SPE GT500 Operating instructions

GT500
Brand
SPE
Model
GT500
Type
Operating instructions

SPE GT500: The Ultimate DCT Cooler Line Kit for Enhanced Transmission Performance

Specifically designed for the 2020+ GT500, the SPE GT500 DCT Cooler Line Kit provides a comprehensive solution to prevent transmission overheating and ensure optimal performance. This kit allows you to upgrade the factory lines with high-quality components, resulting in improved cooling efficiency and leak-free operation.

With its durable construction and precise engineering, the SPE GT500 DCT Cooler Line Kit withstands harsh driving conditions, ensuring long-lasting reliability.

SPE GT500: The Ultimate DCT Cooler Line Kit for Enhanced Transmission Performance

Specifically designed for the 2020+ GT500, the SPE GT500 DCT Cooler Line Kit provides a comprehensive solution to prevent transmission overheating and ensure optimal performance. This kit allows you to upgrade the factory lines with high-quality components, resulting in improved cooling efficiency and leak-free operation.

With its durable construction and precise engineering, the SPE GT500 DCT Cooler Line Kit withstands harsh driving conditions, ensuring long-lasting reliability.

2020+ GT500 DCT Cooler Line Kit
Instructions
1. Lift the car using a hoist or jack and jackstands. Once you have access, remove
the car's belly pan.
2. Remove the 8mm bolts that attach the factory lines to the transmission.
SPE Motorsport ⓒ 2022 1
3. Remove the following mounting bolts.
10mm
15mm
4. Pull upward on the dual metal line strap (after removing the 10mm bolt) to allow the lines
to drop out when removing them. The 15mm nut will not be reused, nor will the bracket.
5. Remove the spring clips at the cooler and midpoint off the lines so they can be removed
in two sections. You should have a total of 4 spring clips, but only 2 will be reused.
SPE Motorsport ⓒ 2022 2
SPE Motorsport ⓒ 2022 3
6. Now that all clips and bolts are removed you can now pull the lines out of the
transmission, then the oil cooler and mid connections. Release the guide clips. Remove
and set the lines aside.
7. Install the seals onto the transmission adapters as shown. Then, install them into the
transmission, matching the from cooler fitting to the from cooler casting on the side of the
case above the fitting bore. Tighten with the original 8mm bolts.
SPE Motorsport ⓒ 2022 4
8. Install the spring clips on to the new cooler quick connect adapters.
9. Remove the rubber/plastic guides and isolators from the old lines. They will be reused at
similar points on the new lines. This will aid in routing and positioning.
SPE Motorsport ⓒ 2022 5
10. Install the quick connect adapters on to the coolers inlet and outlet. Route the first hose
with the straight end from the driver side of the cooler to the transmission fitting closest
to the front of the car, labeled from cooler on the SPE fitting as well as the case. Route
the hose similar to the factory, making sure to go over top of the sway bar. It will go in the
upper position on the metal line clamp.
SPE Motorsport ⓒ 2022 6
11. Route the second hose in a similar fashion, making sure to go over the sway bar.
Connect the 90 degree hose ends to the cooler and transmission.
12. Install the Isolators and line clips similar to factory positions (pictures below). Check
routing and make sure all fittings are snug.
SPE Motorsport ⓒ 2022 7
13. Now that the line kit is installed follow the Ford fill procedure to set the proper fluid level.
TR9070 Fluid Level
1. Using a diagnostic scan tool or the dash gauge, verify the transmission fluid temperature
is less than 120°F (50°C)
2. With the vehicle in NEUTRAL, position it on a hoist or jack stands.
3. Start and run the engine at idle for 3 minutes. Turn off the engine.
NOTE: Make sure that the vehicle is level.
Remove the transmission fluid fill plug.
SPE Motorsport ⓒ 2022 8
4. Using the fluid dispenser, add the transmission fluid through the transmission fluid fill
hole. Fill the transmission until the fluid is level with the fill hole.
USE: Motorcraft® GT500 Dual Clutch Transmission Fluid / XT-14-L or Pentosin FFL4
DCT Fluid.
5. Start and allow the engine to idle for a minimum of 5 minutes or maximum of 10
minutes. Turn off the engine.
NOTE: Make sure that the vehicle is level.
Remove the transmission fluid fill plug.
6. Using a fluid dispenser, add the transmission fluid through the transmission fluid fill
hole. Fill the transmission until the fluid is level with the fill hole.
Material: Motorcraft® GT500 Dual Clutch Transmission Fluid / XT-14-L or Pentosin FFL4
DCT Fluid.
SPE Motorsport ⓒ 2022 9
7.Install the transmission fluid fill plug.
Torque: 133 lb.in (15 Nm)
Now you can reinstall the belly pan and enjoy leak free DCT cooler lines!!
SPE Motorsport ⓒ 2022 10
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

SPE GT500 Operating instructions

GT500
Brand
SPE
Model
GT500
Type
Operating instructions

SPE GT500: The Ultimate DCT Cooler Line Kit for Enhanced Transmission Performance

Specifically designed for the 2020+ GT500, the SPE GT500 DCT Cooler Line Kit provides a comprehensive solution to prevent transmission overheating and ensure optimal performance. This kit allows you to upgrade the factory lines with high-quality components, resulting in improved cooling efficiency and leak-free operation.

With its durable construction and precise engineering, the SPE GT500 DCT Cooler Line Kit withstands harsh driving conditions, ensuring long-lasting reliability.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents