Posiflex Polaris ID-160 Series User manual

Brand: Posiflex

Model: Polaris ID-160 Series

Type: User manual

This manual is also suitable for

Posiflex Polaris ID-160 Series is a lineup of digital signage kiosks designed for commercial use. Its primary function is to display digital content such as videos, images, and interactive applications. The series features three models: ID-160, ID-215, and ID-320, which differ in screen size and optional features.

All models come equipped with an Intel Bay Trail J1900 CPU, 8GB of DDR3L memory, and a 2.5-inch SATA SSD storage device. They support various operating systems including POSReady 7 64-bit, Windows Embedded 8.1 Industry 64-bit, and Windows 10 IoT 32/64-bit. The kiosks feature a sturdy metal construction and a sleek design that makes them suitable for a wide range of indoor environments.

ID-160

ID-160P

ID-215

ID-215P

ID-320

ID-320P

Package Contents

 ID-160(P)/215(P)/320(P) digital signage kiosk Unit.………………....(x1)

 Base plate (only for ID-320(P))…...…….…………………………….(x1)

 User manual………………………………………………….………..(x1)

 #5/16-18 screw nuts (only for ID-320(P))…...….…………………….(x5)

 Plan washer (only for ID-320(P))……....……………………………..(x5)

ID-160(P)/215(P)/320(P)

Kiosk

User Manual

18960903020 Ver. B0

http://www.posiflex.com

SOME IMPORTANT NOTES

FCC NOTES

This system meets industry & government requirements and applicable standards.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions manual, may cause

interference to radio communications. It has been tested and found to comply with

limits for a Class A digital device pursuant to subpart B of Part 15 of FCC Rules,

which are designed to provide reasonable protection against interference when

operated in a commercial environment. Operation of this equipment in a residential

area is likely to cause interference in which case the user at his own expense will

be required to take whatever measures to correct the interference.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CE CLASS A WARNING

This equipment is compliant with Class A of CISPR 32. In a residential

environment this equipment may cause radio interference.

AVERTISSEMENT CE CLASSE A

Cet équipement est conforme à la classe A de CISPR 32. Dans un environnement

résidentiel, cet équipement peut provoquer des interférences radio.

WARRANTY LIMITS

Warranty will terminate automatically when the machine is opened by any person

other than the authorized technicians. The user should consult his/her dealer for the

problem happening. Warranty voids if the user does not follow the instructions in

application of this merchandise. The manufacturer is by no means responsible for

any damage or hazard caused by improper application.

LIMITES DE GARANTIE

La garantie prend fin automatiquement lorsque la machine est ouverte par une

personne autre que les techniciens autorisés. L'utilisateur doit consulter son

revendeur pour le problème qui se produit. La garantie s'annule si l'utilisateur ne

suit pas les instructions d'application de cette marchandise. Le fabricant n'est en

aucun cas responsable de tout dommage ou danger causé par une mauvaise

application.

警告使用者

這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，在這

種情況下，使用者會被要求採取某些適當的對策。

SAFETY INSTRUCTIONS

This equipment is not suitable for use in locations where children are likely to be

present.

CONSIGNES DE SÉCURITÉ

Cet équipement ne convient pas à une utilisation dans des lieux pouvant accueillir

des enfants.

BATTERY CAUTION NOTES

 Dispose of used batteries according to the instructions.

 Replacement of a battery with an incorrect type that can defeat a safeguard

(for example, in the case of some lithium battery types)

 Disposal of a battery into fire or a hot oven, or mechanically crushing or

cutting of a battery that can result in an explosion.

 Leaving a battery in an extremely high temperature surrounding

environment that can result in an explosion or the leakage of flammable

liquid or gas.

 A battery subjected to extremely low air pressure that may result in an

explosion or the leakage of flammable liquid or gas.

BATTERIE ATTENTION NOTES

 Jetez les piles usagées conformément aux instructions.

 Remplacement d'une batterie avec un type incorrect qui peut annuler une

sauvegarde (par exemple, dans le cas de certains types de batterie au

lithium)

 Mise au rebut d'une batterie dans le feu ou dans un four chaud, ou

écrasement ou coupure mécanique d'une batterie pouvant entraîner une

explosion.

 Laisser une batterie dans un environnement environnant à des températures

extrêmement élevées pouvant entraîner une explosion ou la fuite de liquide

ou de gaz inflammable.

 Une batterie soumise à une pression atmosphérique extrêmement basse

pouvant provoquer une explosion ou une fuite de liquide ou de gaz

inflammable.

警告

本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之電

池。

Overview

ID-160(P)

ID-215(P)

15.6”

LCD Panel

I/O Cover Plate

Cable Exit

21.5” LCD

Panel

Cable Exit

I/O Cover

Plate

ID-320(P)

View of I/O Interface of ID-160(P)/215(P)/320(P)

32” LCD Panel

Cable Exit

I/O Cover Plate

Base Plate

LAN Port

USB 2.0 Port

USB 3.0 Port

VGA Port

RJ50 COM Port

Audio Port

DC-IN Power Jack

Installing the Main Unit on the Base Plate

(Only for ID-320(P))

1. Unscrew the two #6/32-50L hex socket head screws on the rear side of the

kiosk like the below picture. In the same time please make one hand (or

the other person) hold on the front cover from the other side in case the

front cover will fall down.

2. Then gently remove the front cover. Please refer to the pictures.

I/O cover plate

3. Place the main unit horizontally on the PE foam and then align the base

plate. Make sure the five screw columns of the base plate are aligning with

the five screw holes of the main unit.

4. Put the five washers into the five screw columns.

5. Fix the main unit to the base plate with five #5/16-18 screw nuts.

Connecting Power Adapter and I/O Cables

To have the kiosk ready for operation, please connect the connector of power

adapter and all of the connectors of required I/O cables respectively to the

12VDC-IN power jack and appropriate I/O ports. Please make sure that each

of the cables is fully connected to each of the correct ports. Damages due to

incorrect connection or orientation are not covered by product warranty!

Some cable connectors like the connectors of the COM or LAN cables have to

be gently inserted until a click is heard. It is recommended that the I/O ports,

such as VGA port, should be screwed after the I/O cable connectors are

completely connected. And please make sure that each connector has to be

connected to the right peripheral device in the right way.

CAUTION: On doing insertion or extraction of a cable connector, please

always hold the connector head itself instead of pulling the cable wire.

Doing this could damage the cables and ports, which is considered as an

artificial damage and is not covered by the warranty. The means of power

cord should be connected to a socket-outlet with earthing connection.

ATTENTION: Lors de l'insertion ou de l'extraction d'un connecteur de

câble, veuillez toujours tenir la tête du connecteur elle-même au lieu de

tirer le fil du câble. Cela pourrait endommager les câbles, ce qui est

considéré comme un dommage artificiel et n'est pas couvert par la

garantie. Le cordon d'alimentation doit être connecté à une prise de

courant avec mise à la terre.

To connect the I/O cables, you should carefully remove the I/O cover plate.

Please follow the below steps to remove the I/O cover plate.

ID-160(P)

1. Remove the I/O cover plate by unscrewing the lower #6/32-10L hex

socket head screw on the rear side of the kiosk like the picture below.

2. Then loosen the upper #6/32-10L hex socket head screw on the rear side

of the kiosk like the picture below, and don’t remove the screw.

3. Lift the I/O cover plate up and then remove the I/O cover plate.

ID-215(P)

1. Remove the I/O cover plate by loosening the two #8/32-10L hex socket

head screw on the rear side of the kiosk like the picture below, and don’t

remove the screw.

2. Lift the I/O cover plate up and then remove the I/O cover plate.

ID-320(P)

1. Remove the I/O cover plate by unscrewing the two #8/32-10L hex socket

head screws on the rear side of the kiosk like the picture.

2. Loosen the upper two #8/32-10L hex socket head screws like the pictures.

Don’t remove the screws.

3. Lift the I/O cover plate up and then remove the I/O cover plate.

Opening the Front Cover (Only for ID-320(P))

1. Unscrew the two #6/32-50L hex socket head screws on the rear side of the

kiosk like the below picture. In the same time please make one hand (or

the other person) hold on the front cover from the other side.

I/O cover plate

2. Then gently remove the front cover. Please refer to the pictures.

3. You can drive the power cable, LAN cable, or other cable that you need

down from the LCD monitor to the cable exit at the lower portion of the

kiosk.

You are highly advised not to disassemble or reassemble the kiosk without

professional instructions. Not only might the careless handling during

installation cause irreversible damage to your machine, but also the

improper installation likely leads to system malfunction or failure.

For further installation, please contact the service team of Posiflex for

technical support.

Cable Exit

Specifications

ID-160(P)/215(P)/320(P)

System

CPU

Intel Bay Trail J1900 CPU

System Memory

1 x SO-DIMM socket, 8GB DDR3L max.

Storage Device

SATA socket x 1 (2.5” SSD)

OS Support

POSReady 7 64-bit, Windows Embedded 8.1 Industry 64-bit,

Windows 10 IoT 32/64-bit

Touch Screen

ID-160/215/320: N/A (with a glass cover)

ID-160P/215P/320P: P-CAP Touch Screen

LCD Panel

15.6” 1920 x 1080 FHD LCD panel for ID-160

21.5” 1920 x 1080 FHD LCD panel for ID-215

32” 1920 x 1080 FHD LCD panel for ID-320

Power Source

12V/40W power adapter for ID-160(P)

12V/60W power adapter for ID-215(P)

12V/84W power adapter for ID-320(P)

I/O Connectors

Serial Port

2 x RJ50 serial port

Standard USB Port

6 ports, USB 2.0 x 5 + USB 3.0 x 1

LAN Port

1 x 10/100/1000 Mb

Display Port

1 x VGA

Audio

1 x Audio-out + Mic-in combo jack

DC-IN Jack

1 x 12V DC jack (4-pin)

Power Button

1 x power button

Expansion

Expansion Slot

1 x M.2 socket, WiFi 802.11 ac/b/g/n + BT

Physical Dimension

Dimension

(W x D x H in mm)

253 x 261 x 520 for ID-160(P)

543 x 84 x 334 for ID-215(P)

712 x 475 x 1721 for ID-320(P)

Environmental

Operating Condition

0°C - 40°C, 20%RH - 90%RH

Storage Condition

-15°C - 60°C, 10%RH - 90%RH

Optional Item

Wireless COMM

4G LTE dongle, WiFi/BT module

※

The product information and specifications are subject to change without

prior notice. To get the detailed information on the ID-160(P)/215(P)/320(P),

please check this model from Posiflex Global Website, or contact our service

team for technical support.

<MEMO>

Posiflex Polaris ID-160 Series User manual

Brand: Posiflex

Model: Polaris ID-160 Series

Type: User manual

This manual is also suitable for

Download PDF

report

in other languages

français: Posiflex Polaris ID-160 Series Manuel utilisateur

Posiflex Polaris ID-160 Series User manual

This manual is also suitable for

Posiflex Polaris ID-160 Series User manual

in other languages

Related papers

Other documents