Vivo STAND-V103F Assembly Instructions

Brand: Vivo

Model: STAND-V103F

Type: Assembly Instructions

Triple Monitor Desk Stand

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-v103f

SKU: STAND-V103F

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

PACKAGE CONTENTS

WARNING!

A (x1)

Pole

B (x1)

Weighted Base

C (x1)

Decorative

Cover

P1 (x2)

VESA Plate

(side)

M (x2)

Spare Plastic

Cover

O (x1)

Wrench

I (x2)

M8x10 Bolt

K (x12)

M4x30 Bolt

L (x12)

M4 Spacer

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

J (x12)

M4x12

Thumbscrew

D1 (x1)

Monitor Arm

(center)

D2 (x2)

Monitor Arm

E (x4)

Monitor Arm

Cover

F (x4)

Plastic Pad

G (x2)

M10x47 Bolt

H (x3)

M6x29 Bolt

N (x1)

Allen Wrench

Set

P2 (x1)

VESA Plate

(center)

Q1 (x2)

Security Nut

Q2 (x1)

M4x6 Bolt

R (x4)

Wire Clip

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD

OR BACKWARD.

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

ASSEMBLY STEPS

STEP 1

TOOLS NEEDED

Phillips

Screwdriver

Install the pole (A) to the weighted base (B) using M6x29 bolts (H).

Tighten with a Phillips screwdriver and install decorative cover (C).

22 lbs

(10 kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

PER ARM

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

Assemble the monitor arms (D1, D2) by placing plastic pads (F) on the top and bottom of arms (D2)

and inserting them into the center arm (D1) as shown in the diagram. Secure with M10x47 Bolts (G)

and tighten with the large Allen wrench (N). Press monitor arm covers (E) onto the top and bottom of

arm joints.

STEP 3

Carefully slide assembled monitor arm down onto the

pole, making sure holes for wire clips are facing down, and

secure with M8x10 bolts (I) using the medium Allen wrench

(N). Attach the wire clips (R) to the monitor arm.

STEP 2

2.1

2.2

2.3

STEP 4

OPTION A: Flat Back Monitor

Attach the VESA plates (P1, P2) to the monitors

using M4x12 thumb bolts (J).

NOTE: Hand tighten screws to avoid stripping the

plastic screw heads.

OPTION B: Curved Back Monitor

Attach the VESA plates (P1, P2) to the monitors

using M4 spacers (L) and M4x30 bolts (K). Tighten

with a Phillips screwdriver.

STEP 5A

Slide the center monitor onto the head of monitor arm. Secure with the M4x6 bolt (Q2) and tighten

with a Phillips screwdriver.

d1,d2

STEP 6

Pry o the plastic cover and tighten the nut on the side of the tilt joint with the wrench (O) to fix the

tilt angle of side monitors. Tighten the grub screw on the back of center monitor joint using the small

Allen wrench (N) to fix tilt angle of center monitor.

STEP 5B

Slide the side monitors onto the heads of monitor arm and install the security nuts (Q1). Make sure

the security nuts are installed before you rotate the monitors.

grub

screw

Fix the tilt angle

d1,d2

STEP 7

STEP 8

Pry o the plastic cover and use the large Allen wrench (N) to adjust swivel joints if needed.

To adjust center monitor height, turn the screw behind center monitor joint using the medium Allen

wrench (N). To level the side monitors, remove the security nut and turn the bolt with the small Allen

wrench (N) to raise or lower the monitor. Replace nut aer the adjustment.

STEP 9

Manage cables using the wire clips (R). Remove the split cap from the pole and feed cables through,

pulling ends out from the opening in back. Replace the split cap when finished.

LAST UPDATED: 03/05/2020

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

[email protected]

AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303

Vivo STAND-V103F Assembly Instructions

Vivo STAND-V103F Assembly Instructions

Vivo STAND-V103F Assembly Instructions

Related papers

Other documents