Philips DTE1210 Installation guide

DTE1210
Philips
Brand
Philips
Model
DTE1210
Type
Installation guide

Philips DTE1210 is a trailing edge dimmer controller designed to control various lighting loads including incandescent, halogen, dimmable CFL, and dimmable LED. It offers precise dimming control and is suitable for residential, commercial, and industrial applications. The device features 12 channels, each capable of handling a maximum load of 10A, providing a total load capacity of 120A. Advanced features include adjustable minimum dimming level, soft-start, and fade-out functions, making it an ideal choice for creating dynamic lighting effects.

Philips DTE1210 is a trailing edge dimmer controller designed to control various lighting loads including incandescent, halogen, dimmable CFL, and dimmable LED. It offers precise dimming control and is suitable for residential, commercial, and industrial applications. The device features 12 channels, each capable of handling a maximum load of 10A, providing a total load capacity of 120A. Advanced features include adjustable minimum dimming level, soft-start, and fade-out functions, making it an ideal choice for creating dynamic lighting effects.

Trailing Edge
Dimmer Controller
Installation Instructions
Instructions d’installation
Installationsanweisungen
Instrucciones de instalación
Istruzioni per l’installazione
Installatie-instructies
インストー ル 手 順
安装指示
DTE1210
RJ12
X 4
X 4
X 4
206 mm (8.11 in)
286 mm (11.25 in)
600 mm (23.62 in)
620 mm (24.40 in)
202 mm (7.95 in)
200 mm
(7.87 in)
200 mm
(7.87 in)
200 mm
(7.87 in)
200 mm
(7.87 in)
30 mm
(1.18 in)
30 mm
(1.18 in)
1
40° C (104° F)
0° C (32° F)
≤
90%
IEC Pollution Degree II
Devices must be installed by a
qualied electrician in accordance with
all national and local electrical and
construction codes and regulations.
Les appareils doivent être installés par un
électricien diplômé conformément à tous les
codes et réglementations électriques et de
construction nationaux et locaux.
Die Geräte sind von einem qualizierten Elektriker
in Übereinstimmung mit allen geltenden
Vorschriften zu installieren.
Los dispositivos deben ser instalados por un
electricista calicado y cumpliendo todas las
normas y regulaciones, tanto nacionales como
locales, sobre instalaciones eléctricas y obras.
I dispositivi devono essere installati da un
elettricista qualicato in conformità con le norme
locali e nazionali vigenti in materia di costruzioni
edilizie e installazione di impianti elettrici.
De apparaten moeten worden aangebracht
door een gekwaliceerde elektricien en in
overeenstemming met alle nationale en
plaatselijke elektriciteits- en bouwvoorschriften.
装置を取り付ける際は、資格のある電気技師に依頼し、
国および地域の電気および建設に関するすべての法令に
従 ってくだ さい 。
根据国家/地区及当地的电气与建筑规范和法规，该设
备必须由有资质的电工进行安装。
.
2
24
3
N
L
≤ 120 A≤ 10 A/CH
CH1
CH2
CH3
CH4
CH5
CH6
CH7
CH8
CH9
CH10
CH11
CH12
≤ 5 mm2
10+ AWG
2.0 Nm
17.7 Lb-in
≤ 16 mm2
6+ AWG
1.5 Nm
13.3 Lb-in
3
NL1
CH1 N CH2 N CH3 N CH4 N CH5 N CH6 N CH7 N CH8 N CH9 N CH10 N CH11 N CH12 N
L2 L3 E
µP
AUX/
UL924
+12 V
D +
D -
GND
SHIELD
D +
D -
+
-
2 x RJ12
RS-485
DyNet
DMX Rx
DMX
Rx
12 V 1 A
1 230 V ± 14% 63 A =
3 230/400 V ± 14% 3 x 40 A
12 V 200 mA
SELV/Class 2 (UL)
backup power
µP
5
6 A 6 B
IEC Overvoltage Category III
L3
N
L2
L1
1
≤ 16 mm2
6+ AWG
1.4 Nm
12.4 Lb-in
2.0 Nm
17.7 Lb-in
≤ 16 mm2
6+ AWG
L3
N
L2
L1
3
≤ 16 mm2
6+ AWG
1.4 Nm
12.4 Lb-in
≤ 16 mm2
6+ AWG
2.0 Nm
17.7 Lb-in
RS-485 DyNet
+12V
+12V
D-
D+
GND
GND
GND
GND
D+
D–
+12V
+12V
1
2
3
4
5
6
7 B
9
RS-485 DyNet
8
0.4 Nm
3.5 Lb-in
0.3-2.5 mm2
22-12 AWG
GND AUX/UL924
<20 m
RS-485 DyNet
SHLD
GND
D+
D-
+12 V
AUX/UL924
≤ 2 A
7 A
Apply de-rating for electronic and LED loads.
Not compatible with magnetic transformers.
The manufacturer is not responsible for dimmable lamp selection. Each lamp/dimmer combination must be tested for compatibility prior to installation.
Professional dimmers rated > 1000 W are out of scope of EN 61000-3-2.
AZZ 422 0922 R16
© 2022 Signify Holding. All rights reserved. Specications are subject to
change without notice. No representation or warranty as to the accuracy or
completeness of the information included herein is given and any liability
for any action in reliance thereon is disclaimed. Philips and the Philips
Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other
trademarks are owned by Signify Holding or their respective owners.
www.dynalite.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Philips DTE1210 Installation guide

DTE1210
Philips
Brand
Philips
Model
DTE1210
Type
Installation guide

Philips DTE1210 is a trailing edge dimmer controller designed to control various lighting loads including incandescent, halogen, dimmable CFL, and dimmable LED. It offers precise dimming control and is suitable for residential, commercial, and industrial applications. The device features 12 channels, each capable of handling a maximum load of 10A, providing a total load capacity of 120A. Advanced features include adjustable minimum dimming level, soft-start, and fade-out functions, making it an ideal choice for creating dynamic lighting effects.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents