Printronix P7000 H-Series User manual

Programmer’s Reference Manual

KSSM Emulation For The

P7000 H-Series Of Line Matrix Printers

KSSM Emulation For The

P7000 H-Series Of Line Matrix Printers

Programmer’s Reference Manual

Printronix, Inc. makes no representations or warranties of any kind regarding

this material, including, but not limited to, implied warranties of

merchantability and fitness for a particular purpose. Printronix, Inc. shall not

be held responsible for errors contained herein or any omissions from this

material or for any damages, whether direct, indirect, incidental or

consequential, in connection with the furnishing, distribution, performance or

use of this material. The information in this manual is subject to change

without notice.

This document contains proprietary information protected by copyright. No

part of this document may be reproduced, copied, translated or incorporated

in any other material in any form or by any means, whether manual, graphic,

electronic, mechanical or otherwise, without the prior written consent of

Printronix, Inc.

COPYRIGHT

2005, 2007 PRINTRONIX, INC.

Trademark Acknowledgements

Printronix and LinePrinter Plus are registered trademarks of Printronix, Inc.

IBM is a registered trademark of International Business Machines Corp.

Epson is a registered trademark of Seiko Epson Corporation.

Table Of Contents

1 Introduction............................................................. 9

About This Manual....................................................................................9

Warnings And Special Information.....................................................9

Related Product Information ..............................................................9

Software Features ....................................................................................9

2 Configuring With The Control Panel ..................... 11

Introduction .............................................................................................11

Printing The Configuration ......................................................................12

The Configuration Menu .........................................................................15

Moving Within The Configuration Menu ...........................................16

Saving Your New Configuration .......................................................18

LinePrinter Plus Menu......................................................................21

KSSM Emulation ..............................................................................25

3 LinePrinter Plus KSSM Emulation ........................ 27

KSSM Emulation.....................................................................................27

Exceptions And Differences .............................................................27

Default Values And States ...............................................................28

Escape Sequences ..........................................................................29

FS Sequences..................................................................................29

Super-Set Commands......................................................................30

Set And Reset Codes ......................................................................30

Configuring The KSSM Emulation With Control Codes..........................30

Format For Control Code Descriptions.............................................30

Control Code Index .........................................................................31

Advance Print Position Vertically......................................................34

Align SBCS Character with DBCS Character...................................34

Cancel The Alignment of SBCS Character With DBCS Character ..35

Backspace........................................................................................35

Barcode Printing...............................................................................36

Beeper..............................................................................................39

Cancel Line ......................................................................................39

Carriage Return................................................................................39

Define Pattern for Special Printing Effect .........................................40

Define User-Defined Character ........................................................40

Table Of Contents

Define User-Defined Chinese Character.......................................... 41

Delete Last Character in Buffer........................................................41

Divided Hangul Double Height .........................................................42

Enable Printing of Upper Control Codes ..........................................42

Enable Upper Control Codes ...........................................................43

Font Expansion ................................................................................43

Form Feed........................................................................................44

Graphic Printing ...............................................................................44

Graphics Printing: Select Bit Image ................................................. 45

Initialize Printer................................................................................. 45

Line Feed .........................................................................................46

Master Select ...................................................................................47

Master Select In DBCS Mode .......................................................... 48

Master Select One-Line Attribute In DBCS Mode ............................49

Pair Two Characters in Vertical Printing .......................................... 49

Reassign Bit-image Mode ................................................................50

Select 1/6-inch Line Spacing............................................................ 50

Select 1/8-inch Line Spacing............................................................ 50

Select 10 CPI ................................................................................... 51

Select 12 CPI ................................................................................... 51

Select 15 CPI ................................................................................... 51

Select 60-dpi Graphics.....................................................................52

Select 120-dpi Graphics...................................................................52

Select 120-dpi Graphics...................................................................53

Select 240-dpi Graphics...................................................................53

Select an International Character Set ..............................................54

Select Bit Image ...............................................................................55

Select Bold Font............................................................................... 56

Cancel Bold Font..............................................................................56

Select Character Style .....................................................................56

Select Character Table ....................................................................57

Select Condensed Printing...............................................................57

Select Condensed Printing...............................................................58

Cancel Condensed Printing .............................................................58

Select DBCS Print Quality................................................................ 59

Select Double-strike Printing ............................................................59

Cancel Double-strike Printing........................................................... 59

Select Double-width Printing (One Line) ..........................................60

Cancel Double-width Printing (One Line).........................................60

Select Double-width Printing in DBCS Mode

(One Line) ........................................................................................ 61

Table Of Contents

Cancel Double-width Printing in DBCS Mode

(One Line) ........................................................................................61

Select DBCS Mode ..........................................................................62

Cancel DBCS Mode .........................................................................62

Select Hangul Myunjo/Gothic Style..................................................62

Select Italic Font...............................................................................63

Cancel Italic Font .............................................................................63

Select Print Quality...........................................................................63

Select Printer....................................................................................64

Deselect Printer................................................................................64

Select Superscript/Subscript Printing ...............................................64

Cancel Superscript/Subscript Printing..............................................65

Select DBCS Super/Subscript Printing.............................................65

Select Vertical Printing .....................................................................65

Cancel Vertical Printing (Select Horizontal Printing) ........................66

Set n/60-inch Line Spacing ..............................................................66

Set n/180-inch Line Spacing ............................................................66

Set Absolute Horizontal Print Position..............................................67

Set Bottom Margin ...........................................................................67

Cancel Bottom Margin......................................................................67

Set DBCS Character Half Width.......................................................68

Cancel DBCS Character Half Width and Super/Subscript Printing..68

Set Horizontal Tabs..........................................................................68

Set Intercharacter Space .................................................................69

Set Intercharacter Spacing of DBCS Character

(Hangul Extension)...........................................................................69

Set Intercharacter Spacing Of SBCS Character

(Hangul Extension)...........................................................................70

Set Left Margin.................................................................................70

Set Page Length In Inches...............................................................71

Set Page Length In Lines.................................................................71

Set Relative Horizontal Print Position...............................................72

Set Right Margin ..............................................................................72

Set Vertical Tab Channels ...............................................................73

Set Vertical Tabs..............................................................................73

Set Vertical Tabs In VFU Channels..................................................74

Tab Horizontally ...............................................................................75

Tab Vertically ...................................................................................75

Turn Auto-wrap Around On/Off ........................................................76

Turn Double-Height Printing On/Off .................................................76

Turn Double-Width, Double-Height Printing On/Off .........................77

Turn Double-Width Printing On/Off ..................................................77

Table Of Contents

Turn Extending Table Character On/Off .......................................... 78

Turn On/Off OCRB Selection ...........................................................78

Turn Proportional Mode On/Off........................................................79

Turn Underline On/Off......................................................................79

Turn Underline On/Off (Hangul Extension) ......................................80

A Standard ASCII Character Set ............................. 81

B Code Table........................................................... 83

Korean Standard Code Table (KSC5601) ..............................................83

C Contact Information.............................................. 95

Printronix Customer Support Center.......................................................95

Printronix Supplies Department ..............................................................95

Corporate Offices....................................................................................96

9

1 Introduction

About This Manual

This manual is designed so you can quickly find the information you need to

operate your printer with the Korean Standard (KS) emulation.

This book does not explain how to operate the printer. For printer operation,

see the

User’s Manual.

Warnings And Special Information

Read and comply with all information highlighted under special headings:

WARNING

Conditions that could harm you.

CAUTION

Conditions that could damage the printer or related equipment.

IMPORTANT

Information vital to proper operation of the printer.

NOTE: Information affecting printer operation.

Related Product Information

Refer to the following book for printer operation:

•

User’s Manual.

Provides configuration instructions, descriptions, and

troubleshooting guidelines. Also describes the keys on the control panel

and provides quick reference information on daily printer operations such

as loading paper and replacing ribbons.

Software Features

The KSSM emulation software provides the following features:

• Graphics and print quality. You can enable graphics mode and specify a

density mode (dots per inch), for either 8-pin or 24-pin images.

• Print Attributes. Characters can be bold, italic, double high, double wide,

etc.

• Page Formatting. Commands which allow you to set line spacing, page

length, and vertical tabbing.

• Font Typefaces. Also referred to as print modes. The six typefaces are

LQ, Near LQ, Normal, Hi-Speed, Super Hi-Speed, and Ultra Hi-Speed.

10

Chapter 1 Software Features

11

2 Configuring With The

Control Panel

Introduction

IMPORTANT

Configuration directly affects printer operation. Do not change the

configuration of your printer until you are thoroughly familiar with the

procedures in this chapter.

In order to print data, the printer must respond correctly to signals and

commands received from the host computer. Configuration is the process of

matching the printer's operating characteristics to those of the host computer

and to specific tasks, such as printing labels or printing on different sizes of

paper. The characteristics that define the printer's response to signals and

commands received from the host computer are called configuration

parameters. Examples are line spacing, form length, etc.

You can change the parameters by sending appropriate control codes, or by

pressing keys on the control panel. Control codes offer more versatility, and

they override control panel settings.

This chapter explains how to use the control panel.

Chapter 3 provides information about control codes.

Figure 1. The Control Panel

SET TOF

PRT CONFIG

JOB SELECT

ENTER

ON LINE/CLEAR

PAPER ADVANCE

VIEW/EJECT

CANCEL

Message Display

Status Indicator

Circular

Pad

ONLINE <LP+>

RIBBON LIFE 100%

Emulation

Ribbon Life

Indicator

12

Chapter 2 Printing The Configuration

Printing The Configuration

It is recommended you print a configuration to determine what is already

stored and what needs to be modified.

You can print any or all of the configurations shown above. Configurations 1-8

are the customized configurations.

To print a configuration, follow the procedure in Table 1.

CONFIG.

CONTROL

Load Config.

Save Config. Print Config.

Delete Config.

Power-Up

Config.

Protect

Configs.

Current Short*

Current Full

Factory

Power-Up

All

1

2

3

4

5

6

7

8

* = Factory Default

Name

Configs.

Reset Cfg.

Names

13

Table 1. Printing Configurations

Step Key Result Notes

1. Make sure the printer is on.

2.

3. Allows you to make configuration

changes.

4.

5.

6.

7.

8. Press until the desired option

displays.

9. The configuration listing begins

printing.

10. Carefully tear off the configuration printout.

ON LINE/CLEAR

OFFLINE

QUICK SETUP

+

ENTER SWITCH

UNLOCKED

OFFLINE

QUICK SETUP

OFFLINE

CONFIG. CONTROL

Load Config.

UNTIL

CONFIG. CONTROL

Print Config.

Current Short*

OR

Print Config.

All

ENTER

OFFLINE

CONFIG. CONTROL

14

Chapter 2 Printing The Configuration

NOTE: Another way to print the current configuration is to go OFFLINE,

press the PRT CONFIG key, and then press ENTER.

11. Locks the ENTER key.

12.

13. Store the printout in a safe place. The printer is ready for operation.

Table 1. Printing Configurations (continued)

Step Key Result Notes

+

ENTER SWITCH

LOCKED

ON LINE/CLEAR

ONLINE

15

The Configuration Menu

Figure 2. Configuration Menu Overview

OFFLINE

CONFIG.

CONTROL

HOST

INTERFACE

See the

User’s Manual

LinePrinter+

Printer Protocol

KSSM

Character Sets

Define CR Code

CR Bold Select

Auto LF

Define LF Code

Printer Select

20 CPI Condensed

Alt Set 80-9F

CPI/LPI Select

Host Command

Font Attributes

Graphics Spd Up

Page Format

Reset Cmd CFG Ld

Error Handling

See the

User’s Manual

PRINTER

CONTROL

See the

User’s Manual

See the

User’s Manual

Host Interface

Graphic Spd Up

Typeface

DBCS CPI

Select LPI

DBCS ASCII Style

Ribbon End Point

Reset Cmd CFG Ld

Load Config.

Save Config.

Power-Up Config.

EMULATION

QUICK

SETUP

ADVANCED

USER

See the

User’s Manual

DIAGNOSTICS

16

Chapter 2 The Configuration Menu

Moving Within The Configuration Menu

The example in Table 2 explains how to change the LPI value.

Table 2. Changing Configurations

Step Key Result Notes

1. Make sure the printer is on.

2.

3. Allows you to make configuration

changes.

4.

5.

6.

7.

8.

9.

10. Press until the desired value

displays.

ON LINE/CLEAR

OFFLINE

QUICK SETUP

+

ENTER SWITCH

UNLOCKED

OFFLINE

CONFIG. CONTROL

UNTIL

OFFLINE

EMULATION

LinePrinter+

Printer Protocol

LinePrinter+

CPI/LPI Select

Select LPI

6.0 LPI*

OR

Select LPI

8.0 LPI

Moving Within The Configuration Menu

17

11. An asterisk indicates the value

selected.

12. Use the diagrams on the following pages to navigate your way through the menu.

Press

 or  to move vertically; press  or  to move horizontally and to scroll

through the values. Press ENTER to select a value. Press ONLINE/CLEAR, to move

to the top of the menu.

To SAVE CHANGES AS A CONFIGURATION that is stored in memory and can be loaded

later:

13.

14.

15. Go to Table 3, step 4.

To USE CURRENT CONFIGURATION WITHOUT SAVING:

16. Locks the configuration

parameters.

17.

18. The printer is ready for operation. All parameters are effective as long as the printer is

on. When you turn off the printer, the parameters will be erased from memory.

Table 2. Changing Configurations (continued)

Step Key Result Notes

ENTER

Select LPI

8.0 LPI*

UNTIL

OFFLINE

EMULATION

UNTIL

OFFLINE

CONFIG. CONTROL

+

ENTER SWITCH

LOCKED

ON LINE/CLEAR

ONLINE

18

Chapter 2 The Configuration Menu

Saving Your New Configuration

After changing all of the necessary parameters, it is recommended you save

them as a configuration that can be stored for future use and loaded later. If

you do not save your configuration before you power off the printer, all of your

parameter changes will be erased. The Save Config. option allows you to

save up to eight configurations to meet different print job requirements.

Configurations 1 through 8 are empty until you save values to them using the

Save Config. option. For example:

Config 1: Selects LQ typeface, 5 cpi, 6 lpi

Config 2: Selects Near LQ typeface, 6 cpi, 8 lpi

Once you have saved a configuration using this option, it will not be lost if you

power off the printer. You can load a configuration for a specific print job and

modify and resave it. You may want to print your configurations and store

them in a safe place, such as inside the printer cabinet.

NOTE: The Protect Configs. parameter must be set to disable before you can

save a configuration. Once you save a configuration, the Protect

Configs. parameter automatically returns to enable. Once you change

active emulations, any changes to the previously selected emulation

will be gone unless they have been saved.

* = Factory Default

CONFIG.

CONTROL

Load Config.

Save Config. Print Config.

Delete Config.

Power-Up

Config.

Protect

Configs.

1

2

3

4

5

6

7

8

Name Configs. Reset Cfg.

Names

Saving Your New Configuration

19

Table 3. Saving Configurations

Step Key Result Notes

1. If you are already in the configuration menu, go to step 5.

2.

3. Allows you to make configuration

changes.

4.

5.

6.

7.

8. Press until the desired number

(1-8) displays.

NOTE: Do not turn off the printer while Save is in progress because you might lose your

configuration.

9. The configuration is now saved in

memory. (In this case, config. 2.)

10.

ON LINE/CLEAR

OFFLINE

QUICK SETUP

+

ENTER SWITCH

UNLOCKED

OFFLINE

QUICK SETUP

OFFLINE

CONFIG. CONTROL

Load Config.

CONFIG. CONTROL

Save Config.

1*

OR

Save Config.

2

ENTER

Save Config.

2*

UNTIL

CONFIG. CONTROL

Save Config.

20

Chapter 2 The Configuration Menu

NOTE: It is recommended you print the configuration. Go to page 13, step 5. If you decide not

to print the configuration, then continue with the following steps.

10. Locks the ENTER key.

11.

12. The printer is ready for operation.

Table 3. Saving Configurations (continued)

Step Key Result Notes

+

ENTER SWITCH

LOCKED

ON LINE/CLEAR

ONLINE

Page is loading ...

Printronix P7000 H-Series User manual

This manual is also suitable for

Printronix P7000 H-Series User manual

Related papers

Other documents