Furuno RC1825DF User manual

FURUNO USA

A3 GMDSS CONSOLE

DEALERS MANUAL

MODEL: RC18xx Series

These Instructions are intended for

Furuno authorized Agents and Dealers ONLY!

These Instructions should not be released to the

operator or owner of the equipment.

TABLE OF CONTENTS

i

This manual contains procedures for changing system settings in the GMDSS

console.

This information is intended for Dealer use only and should not be left with

the console.

1. Felcom 18 .............................................................. 1

2. FM-8900 ................................................................ 2

3. FS-1575/FS-2575 .................................................. 4

4. IB-585 ................................................................... 6

Dealers Manual

1

1.1 Felcom 18

1.1.1 General

These materials are provided to allow an authorized Furuno dealer to

change the IMN.

1.1.2 IMN

1) Press the [F8] key, to enter the Setup menu.

2) Press the [1] key to select the System Setup.

3) Select IMN.

4) While pressing the [ALT] key, type in [I], [M], [N].

5) Now enter the IMN and press the [Enter] key.

6) Press the [Esc] key, then press the [Enter] key.

1.1.3 External Equipment

(Refer to Pg. 3-2 of the Installation Manual, Felcom 18)

This procedure will allow adding additional remote boxes.

1) Press the [F8] key, then the [1] key, to show the System Setup menu.

2) Using the down arrow key, select Command Window and press the [Enter] key.

3) At the Enter Job No.: prompt, enter FURUNOSERVICE, and press

the [Enter] key.

4) At the PASSWORD: prompt, enter FELCOM18, and press the [Enter] key.

5) To show the Remote Box Setup menu, press the [1] key, then the [Enter] key.

6) Press the number key for the equipment that is not connected. In a standard

installation, you would change numbers 1 through 5 to OFF.

7) Select [1] for ON or [2] for OFF and press the [Enter] key.

8) When completed, press the [E] key to Exit. Then press the [Esc] key until

you return to the system status screen.

Dealers Manual

2

2.1 FM-8900

2.1.1 General

These materials are provided to allow an authorized Furuno Agent or Dealer to

change the MMSI and System Settings.

2.1.2 MMSI Settings

1) Before powering the unit on, install the Protection Key (RC1-800-044) or

a jumper between Pins 6 and 23 of the [Junction] port.

2) Turn on the unit and it will open to the INITILIZE SETUP.

3) Enter the password, 652111, then press the [ENT] key.

4) Select MMSI and press the [CHANNEL/ENTER] key.

5) Now enter the ship’s MMSI and press the [CHANNEL/ENTER] key.

If the MMSI needs to be changed, select CLEAR, then press the

[CHANNEL/ENTER] key. Now return to step 4, to reenter the MMSI.

6) Press [CANCEL], once to exit, then remove the Protection Key and cycle power.

Key Lock icon

Key Unlock icon

Dealers Manual

3

2.1 FM-8900 (Continued)

2.1.3 General Menu Settings

This section includes protected operational settings. For other settings

refer to the Operators and Service Manuals, FM-8900.

Unlike past units, most Menu settings are available by pressing the Menu key.

The Service menu for technical settings is accessed in the following manner:

1) To access the SERVICE menu, press the [MENU] key. Then press the [TAB]

Key 5 times. Now select SERVICE and press the [ENTER] key.

2) Now enter the password, [652111]. This will allow access to the SERVICE menu.

Dealers Manual

4

3.1 FS-1575/FS-2575

3.1.1 MMSI

This procedure will allow changing the MMSI.

This should performed by an authorized Furuno dealer only.

1) Open the Transceiver, power on the unit. Press S1 on the T-IF PCB.

2) Enter the password, 652111.

3) Select CLEAR and press the [ENT] key. Then select Yes and press the [ENTER]

key.

4) Select MMSI and press the [ENTER] key.

5) Now enter the ship’s MMSI and press the [ENTER] key.

6) Cycle Power to the unit to return to the RT screen.

Dealers Manual

5

3.1.2 Service Menu (Continued)

1) Press the [TAB] key 5 times. Then

2) Select Service and press [Enter] knob.

3) Enter the Password, 652111.

4) This will allow access to all Service Menus.

Dealers Manual

6

4.1 IB-585 NBDP Terminal

4.1.1 General

These materials are provided to allow an authorized Furuno dealer to

change the ID and Answerback Codes.

4.1.2 ID Codes

1) Press the [F5] key to enter the Station menu.

2) Press the key to select the ID to be entered:

5: Group ID Entry (4/5 digit)

6: Group ID Entry (9 digit)

7: Select ID Entry (4/5 digit)

8: Select ID Entry (9 digit)

3) Press the [Enter] key.

4) Press the [Caps Lock] key.

5) Key in ID (space) CODE.

6) Enter the new ID and press the [Enter] key to save.

4.1.3 Answerback Code

1) Press the [F5] key to enter the Station menu.

2) Press the [4] key to select Answerback Code Entry.

3) Press the [Enter] key.

4) Press the [Caps Lock] key.

5) Key in ANSWER (space) CODE.

6) Enter the new ID and press the [Enter] key to save.

FURUNO USA

OSE-GMD-40Z

Furuno RC1825DF User manual

This manual is also suitable for

Furuno RC1825DF User manual

Related papers

Other documents