installation of xtures) is to use the ROBE

Uploader. It is a software for automatized software update of Robe xtures. It takes advantage of RDM

support).

For more information please see https://www.robe.cz/robe-uploader/.

6. RDM

This xture supports RDM operation. RDM (Remote Device Management) is a bi-directional communications

protocol for use in DMX512 control systems, it is the new open standard for DMX512 device conguration and

status monitoring.

The RDM protocol allows data packets to be inserted into a DMX512 data stream without adversely aecting

existing non-RDM equipment. By using a special „Start Code,“ and by complying with the timing specications

for DMX512, the RDM protocol allows a console or dedicated RDM controller to send commands to and receive

messages from specic moving lights.

RDM allows explicit commands to be sent to a device and responses to be received from it.

The list of commands for the iParfect 150 RGBA (iParfect 150 FW RGBA) is the following.

Parameter ID Discovery command SET command GET command

DISC_UNIQUE_BRANCH *

DISC_MUTE *

DISC_UN_MUTE *

DEVICE_INFO *

SUPPORTED_PARAMETERS *

SOFTWARE_VERSION_LABEL *

DMX_START_ADDRESS * *

IDENTIFY_DEVICE * *

DEVICE_MODEL_DESCRIPTION *

MANUFACTURER_LABEL *

DEVICE_LABEL * *

SENSOR_DEFINITION *

SENSOR_VALUE *

DISPLAY_INVERT * *

DISPLAY_LEVEL * *

DEVICE_RESET *

DMX_PERSONALITY * *

DMX_PERSONALITY_DESCRIPTION *

STATUS_MESSAGES *

STATUS_ID_DESCRIPTION *

DEVICE_HOURS

PARAMETER_DESCRIPTION *

ROBE_DMX_INPUT * *

ROBE_WIRELESS_UNLINK *

RDM model ID for the iParfect 150 FW is 0x00f5.

Page is loading ...

Robe Robin iParfect 150 RGBA Robin iParfect 150 FW RGBA User manual

Brand: Robe

Model: Robin iParfect 150 RGBA Robin iParfect 150 FW RGBA

Category: Stroboscopes & disco lights

Type: User manual

Robe Robin iParfect 150 RGBA Robin iParfect 150 FW RGBA is a professional lighting fixture designed for outdoor use.

Download PDF

report

Robe Robin iParfect 150 RGBA Robin iParfect 150 FW RGBA User manual

Robe Robin iParfect 150 RGBA Robin iParfect 150 FW RGBA User manual

Related papers

Other documents