Read the instructions and precautions before use of this product
Please keep this instruction manual for future reference
®
Model No: 50104260
Freedom Bench
by R.A. Guthrie
Instruction Manual
For warranty information, please refer to the back page of
this instruction manual.
080911rev3
Due to ongoing product development
the actual product or products may vary from
the illustrations or photos shown within this manual.
NOTE: This product is intended for residential, non-commercial use.
Made in China
©2012 World Factory, Inc.
Distributed by:
World Factory, Inc.
Westlake, TX 76262
For Manuals, Replacement Parts or Customer Service visit:
www.ezreplacement.com
Limited Warranty
World Factory, Inc. Products for Home Use
World Factory, Inc. (Seller) warrants to the original Buyer only, that each Astonica Product will be free
from defects in material and workmanship for a period of one (1) year from date of purchase.
SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH
ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE SELLER
WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY FROM
REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER
MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This
warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to
normal use or weathering. To make a claim under this Limited Warranty, you must return the complete
product with proof of purchase, transportation prepaid, to any World Factory, Inc. authorized service
center. Call 1-888-422-7800 or visit: ezreplacement.com for the location of the nearest authorized
service center.
Additional Limitations
THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED
TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)
YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF
PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.
If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such
provision shall not affect any other provision herein, this Limited Warranty shall be construed as if
such invalid and/or unenforceable provision had never been contained herein.
This warranty gives you special legal rights, and you may also have other rights which vary from state
to state.
This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all
prior agreements, arrangements, or understandings between the parties relating to product warranty.
C
H
H
G
G
I
I
D
E
E
E
E
F
F
A
B
F
F
Figure 1
ASSEMBLY INSTRUCTIONS
PARTS & HARDWARE LIST
PART # DESCRIPTION QUANTITY
B
C
E F
H
I
G
J
Carefully remove the contents from the package. If any parts are missing do not
attempt to use the product until they have been obtained and correctly installed.
CAUTION: Do not over tighten fasteners.
H
H
G
G
I
I
A
NOTE: This product is intended for residential, non-commercial use.
A Back 1
B Seat 1
C Right Leg 1
D Left Leg 1
E Screw, M6 x 50mm 4
F Screw, M6 x 68mm 4
G Hex Nut, 6mm 8
H Flat Washer, 6mm 8
I Plastic Nut Cover 8
J Hex Key 1
K End Cap (Pre-Installed) 2
L Foot Cap (Pre-Installed) 4
D
Parts Detail
Note: Identify the right and left legs by locating the round white label with the letters “C” and “D”
on each. From a seated position, the left leg (D) crossbar has an indention on the inside of
the crossbar. The same is true for the right leg (C).
1. (SEE FIGURE 1) Attach seat (B) to left leg (D) by aligning holes in the leg crossbar with
corresponding holes in seat frame. Using hex key (J) secure screws (E), flat washers (H) and
hex nuts (G). Attach seat (B) to right leg (C) by aligning holes in the leg with corresponding
holes in seat frame. Using hex key (J) secure screws (E), flat washers (H) and hex nuts (G). Do
not fully tighten fasteners.
2. Slide back (A) between legs (C/D) and align holes. Insert screws (F) through holes. Using hex
key (J) secure with flat washers (H) and hex nuts (G).
3. Place bench upright on a flat, level surface and tighten all fasteners. Slide plastic nut covers (I)
over all exposed nuts.
Left
Right
K
L
K
L
/
