Philips DMC810GL Installation guide

Type
Installation guide

Philips DMC810GL is a multipurpose controller designed for professional lighting control applications. It features 12 channels, each capable of handling various load types including incandescent, magnetic with halogen, electronic driver, and DALI loads. The device supports phase control, DSI, and 1-10V dimming protocols, providing flexible control options.

Philips DMC810GL is a multipurpose controller designed for professional lighting control applications. It features 12 channels, each capable of handling various load types including incandescent, magnetic with halogen, electronic driver, and DALI loads. The device supports phase control, DSI, and 1-10V dimming protocols, providing flexible control options.

Multipurpose
Controller
Installation Instructions
Instructions d’installation
Installationsanweisungen
Instrucciones de instalación
Istruzioni per l’installazione
Installatie-instructies
インストー ル 手 順
安装指示
DMC810GL
RJ12
X 4
X 4
X 4
366 mm (14.41 in)
386 mm (15.20 in)
212 mm (8.35 in)
176 mm (6.93 in) 179 mm (7.05 in)
200 mm
(7.87 in)
200 mm
(7.87 in)
30 mm
(1.18 in)
30 mm
(1.18 in)
200 mm
(7.87 in)
200 mm
(7.87 in)
1
40° C (104° F)
0° C (32° F)
90%
IEC Pollution Degree II
Devices must be installed by a
qualied electrician in accordance with
all national and local electrical and
construction codes and regulations.
Les appareils doivent être installés par un
électricien diplômé conformément à tous les
codes et réglementations électriques et de
construction nationaux et locaux.
Die Geräte sind von einem qualizierten Elektriker
in Übereinstimmung mit allen geltenden
Vorschriften zu installieren.
Los dispositivos deben ser instalados por un
electricista calicado y cumpliendo todas las
normas y regulaciones, tanto nacionales como
locales, sobre instalaciones eléctricas y obras.
I dispositivi devono essere installati da un
elettricista qualicato in conformità con le norme
locali e nazionali vigenti in materia di costruzioni
edilizie e installazione di impianti elettrici.
De apparaten moeten worden aangebracht
door een gekwaliceerde elektricien en in
overeenstemming met alle nationale en
plaatselijke elektriciteits- en bouwvoorschriften.
装置付けは、資格の電気技師に依頼
国おび地域の電気び建設にの法令に
従 ってくだ さい 。
根据国家/地区及当地的电气与建筑规范和法规,该设
备必须由有资质的电工进行安装。
.
2
23
C
H
1
L
N
N
C
H
5
2.5 mm2
13+ AWG
C
H
6
L
L
N
N
C
H
2
C
H
3
L
L
N
N
C
H
7
C
H
8
L
L
N
N
BALLAST
OUTPUTS
C
H
4
L
0.6 Nm
5.5 Lb-in
5 mm2
10+ AWG
2.0 Nm
15.7 Lb-in
5 mm2
10+ AWG
0.4 Nm
3.5 Lb-in
DA+ CH9
DA+ CH10
DA+ CH11
DA+ CH12
DA- COM
DA- COM
DA- COM
DA- COM
x4
DALI DSI 1-10 V
4
3
N
L1
10 mm2
6+ AWG
1.4 Nm
12.4 Lb-in
16 mm2
6+ AWG
2.0 Nm
15.7 Lb-in
Load Type CH5 - CH8
General Use
Incandescent
Electronic Driver
Inrush Current
Magnetic with
Halogen
10 A 240 V
5 A 240 V
3 A 240 V
165 A
2 A 240 V DALI
Broad-
cast
DSI
Control Channel RatingsOutput Ratings / Channel (CH)
1-10 V
64/CH
Guaranteed 128 mA,
Maximum 250 mA
Insulation: basic
200
Sink 50 mA / Source 50 mA
64 / CH 200
Driver dependent
CH9 - CH12
Output Ratings/Group
CH1 & CH5 10 A
CH2 & CH6 10 A
CH3 & CH7 10 A
CH4 & CH8 10 A
DMC810GL 40 A
Phase Control Ratings/Channel
CH1 - CH4 Leading Edge
40 A10 A / CH
76
5
µP
AUX/
UL924
+15V
D +
D -
GND
SHIELD
RS-485 DyNet DMX Rx
RJ12
CH1
N
L
N
EN
CH5
CH6
N
N
CH2
CH3
N
N
CH7
CH8
N
N
CH4
DA+ CH9
DA+ CH10
DA+ CH11
DA+ CH12
DA- COM
DA- COM
DA- COM
DA- COM
1
230 V 40 A
±
14%
DALI DSI 1-10 V
DALI DSI 1-10 V
DALI DSI 1-10 V
DALI DSI 1-10 V
12 V 200 mA
11
RS-485 DyNet
10
Apply de-rating for electronic and LED loads.
The manufacturer is not responsible for dimmable lamp selection. Each lamp/dimmer combination must be tested for compatibility prior to installation.
This is a class A product. In a domestic environment this product may cause radio interference, in which case the user may be required to take adequate measures.
Professional dimmers rated > 1000 W are out of scope of EN 61000-3-2.
SHLD
GND
D+
D-
+12 V
AUX/
UL924
RS-485 DyNet
GND AUX/UL924
< 20 m
0.4 Nm
3.5 Lb-in
0.3-2.5 mm2
22-12 AWG 2 A
8 9
AZZ 477 0922 R16
© 2022 Signify Holding. All rights reserved. Specications are subject to
change without notice. No representation or warranty as to the accuracy or
completeness of the information included herein is given and any liability
for any action in reliance thereon is disclaimed. Philips and the Philips
Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other
trademarks are owned by Signify Holding or their respective owners.
www.dynalite.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Philips DMC810GL Installation guide

Type
Installation guide

Philips DMC810GL is a multipurpose controller designed for professional lighting control applications. It features 12 channels, each capable of handling various load types including incandescent, magnetic with halogen, electronic driver, and DALI loads. The device supports phase control, DSI, and 1-10V dimming protocols, providing flexible control options.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI