Atrie wirespan 5100b Installation guide

Type
Installation guide
xDSL Bridge
WireSpan 5100B
Installation Guide
(Version 1.00)
ATRIE
TECHNOLOGY INC.
10F, No.14, Lane 609, Sec. 5, Chung Hsin Rd.,
San Chung City, Taipei Hsien, Taiwan, R.O.C.
Tel : (886)2-2999-5155 Fax : (886)2-2999-4960
Website : http://www.atrie.com.tw E-mail : c[email protected]trie.com.tw
2
WireSpan 5100B xDSL Bridge
The WireSpan 5100B G.SHDSL Bridge provides a high-speed data
connection over a single-pair copper line to another one. The
WireSpan 5100B uses Single-pair Digital Subscriber Line (SDSL)
technology to provide data rates from 64Kbps to 2312Kbps. The
data rate is manually configured, based on the connection
distance and line condition.
The WireSpan 5100B connects, through its 10/100BaseT port, to
a PC or Local Area Network (LAN).
Determining the data rate
The following chart shows the maximum reach, on 24 AWG and
26 AWG wire, for each data rate the WireSpan 5100B supports. The
actual reach depends on such factors as the condition of the line
and the presence of bridge taps, splices, line noise, and so on.
26AWG Simulator
3.6
3.75
4.05
4.2
4.65
5.1
6.15
6.75
7.2
7.5
7.65
8.4
0
2
4
6
8
10
2312 2056 1544 1160 1032 776 520 392 264 200 136 72
Line Rate(Kbps)
Instants(km
)
Features
The WireSpan 5100B provides MAC layer bridging of frames
received on its LAN and WAN interfaces. It provides transparent
address learning -- storing up to 1024 MAC addresses -- on the
LAN interface. Address entries are aged out after 300 seconds. The
WireSpan 5100B does not support spanning tree. As a result, it can
not be used in parallel with another bridge to provide redundancy.
The WireSpan 5100B is easy to install. Set the transmission rate
with a DIP switch on the back panel and connect the cables, and
it's ready to use.
The WireSpan 5100B uses a dedicated single-pair wire to connect a
subscriber PC or LAN to an DSL line.
3
Ethernet
PC
PC
WireSpan 5100B
3.6Km~8.7Km
2Wire/26AWG
WireSpan 5100B
Ethernet
Ethernet
WireSpan 5100B
3.6Km~8.7Km
2Wire/26AWG
WireSpan 5100B
Ethernet
HUB HUB
PC
PC
PC
PC
PC
PC
Technical Specifications
Power Supply Power Adaptor DC 5V±5%
Connectors
Ethernet Connector RJ-45 connector for 10/100BaseT interface
DSL Connector RJ-11 connector for DSL interface
Physical
Height 37mm
Width 127.5mm
Length 161mm
Weight 276g
Environmental
Operating temperature 0 to 50 °C
Relative humidity Up to 95% Non-condensing
Storage temperature -10 to 70 °C
Pin Definition
The table lists the pinouts for the WireSpan 5100B ports. Pins not
listed are not assigned.
DSL Port 10/100BaseT Port (PC) 10/100BaseT Port (HUB)
Pin 3: DSL Ring Pin 1: RD+ Pin 2: RD- Pin 1: TD+ Pin 2: TD-
Pin 4: DSL Tip Pin 3: TD+ Pin 6: TD- Pin 3: RD+ Pin 6: RD-
4
DSL Port
1. --
2: Ring for DSL
3: Tip for DSL
4. --
10/100BaseT Port (PC)
1: RD+
2: RD-
3: TD+
4: --
5: --
6: TD-
7: --
8: --
10/100BaseT Port (HUB)
1: TD+
2: TD-
3: RD+
4: --
5: --
6: RD-
7: --
8: --
Console Port
This console port is for user to control the device via terminal.
Please adjust your terminal emulation software according to the
following table:
PARAMETERS VALUE
Speed (baud rate) 38400bps
Data bits 8 bits
Parity None
5
Stop bit 1 bit
Flow control None
Terminal emulation VT-100 or ANSI
Received Data (RD)
NC
NC
From
From
From
From
Transmitted Data (TD)
Data Terminal Ready (DTR)
Ground (GND)
2
3
4
5
1
6
9
8
7
Common
DTE
DCE
DTE
NC
NC
NC
Panel Description
Front Panel
WireSpan 5100B
Bridge
SYNLINK ACTPWR TST
SQ
PWR
Power On : Power is available
Off : Power is off
LINK On: Network link is up
Off: Link is down
Rear Panel
6
ON
21 435 87
Power Switch
Power Connector
Console Port
Central/Remote, Rate Selector
Power Connecto
r
10/100BaseT Port
DSL Port
TST On : Modem is on the diagnostic
Off : Modem is on the test
ACT Flashing : Transmitting/receiving data
Off : No data transmitting/receiving
SQ On : Signal quality is good
Flashing : Signal quality is poor
SYN Flashing : Establishing SDSL link
On : Link is up
6
DIP Switch
8
7
6
54
321
ON
SW
POSITION 1 - Central, Remote selection
1 Description
OFF Remote side
ON Central side
Note : One device is setting to Central side,
the other is setting to Remote side.
POSITION 2,3 - Ethernet line speed selection
2 3 Description
OFF OFF AUTO(Half/Full)
OFF ON 10Mbps Half Duplex
ON OFF 100Mbps Half Duplex
ON ON Reserved
POSITION 4,5,6,7 - DSL rate selection
4 5 6 7 Description
OFF OFF OFF OFF AUTO
OFF OFF OFF ON 72Kbps
OFF OFF ON OFF 136Kbps
OFF OFF ON ON 200Kbps
OFF ON OFF OFF 264Kbps
OFF ON OFF ON 392Kbps
OFF ON ON OFF 520Kbps
OFF ON ON ON 648Kbps
ON OFF OFF OFF 776Kbps
ON OFF OFF ON 1032Kbps
ON OFF ON OFF 1160Kbps
ON OFF ON ON 1544Kbps
ON ON OFF OFF 1928Kbps
7
ON ON OFF ON 1992Kbps
ON ON ON OFF 2056Kbps
ON ON ON ON 2312Kbps
POSITION 8- NVRAM/DIP switch selection
8 Description
OFF Read NVRAM for power on configuration.
ON Read DIP for switch for power on configuration.
Connect the cables
To DSL Port
Connect cable to
To PC COM Port
HUB : a local net work via an
Ethernet device such
as HUB or SWITCH
PC : a PC
To wall jack
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Atrie wirespan 5100b Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI