iON DOCS2GO Owner's manual

Page is loading ...

3

QUICKSTART GUIDE (ENGLISH)

BOX CONTENTS

Check to ensure the following items are included in your packaging:

• DOCS2GO

• Mini-USB cable

• Protective photo sleeve

• Calibration paper

• Cleaning paper

• Cleaning strip

• Quickstart Guide

• Safety & Warranty Information Booklet

MINIMUM SYSTEM REQUIREMENTS

• iPad or iPad 2 with iOS 4.3.5 or later

• An iTunes Store account (for DOCS2GO App download)

• Internet access (for DOCS2GO App download)

SAFETY INFORMATION

• Keep scanner away from water or moisture and dusty areas.

• Never store scanner in hot and very cold areas.

• Only use attachments/accessories specified by the manufacturer.

• No objects filled with liquids, such as vases, should be placed on the scanner.

• Avoid dust contamination when the scanner is not in use.

• When left unused for a long period of time, disconnect the scanner from its

power source (power outlet).

• Avoid environments where the scanner would be exposed to direct sunlight (or

any other source of excessive heat) for long periods of time.

• Protect the scanner from potential liquid spills such as soda, coffee, tea, etc.

• Do not drop the scanner.

• Operate the scanner on a level, stable work surface, free of excessive vibration.

• Do not open the scanner case without consulting a qualified technician. Doing

so risks electrical shock.

• Position the scanner near its power source where it can be easily accessed

when plugged in.

4

FEATURES

1. PAPER GUIDE – This piece adjusts to help guide the paper into the scanner.

2. FEED SLOT – Insert your paper or photo into this slot when scanning.

3. POWER– Press and hold this button for 3-5 seconds to turn the scanner on/off.

4. MINI-USB PORT (rear panel) – Use the included mini-USB cable to connect

this port to a 10W USB power adapter (sold separately)

5. iPad* DOCK – Connect your iPad to this dock to scan your photos or

documents.

6. PAPER EXIT SLOT (rear panel) – Outputs the paper or photo after scanning.

* iPad is a trademark of Apple Inc., registered in the U.S. and other countries.

CHARGING YOUR iPad

1. Connect one end of the mini-USB cable to the

scanner’s USB port, and the other end to the AC

adapter (that came with your iPad) which

connects to the power outlet.

2. Connect iPad to the scanner’s 30-pin port. Your

iPad will now begin charging.

Notes:

•

To properly charge your iPad, you must connect it to

the dock when the scanner is turned off.

• If your iPad does not appear to be charging, make

sure the scanner is off, then disconnect and

reconnect your iPad.

• In case of insufficient battery power, charge your

iPad when the battery level drops to 20% or

less.

2

1

3

4

5

6

5

APP INSTALLATION AND SCANNING

Before you can begin using the DOCS2GO hardware

with your iPad, you must first install the free

DOCS2GO app from the App Store.

1. Power on the DOCS2GO hardware.

2. Connect iPad to the 30-pin port on DOCS2GO hardware.

3. For the dialog box that appears on the iPad, click

‘Yes’ to go to the App Store to download the

DOCS2GO app.

4. Tap 'Install' or 'Install App'.

5. Open DOCS2GO App on iPad.

6. Prepare your image or document for scanning:

• Paper: Place the paper into the FEED SLOT with

the surface to be scanned facing up. Adjust the

PAPER GUIDE so it rests against the edge of the

paper.

• Photo: Place the photo inside the included

protective photo sleeve. Place the photo sleeve

into the FEED SLOT with the sealed end first and

with the surface to be scanned facing up. Adjust

the PAPER GUIDE so it is at the edge of the

sleeve.

7. Press the SCAN button in the app. The photo or

document will be pulled through the scanner. Preview

your scan in the app and then press SAVE to save your

results to your photo library or press CANCEL to re-

scan.

6

CARE INSTRUCTIONS

CLEANING

For the best scanning quality, please follow these

steps to clean the scanner.

Notes:

• Make sure there is no dust or dirt on the cleaning

paper or cleaning strip.

• Do not use any solvent to clean the sensor.

1. Click the top right corner in the DOCS2GO app

to reveal the “cogwheel” (Settings menu).

2. Tap the cogwheel to go into the Settings menu.

3. Insert the supplied cleaning paper into the

scanner's FEED SLOT with the sponge side

facing DOWN and toward you as if you were going to scan it.

4. Press the Clean menu button in the app. On the next screen that appears, press

the Clean button to begin cleaning.

USING THE CLEANING STRIP

1. Power off the scanner.

2. Hold the grip handle of the cleaning

strip with the sponge side facing

DOWN.

3. Insert the cleaning strip firmly into the

exit slot with the fabric side facing

UP.

4. Push the cleaning strip all the way to

the end of the exit slot.

5. Move the cleaning strip from one side to the other slightly a few times, then

remove it.

CALIBRATION

1. Click the top right corner in the DOCS2GO app to

reveal the cogwheel. (Settings menu)

2. Tap the cogwheel to go into the Settings menu.

3. Remove thin plastic layer on both sides the

calibration paper. Insert the calibration paper (with

the printing side facing UP) into the FEED SLOT.

4. Press the Calibrate menu button in the app.

5. Press the Calibrate button to begin the calibration

process.

Page is loading ...

27

SPECIFICATIONS

Minimum System Requirements:

• iPad or iPad 2 with iOS 4.3.5 or later

• An iTunes Store account (for DOCS2GO App download)

• Internet access (for DOCS2GO App download)

Max Scan Size: 8.5” x 14”

Max Scan Resolution: 300 dpi

Sensor Type: Contact Image Sensor

Light Source: LED (R, G, B)

File Type: JPEG

Power: AC: 100-240V~ 0.45A (.45A) 50-60 Hz

DC: 5.1V, 2.1A from the Apple USB

Power Adapter (Not Supplied)

Power Consumption: 10.5W (Maximum); 5V, 2.1A

Dimensions (W x H x D): 12.1" x 4.4" x 2.8"

(308mm x 111mm x 72mm)

Weight: 1.44Ibs (0.65kg)

Page is loading ...

www.ionaudio.com

MANUAL VERSION 1.7

82-352-10150

iON DOCS2GO, DOCS 2 GO Owner's manual

Related papers

Other documents