2. BFT
  3. MITTO
MITTO

BFT MITTO Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the BFT MITTO Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • Who should operate the BFT MITTO device?
    What should be avoided during the programming process?
    What is the consequence of not following the programming sequence correctly?
    How to distinguish between older and current Mitto transmitters?
    What is the purpose of pressing the hidden button(s) on the transmitter?
    What does '01' on the LCD screen indicate?
    How to add more transmitters after the first one?
    What should be done if the panel is in a foreign language?
    What is the solution if the receiver is full?
    What to do if the programming process is not followed quickly enough?
    How to handle the inadvertent use of 'Add End' instead of 'Add Start'?
    What to do if the function is wired into Channel 2?
    How to deal with a faulty/damaged transmitter?
Adding or Reloading Mitto’s on Panels with LCD Display
The Control Panel Contains Live 230v Contacts That Could Cause Severe
Harm or Fatal Injury If Touched
! Because of the presence of live contacts programming should be restricted to
electrically trained and competent personnel
! Do not attempt this process in wet weather
! Only touch the 3 display control buttons.
! If you are in any doubt seek professional help.
The following sequence will add new, or reload existing Mitto transmitters to control panel
receivers equipped with an LCD screen and three control buttons.
• Read the entire sequence through before attempting
• The process steps must be completed in rapid succession without pause
• If at any stage the panel displays the process has failed.
• If you lose your way or become confused, simply leave the panel to time out
(About 15 seconds) and start again.
• Do not at any time “CONFIRM” or “OK”
Mitto 2 & 4 Button Transmitters – “Hidden Button Function”
• Older Mitto’s have a hidden button on the rear
• Current Mitto’s have no hidden button on the rear
On current Mitto’s this function is achieved by pressing the top 2 buttons together
• Check and confirm which model of Mitto you are using before starting
LCD Screen Button Functions;
1. Press the OK button twice
=
2. Press the middle twice
=
3. Press the OK button once
=
Page 1 of 3
Adding or Reloading Mitto’s on Panels with LCD Display
4. Press the OK button once
=
5. Press and hold the hidden buttons) on your transmitter -
- until the display shows - release the hidden button(s)
=
6. Press the button you wish to operate the gate/door with on your new
transmitter
= “01” relates to the number of transmitters installed on the system.
Subsequent transmitters will result in OK 02, OK 03 etc.
7. The display will now return to
8. If more transmitters are to be added repeat from stage 4
9. If you are finished leave the panel to time out (About 15 sec.)
Your added transmitter(s) will not work until the receiver times out
Common Problems;
• The panel is in a foreign language
Follow the language setting guide below
• The receiver is full – only 64 slots are available
Fit an expansion card – seek technical advice
• Process not followed quickly enough – panel has timed out
Repeat the process
• Inadvertent use of Instead of
Repeat the process using Add StArt
• The function you require has been wired into Channel 2
Repeat the process using Add 2ch (Press the middle button once
after step 3)
• The function you require has been wired to a remote receiver
Locate and identify the receiver – seek technical advice
• Faulty/damaged transmitter –
Diagnose by substitution
This guide only covers simple loading of transmitters, many more functions and options
exist, for more details seek professional help from your local BFT installer.
Page 2 of 3
Adding or Reloading Mitto’s on Panels with LCD Display
Page 3 of 3
Set the Panel To English
1. Press the OK button twice
=
2. Press the middle button 3 times
=
3. Press the OK button once
=
4. Press the middle button 3 times
=
5. Press the OK button once
=
Leave the panel to time out (About 15 seconds)
/