32” Tower fan with remote control
INSTRUCTION MANUAL
Please READ and RETAIN for future reference.
PARTS NAME
1. Remote Control 2. LED Display
3.Rear cover 4. Air outlet grille
5. Base 6. Switch panel
Remote control
MODE function/POWER/TIMER/Oscillation/SPEED
SAFETY ADVICE
Before using this product, please read the instructions carefully
and follow the safety operating rules.
Please keep the warranty certificate and sales receipt. If possible,
please put the package and instructions in a safe place for future
reference.
This product is not suitable for children under 8 years old and
those with weak physical, sensory and intellectual abilities or
lack of experience and knowledge. Unless they have been
supervised or instructed about the safe application of the
product and its risks.
Children should not play with this product. The product shall not
be cleaned and maintained unless the child reaches the age of
August and receives supervision.
Do not allow children under 8 years of age or irresponsible
people to leave their products and power lines unattended,
especially when the product is still on the wall or cooling down.
Check that your power supply is consistent with the display on
the device. Do not leave equipment unattended during use
Always check whether the equipment is damaged. If there is any
sign of damage to the wire or product, do not use it. In this case,
it should be repaired by qualified electricians. If the wire is
damaged, it must be replaced by qualified electricians to avoid
danger. This equipment can only be used in the manner
indicated in this instruction.
Do not immerse the equipment in water or any other liquid, and
avoid splashing on the equipment. Do not use this equipment
near high temperature. Do not hang the power cord on the edge
of the sharp edge of the table or touch the surface of the high
temperature.
Do not use equipment with extension lines.
When the equipment is not used, cleaned or replaced, please
turn off the equipment and remove the power plug from the
power supply.
Do not use the appliance outdoors and place it in a dry
environment.
Do not use accessories that are not recommended by the
manufacturer. They may pose a risk to users and damage
electrical appliances.
Never pull or move electrical appliances to ensure that the wires
are not entangled in any way. Don't wind the wire around the
appliance or bend it.
Before installing the base or any other parts or dismantling, be
sure to unplug the power cord. Make sure the assembly is
correct before inserting the equipment. Never attempt to start
the device without a protective shield. Before unplugging the
power supply, make sure that the electrical appliance is switched
to the "0" position.
Do not insert fingers, pencils, or anything else into the fence.
Do not touch equipment with wet or wet hands
Always put the equipment on a stable plane. In the process of
using, it is also necessary to ensure that the surface can bear the
weight of the device. Adequate space should be provided for air
circulation. (At least 20 cm)
During use, the equipment should not touch curtains, clothing,
towels or other flammable materials.
Do not use this equipment where curtains may be drawn. If the
equipment is used in an inappropriate manner, it may pose a
danger to the user, in which case the producer is not liable for
any possible damage.
Do not allow equipment to be used for a long time while you are
away. You must turn it off before you leave.
Do not point the device at the patient or the sleeping person.
When cleaning equipment, do not disassemble protective
devices and check "clean area".
Before installing the equipment, make sure it is pulled out. Place
the rear base on the bracket.
Push the power cord through the center of the base and insert it
into the wire box.
Clamp the base tightly and adjust the position of the bracket.
Then tighten the nut and place the equipment on a dry, hard
and horizontal plane.
Remote control
To start the remote control, use the CE2025 battery. Open the
battery compartment cover and insert and cover with +/-
correspondingly.
You can operate the fan through panel control or remote control
at a distance of 10 meters. The following shows which switches
perform which speed and wind functions.
Before any cleaning operation is performed, please disconnect
the power supply line between the equipment and the power
supply.
To remove the dirt from the plastic surface, use a soft wet cloth.
Do not use gasoline, diluent or benzene to clean the equipment.
Use a vacuum cleaner to remove dust from the protective shield
without removing them.
Do not immerse the equipment in water or other liquids.
In off-season storage, it is important to keep the equipment in a
safe and dry place. It is important to protect equipment from
dust. We strongly recommend the use of initial packaging to
store equipment.
In order to protect the environment and protect human health,
waste electrical and electronic equipment should be treated
according to the following specific rules.
Taking into account the impact of the user, as indicated on the
label or package symbol, your equipment should not be treated
as an unclassified urban waste. Users should take it to the
municipal collection point for waste collection according to the
instructions, by recycling, recycling or using other wastes.
FUNCTIONS AND USE
DESCRIPTION OF INSTALLATION STEPS
STEP 1: Unscrew the bottom mounting nut.
STEP 2:The two bases are parallel to each other and the four holes are
stuck in the middle of the power cord and inserted into the
bottom of the product.
STEP 3: Align the two protruding dots at the bottom and put them in
STEP 4:Tighten the bottom mounting nut
STEP 5: Screw the four screws properly to prevent shaking
STEP 6:Put the power cord card slot and install it.
STEP1 STEP 2
STEP3 STEP 4
STEP 5 STEP 6
USING THE TOWER FAN
1. Place the fan on a stable surface and ensure that the grilles for
the supply and removal of the air are unobstructed.
2. Connect the power plug to a suitable outlet.
3. POWER: turn ON the FAN by pressing the “POWER ” button; the
product start to work with a low speed (green led turn on). Turn
OFF the FAN by pressing the “ OFF” button.
4. Select the desired speed pressing the “SPEED” button until the
desired speed LED is lit.
5. Press the “ TIMER” button to set timer from 0.5 hour to 7.5
hours (step 0.5 hour).
6. Pressing the “MODE” button will select either
Normal/Nature/Sleep.
7. Press “ OSC” button to start and stop the oscillation function.
Led light will turn on/off in the control panel.
TECHNICAL DATA
Product: Tower Fan
Model: TF-A03
RATED VOLTAGE: 220-240V
RADTED FREQUENCY: 50Hz
“Implementation of Directive 2012/19/EU on Waste
Electrical and Electronic Equipment (WEEE)”,
pertaining to reduced use of hazardous substances in
electrical and electronic equipment, as well as to waste
disposal”. The symbol of the crossed-out wheelie bin
on the equipment or on its packaging indicates that
the product must be disposed of separately from other
waste at the end of its service life. The user must
therefore take the dismissed equipment to suitable
separate collection centres for electrical and electronic
waste, or return it to the dealer in case they purchase
a new device of equivalent type, at a one-to-one-ratio.
Suitable segregated collection of the equipment for
subsequent recycling, treatment or
environmentally-friendly disposal helps prevent
damage to the environment and to human health, and
encourages the re-use and/or recycling of the
materials that make up the equipment. Abusive
disposal of the product by the user shall result in the
application of administrative fines in accordance with
the laws in force.
/
