Atdec AF-AA Installation guide

Category
Flat panel desk mounts
Type
Installation guide

Atdec AF-AA is a versatile accessory arm designed to provide flexible mounting solutions for monitors and other compatible devices. With a weight range of 0-8kg (0-17.6lbs), it offers sturdy support for various display sizes. The arm features adjustable height, tilt, pan, and rotation, allowing for optimal positioning and viewing angles. It comes with cable management options to keep your workspace organized and clutter-free. Compatible with Atdec's range of poles and arms, the AF-AA provides a secure and ergonomic setup, enhancing productivity and comfort in your workspace.

Atdec AF-AA is a versatile accessory arm designed to provide flexible mounting solutions for monitors and other compatible devices. With a weight range of 0-8kg (0-17.6lbs), it offers sturdy support for various display sizes. The arm features adjustable height, tilt, pan, and rotation, allowing for optimal positioning and viewing angles. It comes with cable management options to keep your workspace organized and clutter-free. Compatible with Atdec's range of poles and arms, the AF-AA provides a secure and ergonomic setup, enhancing productivity and comfort in your workspace.

AF-AA Page 1 of 4
COMPONENT CHECKLIST
B
Monitor
arm
(x1)
C
Hand grip assembly
(x1)
A
VESA
head
(x1)
D
Rotation
limiter
(x1)
G
Security Screw
M4 x 16mm
(x1)
H
Mounting
screws
M4 x 10mm
(x4)
I
Mounting
screws
M4 x 12mm
(x4)
J
Mounting
screws
M4 x 16mm
(x4)
E
Primary arm
cable cover
(x1)
F
Secondary arm
cable cover
(x1)
Installation Guide
AF-AA
Accessory Arm
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! This product is compatible with the range of AF Poles and arms.
! The manufacturer accepts no responsibility for incorrect installation.
REQUIRED TOOLS
WEIGHT RANGE
• Phillips Head Screwdriver
0 - 8kg
(0 - 17.6lbs)
AF-AA Page 2 of 4
1. Install VESA monitor head
2. Install arm assembly
5mm
Allen Key
Pole
Top Cap
Spacers (may be required
for recessed and uneven
surfaces)
VESA monitor
head
Screen
M4x10/12/16mm
Phillips Head Mounting
Screws
1.1 Install VESA monitor head as shown.
2.1 Remove Top Cap and Allen key
from existing AF- pole product
2.4 Place arm and
handgrip on to the pole
Note Ensure handgrip tab
lines up with slot in pole
2.5 Turn the handgrip to fix the height of the arm
and place the top cap back on to the pole
2.3 Place handgrip tab
in arm assembly
100mm
100mm
Arm Assembly
2.2 OPTIONAL ROTATION LIMITER
Insert rotation limiter for 180�
rotation around mounting pole
AF-AA Page 3 of 4
4.1 Unlock Handgrip ensuring both the
screen and arm assembly are supported
4.2 Lift/Lower the Screen to the desired
height. Move both Screen and Arm
assembly together
4.3 Lock Handgrip firmly
4. Adjusting Height
5. Cable Management
3. Mounting Monitor
VESA monitor head
Arm Assembly
3.2 OPTIONAL SECURITY SCREW
Ensure the Monitor is supported, then loosen the Monitor head
screw with the 5mm Allen Key and tilt screen up before installing
the M4 x 16mm Security Screw into the Security Screw hole
Note: Support Screen
when adjusting tilt.
3.1 Insert VESA monitor head into
the receptacle in the Arm Assembly
5mm Allen Key
Phillips Head
Screwdriver
Loosen
Tighten
Security Screw
Hole
M4 x 16mm
Security Screw
Monitor head
screw
Lock Slot
Elbow Joint
‘click’
‘click’
Lock Slot
Elbow Joint
‘click’
‘click’
5.1 After plugging in your cables,
install the Cable Covers.
Insert Cable Covers
up into Lock Slots.
5.2 Push Cable Covers away from
Elbow Joint to secure in place.
5.3 Cable Clips and Cable Stops can be installed
to further manage cables.
Cable Stop
Cable Clip
Note: Ensure enough cable
slack is given to allow for
movement.
AF-AA Page 4 of 4
Adjusting the Display Bracket
Portrait/ Landscape Tilt (Screen angle up/down) Pan (Screen angle left/right)
5mm Allen Key
Tighten
Loosen
No Allen Key necessary No Allen Key necessaryNote: Support Screen when adjusting tilt.
5. Cable Management (Cont)
Press down firmly onto the
other edge of the Cable Stop
and hold. This allows the rear
profile to flex in place
Insert Cable Stop on one edge of
the Pole Slot
Allen Key
Storage
atdec.com | atdec.co.uk | atdec.com.au
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specifications without notice. ©20180206B
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Atdec AF-AA Installation guide

Category
Flat panel desk mounts
Type
Installation guide

Atdec AF-AA is a versatile accessory arm designed to provide flexible mounting solutions for monitors and other compatible devices. With a weight range of 0-8kg (0-17.6lbs), it offers sturdy support for various display sizes. The arm features adjustable height, tilt, pan, and rotation, allowing for optimal positioning and viewing angles. It comes with cable management options to keep your workspace organized and clutter-free. Compatible with Atdec's range of poles and arms, the AF-AA provides a secure and ergonomic setup, enhancing productivity and comfort in your workspace.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI