Page is loading ...
OPERATING MANUAL
PROCESS INDICATOR
PIC-1101
www.multispanindia.comPage - 1
Technical Specification
1) Display : 4 digit, 7 segment LED display (0.56"inch)
2) Size : 96 X 96 X 65mm
3) Input : 0~10V DC, 4~20 mA DC , 0~20 mA DC,( selectable )
4) Output : 1Relay 1C/O
4-20mA Retransmission &
24V DC Transmitter Supply
5) Scalable range : -999 to 9999 (selectable)
6) Range & Decimal Point selectable. Reverse scaling possible.
7) Power Supply : 100-250V AC,50/60Hz
8) Protection Level :
PIC-1101
96 X 96 X 65 mm
Process Indicator PIC-1101
1 2 3 4
IP-65(Front side) AS per IS/IEC 60529:2001
USER CONFIGURATION
SET
Press key.
1 2 3 4
Process Value
S E T
P A S S
H Y S
m o d e
r t L w
9 9 9 9
0 1 2 3
0 0 1 0
L-a L
r t H I
Press
Press
Press
(Range : -999 to 9999)
(Range : -999 to 9999)
& key to set value
& key to set value
& key to set value
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
(0 to 1000)
H-AL or L-AL selectable
Retransmission Lowoutput
Retransmission Highoutput
SET
Press key
SET
Press key
SET
Press key
SET
SET
SET
Press key
Press key
Press key
d p
L R N G
I n p
0 0 0 0
0 0 0 0
SET
Press key
SET
Press key
SET
Press key
SET
Press key
Input
Decimal Point
Low Range
Select by key
0-10V DC
0-20mA DC
4-20mA DC
0 -1 0 0 -2 0
4 -2 0
Press
& key to set value
Press
& key to set Decimal point
www.multispanindia.com
Page - 2
Page - 3 www.multispanindia.com
Working
1). Do all connection as shown in connection diagram and turn on the instrument.
2). Display indicates process value according to 4-20mA i/p available and according
to decimal point set.
3). The Range Corresponding to 4-20mA is selectable from keypad.
4). When the input is 4mA then Display will show 0000 and when input is 20mA then display
will show 9999.
5). If you select lower alarm as a mode then initially relay will remain in on condition.
When process value equals (SET+HYST) then relay will turn OFF. Relay will again
turn ON at (SET POINT) and this on off action continues as process value varies.
6). If you select Higher alarm then initially relay will be in off condition. When
Process value touches (SET) value relay will turn on and relay will turn off at
(SET-HYST) and this cycle continues as process value varies.
7). If the input is not connected Display will show OPEN.
8). When The Input Exceeds the full scale Range (Approx above 20mA) Display will show
OVER.
9). In retransmission mode when parameter RTLW is 0000 then output will be 4mA & when
Parameter RTHIis 9999 then output will be 20mA
f L T R
O F S T
C R F C
S L L
0 0 0 0
0 0 0 0
0 0 0 0
A 0. 0
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Press key Press
& key to set value between 0.0 to 5.0
(ampere range : 0-5mA)
Press ENT key for
save & exit
Filter time
Off-set
Correction Factor
+
-
(range: 100 counts)
(range: 1 sec to 10 sec)
+
-
(range: 999 counts)
Signal Low Level
only for 4-20mA
Press
& key to set value
Press
& key to set value
Press
& key to set value
(Range : -999 to 9999)
H r n g
0 0 0 0
SET
Press key
SET
Press key
High Range
Press
& key to set value
www.multispanindia.com
Page - 4
Product improvement and upgrade is a constant procedure. So for more updated operating information and Support,
Please contact our helpline: 9978991474/75 or Email at marke[email protected]
Connection Diagram
O/P
24V DC
(Trans.)
+
-
O/P I/P I/P
4 To 20mA DC
(Retransmission)
0/4-20
mA DC
0-10V
DC
+ + +
--
20 19 18 17 14 13 12 11
16 15
LN
Range: -999 To 9999 SELE.
Input: 0-10V DC,4-20mA DC,0-20mA DC
Output: 1R1C/O & 4 To 20mA DC Retrans.
& 24V DC (Trans.)
NCCNO
RELAY
7 8 9 10
56
1234
~
50/60 Hz
100
250V AC
Made in India
www.multispanindia.com
/
