Gigabyte R263-S33 User manual

R263-S33-AAF1

R263-S33-AAL1

4th Gen. Intel® Xeon® Scalable Server System - 2U UP 12-Bay NVMe/SATA/SAS

User Manual

Rev. 1.0

Copyright

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of Giga Computing.

Changes to the specications and features in this manual may be made by Giga Computing

without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or

published in any form or by any means without Giga Computing's prior written permission.

Documentation Classications

In order to assist in the use of this product, Giga Computing provides the following types of documen-

tation:

 User Manual: detailed information & steps about the installation, conguration and use of this

product (e.g. motherboard, server barebones), covering hardware and BIOS.



User Guide: detailed information about the installation & use of an add-on hardware or

software component (e.g. BMC rmware, rail-kit) compatible with this product.

 Quick Installation Guide: a short guide with visual diagrams that you can reference easily for

installation purposes of this product (e.g. motherboard, server barebones).

Please see the support section of the online product page to check the current availability of these

documents.

For More Information

For related product specications, the latest rmware and software, and other information please visit our website at

http://www.gigabyte.com/Enterprise

For GIGABYTE distributors and resellers, additional sales & marketing materials are available from our reseller

portal: http://reseller.b2b.gigabyte.com

For further technical assistance, please contact your GIGABYTE representative or visit

https://esupport.gigabyte.com/ to create a new support ticket

For any general sales or marketing enquiries, you may also message GIGABYTE server directly by email:

server[email protected]

Conventions

The following conventions are used in this user's guide:

NOTE!

Gives bits and pieces of additional

information related to the current topic.

CAUTION!

Gives precautionary measures to

avoid possible hardware or software problems.

WARNING!

Alerts you to any damage that might

result from doing or not doing specic actions.

Server Warnings and Cautions

Before installing a server, be sure that you understand the following warnings and cautions.

WARNING!

To reduce the risk of electric shock or damage to the equipment:

• Do not disable the power cord grounding plug. The grounding plug is an important safety

feature.

• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all

times.

• Unplug all the power cords from the power supplies to disconnect power to the equipment.

•

• Shock Hazard! Disconnect all power supply cords before servicing.

• Do not route the power cord where it can be walked on or pinched by items placed against it.

Pay particular attention to the plug, electrical outlet, and the point where the cord extends from

the server.

WARNING!

To reduce the risk of personal injury from hot surfaces, allow the drives

and the internal system components to cool before touching them.

WARNING!

This server is equipped with high speed fans. Keep away from hazardous

moving fan blades during servicing.

WARNING!

This equipment is intended to be used in Restrict Access Location. The

access can only be gained by Skilled person. Only authorized by well

trained professional person can access the restrict access location.

CAUTION!

• Do not operate the server for long periods with the access panel open or removed. Operat-

ing the server in this manner results in improper airow and improper cooling that can lead to

thermal damage.

• Danger of explosion if battery is incorrectly replaced.

• Replace only with the same or equivalent type recommended by the manufacturer.

• Dispose of used batteries according to the manufacturer’s instructions.

CAUTION!

Risk of explosion if battery is replaced incorrectly or with an incorrect type. Replace the battery

only with the same or equivalent type recommended by the manufacturer. Dispose of used bat-

teries according to the manufacturer’s instructions.

Electrostatic Discharge (ESD)

CAUTION!

ESD CAN DAMAGE DRIVES, BOARDS, AND OTHER PARTS. WE RECOMMEND THAT YOU

PERFORM ALL PROCEDURES AT AN ESD WORKSTATION. IF ONE IS NOT AVAILABLE,

PROVIDE SOME ESD PROTECTION BY WEARING AN ANTI-STATIC WRIST STRAP AT-

TACHED TO CHASSIS GROUND -- ANY UNPAINTED METAL SURFACE -- ON YOUR SERVER

WHEN HANDLING PARTS.

Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by

their edges without any component and pin touching. After removing a board from its protective

wrapper or from the system, place the board component side up on a grounded, static free sur-

face. Use a conductive foam pad if available but not the board wrapper. Do not slide board over

any surface.

System power on/o: To remove power from system, you must remove the system from

rack. Make sure the system is removed from the rack before opening the chassis, adding, or

removing any non hot-plug components.

Hazardous conditions, devices and cables: Hazardous electrical conditions may be

present on power, telephone, and communication cables. Turn off the system and disconnect the

cables attached to the system before servicing it. Otherwise, personal injury or equipment dam-

age can result.

Electrostatic discharge (ESD) and ESD protection: ESD can damage drives,

boards, and other parts. We recommend that you perform all procedures in this chapter only at

an ESD workstation. If one is not available, provide some ESD protection by wearing an antistatic

wrist strap attached to chassis ground (any unpainted metal surface on the server) when handling

parts.

ESD and handling boards: Always handle boards carefully. They can be extremely

sensitive to electrostatic discharge (ESD). Hold boards only by their edges. After removing a

board from its protective wrapper or from the system, place the board component side up on a

grounded, static free surface. Use a conductive foam pad if available but not the board wrapper.

Do not slide board over any surface.

Installing or removing jumpers: A jumper is a small plastic encased conductor that slips

over two jumper pins. Some jumpers have a small tab on top that can be gripped with ngertips

or with a pair of ne needle nosed pliers. If the jumpers do not have such a tab, take care when

using needle nosed pliers to remove or install a jumper; grip the narrow sides of the jumper with

the pliers, never the wide sides. Gripping the wide sides can dam-age the contacts inside the

jumper, causing intermittent problems with the function con-trolled by that jumper. Take care to

grip with, but not squeeze, the pliers or other tool used to remove a jumper, or the pins on the

board may bend or break.

- 6 -

Table of Contents

Chapter 1 Hardware Installation .....................................................................................9

1-1 Installation Precautions .................................................................................... 9

1-2 Product Specications .................................................................................... 10

1-3 System Block Diagram ................................................................................... 14

Chapter 2 System Appearance .....................................................................................15

2-1 Front View ...................................................................................................... 15

2-2 Rear View ....................................................................................................... 16

2-3 Front Panel LEDs and Buttons ....................................................................... 17

2-3-1 RoT LEDs ...............................................................................................................18

2-4 Rear System LAN LEDs ................................................................................. 20

2-5 Power Supply Unit (PSU) LED ....................................................................... 21

2-6 Hard Disk Drive LEDs .................................................................................... 22

Chapter 3 System Hardware Installation ......................................................................23

3-1 Removing Chassis Cover ............................................................................... 24

3-2 Removing and Installing the Fan Duct ........................................................... 25

3-3 Removing and installing the Heat Sink .......................................................... 26

3-4 Installing the CPU .......................................................................................... 27

3-5 Installing the Memory ..................................................................................... 29

3-5-1 Eight Channel Memory Conguration .....................................................................29

3-5-2 Installing the Memory ............................................................................................30

3-5-3 DIMM Population Table ..........................................................................................30

3-5-4 Processor and Memory Module Matrix Table .........................................................31

3-6 Installing the PCI Expansion Card ................................................................. 32

3-7 Installing the Mezzanine Card ........................................................................ 33

3-7-1 OCP 3.0 ..................................................................................................................33

3-8 Installing the Hard Disk Drive ......................................................................... 34

3-9 Installing the M.2 Device and Heat Sink ........................................................ 36

3-10 Replacing the Fan Assembly .......................................................................... 37

3-11 Replacing the Power Supply .......................................................................... 38

3-12 Cable Routing ................................................................................................ 39

Chapter 4 Motherboard Components ...........................................................................43

4-1 Motherboard Components ............................................................................. 43

4-2 Jumper Setting .............................................................................................. 45

- 7 -

4-3 Backplane Board Storage Connector ............................................................ 46

4-3-1 CBP20C5 ................................................................................................................46

Chapter 5 BIOS Setup ..................................................................................................47

5-1 The Main Menu .............................................................................................. 49

5-2 Advanced Menu ............................................................................................. 52

5-2-1 Trusted Computing .................................................................................................53

5-2-2 Serial Port Console Redirection .............................................................................54

5-2-3 SIO Conguration ...................................................................................................57

5-2-4 PCI Subsystem Settings .........................................................................................58

5-2-5 USB Conguration ..................................................................................................60

5-2-6 Network Stack Conguration ..................................................................................61

5-2-7 Post Report Conguration ......................................................................................62

5-2-8 NVMe Conguration ...............................................................................................63

5-2-9 Chipset Conguration .............................................................................................64

5-2-10 Tls Auth Conguration ............................................................................................65

5-2-11 iSCSI Conguration ................................................................................................66

5-2-12 Intel(R) Ethernet Controller X710 for 10GBASE-T .................................................67

5-2-13 VLAN Conguration ................................................................................................69

5-2-14 Driver Health ...........................................................................................................70

5-3 Chipset Menu ................................................................................................. 71

5-3-1 Processor Conguration .........................................................................................72

5-3-2 Common RefCode Conguration ...........................................................................75

5-3-3 UPI Conguration ...................................................................................................76

5-3-4 Memory Conguration ............................................................................................78

5-3-5 IIO Conguration ....................................................................................................81

5-3-6 Advanced Power Management Conguration ........................................................83

5-3-7 PCH Conguration ..................................................................................................85

5-3-8 Miscellaneous Conguration ..................................................................................87

5-3-9 Server ME Conguration ........................................................................................88

5-3-10 Runtime Error Logging Settings .............................................................................89

5-3-11 Power Policy ...........................................................................................................91

5-4 Server Management Menu ............................................................................. 93

5-4-1 System Event Log ..................................................................................................95

5-4-2 View FRU Information ............................................................................................96

5-4-3 BMC VLAN Conguration .......................................................................................97

5-4-4 BMC Network Conguration ...................................................................................98

5-4-5 IPv6 BMC Network Conguration ...........................................................................99

5-5 Security Menu .............................................................................................. 100

5-5-1 Secure Boot .........................................................................................................101

- 8 -

5-6 Boot Menu .................................................................................................... 104

5-7 Save & Exit Menu ......................................................................................... 106

5-8 BIOS Recovery ............................................................................................ 108

5-9 BIOS POST Beep code (AMI standard) ....................................................... 109

5-9-1 PEI Beep Codes ...................................................................................................109

5-9-2 DXE Beep Codes .................................................................................................109

Hardware Installation

- 9 -

1-1 Installation Precautions

The motherboard/system contain numerous delicate electronic circuits and components which

can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully

read the service guide and follow these procedures:

• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

• Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

• When connecting hardware components to the internal connectors on the motherboard,

make sure they are connected tightly and securely.

• When handling the motherboard, avoid touching any metal leads or connectors.

• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

components such as a motherboard, CPU or memory. If you do not have an ESD wrist

strap, keep your hands dry and rst touch a metal object to eliminate static electricity.

•

Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

• Before unplugging the power supply cable from the motherboard, make sure the power

supply has been turned off.

• Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

• Before using the product, please verify that all cables and power connectors of your

hardware components are connected.

• To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

• Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

• Do not place the computer system on an uneven surface

.

• Do not place the computer system in a high-temperature environment.

• Turning on the computer power during the installation process can lead to damage to

system components as well as physical harm to the user.

• If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certied computer technician.

Chapter 1 Hardware Installation

Hardware Installation

- 10 -

1-2 Product Specications

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

System

Dimension

2U

438mm (W) x 87.5mm (H) x 710mm (D)

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

CPU 4th Generation Intel® Xeon® Scalable Processors

Intel® Xeon® Platinum Processor, Intel® Xeon® Gold Processor,

Intel® Xeon® Silver Processor

CPU TDP up to 350W

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

Socket 1 x LGA 4677

Socket E

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

Chipset Intel® C741 Chipset

Socket

Security

Security UEFI Secure Boot

Silicon root of trust (Option)

SNMP Support: V3

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

Memory 16 x DIMM slots

DDR5 memory supported only

8-Channel memory architecture

RDIMM modules up to 96GB supported

3DS RDIMM modules up to 256GB supported

Memory speed: Up to 4800 MHz (1DPC), 4400 MHz (2DPC)

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

LAN 1 x 1Gb/s LAN port (1 x Intel® I210-AT)

Supported NCSI function

1 x 10/100/1000 management LAN

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

Video Integrated in Aspeed® AST2600

2D Video Graphic Adapter with PCIe bus interface

1920x1200@60Hz 32bpp, DDR4 SDRAM

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

Storage 12 x 3.5/2.5" SATA/SAS hot-swappable bays

SAS card is required for SAS devices support

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

RAID Intel® SATA RAID 0/1/10/5

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

Expansion Slot Riser Card CRS201C:

- 1 x PCIe x16 slot (Gen5 x16), FHHL

Riser Card CRS201D:

- 1 x PCIe x16 slot (Gen5 x16), FHHL

Riser Card CRS2018:

- 1 x PCIe x16 slot (Gen4 x16), FHHL

2 x OCP 3.0 slots with PCIe Gen5 x16 bandwidth

- Supported NCSI function

NOTE:

We reserve the right to make any changes to the product specications and product-related

information without prior notice.

Hardware Installation

- 11 -

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

Expansion Slot 1 x M.2 slot:

- M-key

- PCIe Gen3 x4

- Supports NGFF-2280/22110 cards

- From PCH (C741)

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

Internal I/O 1 x M.2 slot

1 x TPM header

2 x OCP 3.0 mezzanine slots

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

Front I/O 2 x USB 3.2 Gen1

1 x Power button with LED

1 x ID button with LED

1 x NMI button

1 x Reset button

1 x LAN activity LED

1 x HDD activity LED

1 x System status LED

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

Rear I/O 2 x USB 3.2 Gen1

1 x Mini-DP

1 x RJ45

1 x MLAN

1 x ID button with LED

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

Backplane I/O Backplane P/N: 9CBP20C5NR-00

Speed and bandwidth: PCIe Gen4 x4 or SATA 6Gb/s or SAS 12Gb/s

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

TPM 1 x TPM header with SPI interface

Optional TPM2.0 kit: CTM010

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

Power Supply R263-S33-AAF1

Dual 2400W (240V) 80 PLUS Platinum redundant power supply

AC Input:

- 100-127V~/ 12.5A, 47-63Hz

- 180-240V~/ 14.5A, 47-63Hz

DC Input:

- 240Vdc, 12A

DC Onput:

- Max 1000W/ 100-127V

+12V/ 84A

+12Vsb/ 3A

- Max 2200W/ 180-200V

+12V/ 180A

+12Vsb/ 3.5A

- Max 2400W/ 200-240V or 240Vdc

+12V/ 197A

+12Vsb/ 3.5A

Hardware Installation

- 12 -

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

Power Supply R263-S33-AAL1

Dual 2700W (240V) 80 PLUS Titanium redundant power supply

AC Input:

- 100-127V~/ 12A, 50-60Hz

- 200-240V~/ 16A, 50-60Hz

DC Input:

- 240Vdc/ 16A

DC Onput:

- Max 1008W/ 100-127V~

+ 12V/ 84A

+ 12Vsb/ 3A

- Max 2700W/ 200-240V~

+ 12V/ 225A

+ 12Vsb/ 3A

NOTE:

1. The system power supply requires C19 type power cord

2. The default power supply is based on a basic system conguration. Please

contact with technical representatives to determine the best power supply

selection for your system conguration requirements and preferred efciency.

3. The power supply specications provided herein is for the default server

conguration. Different SKUs have different PSU specs, so please see the

system rating label on the server for the accurate PSU specication.

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

System

Management

Aspeed® AST2600 management controller

GIGABYTE Management Console (AMI MegaRAC SP-X) web interface

Dashboard

HTML5 KVM

Sensor Monitor (Voltage, RPM, Temperature, CPU Status …etc.)

Sensor Reading History Data

FRU Information

SEL Log in Linear Storage / Circular Storage Policy

Hardware Inventory

Fan Prole

System Firewall

Power Consumption

Power Control

LDAP / AD / RADIUS Support

Backup & Restore Conguration

Remote BIOS/BMC/CPLD Update

Event Log Filter

User Management

Media Redirection Settings

PAM Order Settings

SSL Settings

SMTP Settings

Hardware Installation

- 13 -

Socket

Security

Security Server Operating Properties

Power Supply

System fanSystem fanSystem fan

Operating

Properties

Operating temperature: 10°C to 35°C

Operating humidity: 8-80% (non-condensing)

Non-operating temperature: -40°C to 60°C

Non-operating humidity: 20%-95% (non-condensing)

Hardware Installation

- 14 -

1-3 System Block Diagram

System Appearance

- 15 -

Chapter 2 System Appearance

2-1 Front View

1 23

HDD0

HDD1

HDD2

HDD3

HDD4

HDD5 HDD8

HDD9

HDD6

HDD7 HDD10

HDD11

No. Description

1. Front Panel LEDs and Buttons

2. Front USB 3.2 Gen1 Ports

3. 3.5"/2.5" Drive Bays

NOTE! Drives with green latches support NVMe.

• Please Go to Chapter 2-3 Front Panel LED and Buttons for detail description of function LEDs.

System Appearance

- 16 -

2-2 Rear View

83 5 7

1

2 4 6

1

PSU1

PSU2

SLOT2

SLOT5SLOT4

SLOT1

Reserved

SLOT6

SLOT7

SLOT3

No. Description

1. PCIe Slot

2. OCP 3.0 Slot (Option/SFF)

3. Mini DP Port

4. USB 3.2 Gen1 Port x 2

5. 10/100/1000 Server Management LAN Port

6. 1GbE LAN Port

7. ID Button

8. OCP 3.0 Slot (Option/SFF)

System Appearance

- 17 -

2-3 Front Panel LEDs and Buttons

(Note) If your server features RoT function, please see the following section for detail LED behavior.

L1 L2

1

3

5

7

2

4

6

8

No. Name Color Status Description

1. Reset Button Press the button to reset the system.

2. NMI button

Press the button server generates a NMI to the processor

if the multiple-bit ECC errors occur, which effectively halt

the server.

3. Power button

with LED

Green On System is powered on

N/A Off System is not powered on or in ACPI S5 state (power off)

4. ID Button(Note) Press the button to activate system identication

5. HDD Status

LED

Green On HDD locate

Blink HDD access

Amber On HDD fault

Green/

Amber Blink HDD rebuilding

N/A Off No HDD access or no HDD fault.

6.

System

Status

LED(Note)

Green Solid On System is operating normally.

Amber

Solid On Critical condition, may indicate:

System fan failure; System temperature

Blink

Non-critical condition, may indicate:

Redundant power module failure

Temperature and voltage issue

Chassis intrusion

N/A Off System is not ready, may indicate:

POST error; NMI error; Processor or terminator missing

7. LAN 1 Active/

Link LED

Green Solid On Link between system and network or no access.

Green Blink Data trasmission or receiving is occuring

N/A Off No data transmission or receiving is occuring

8. LAN 2 Active/

Link LED The function is disabled.

System Appearance

- 18 -

2-3-1 RoT LEDs

L1 L2

Status LE

D

ID LED

LED on Front panel(Note5)

ID LED Status LED

EC Firmware (FW) Authentication fail or not exit

EC FW is broken or not exit (Note1) OFF OFF

Authenticating/Recovering BMC/BIOS Images

Authenticating Images OFF OFF

Recovering BMC Active Flash

Blinks Blue

4 times per

second

Blinks Green

4 times per

second

Recovering BIOS Active Flash

Blinks Blue

4 times per

second

Blinks Green

4 times per

second

Authentication (AUTH) Pass

Recovering BIOS Active Flash OFF OFF

BMC : AUTH pass after doing recovery

BIOS : AUTH pass after doing recovery OFF OFF

BMC : AUTH pass after doing recovery

BIOS : AUTH pass OFF OFF

BMC : AUTH pass

BIOS : AUTH pass after doing recovery OFF OFF

Active Flash Authentication (AUTH) Fail

BMC : AUTH Fail(Note2)

Blinks Blue

1 time per

second

Blinks Green

1 time per second

System Appearance

- 19 -

BIOS : AUTH fail(Note2)

Blinks Blue

1 time per

second

Blinks Amber

1 time per second

BMC : AUTH fail after doing recovery(Note3)

Blinks Blue

2 times per

second

[ON OFF OFF]

Blinks Green

2 times per

second

[ON OFF OFF]

BIOS : AUTH fail after doing recovery(Note3)

Blinks Blue

2 times per

second

[ON OFF OFF]

Blinks Amber

2 times per

second

[ON OFF OFF]

Backup Flash Authentication Fail(Note4)

BMC : AUTH fail

Blinks Blue

2 times per

second

[ON OFF

ON OFF]

Blinks Green

2 times per

second

[ON OFF

ON OFF]

BIOS : AUTH fail

Blinks Blue

2 times per

second

[ON OFF

ON OFF]

Blinks Amber

2 times per

second

[ON OFF

ON OFF]

NOTE!

1. EC FW is broken or not exited result in Microchip CEC1702 cannot load EC FW for authentication.

2 (1) Authentication fail include below scenarios

Conguration table is missing or modied

Public key is missing or modied

Protected area or signature is modied

Flash empty

3. If active ash is still authentication failed after recovery sequence, Microchip CEC1702 stop the process

and showing LED behavior.

4. If backup flash authentication is failed cause by configuration table, public key or protected area is

broken. Microchip CEC1702 stop the process and showing LED behavior.

5. Front panel LED is controlled by BMC or Microchip CEC1702. Once Microchip CEC1702 is working(Auth

or recovery), the front panel LED is controlled by Microchip CEC1702 and vice versa.

System Appearance

- 20 -

2-4 Rear System LAN LEDs

No. Name Color Status Description

1. 1GbE

Speed LED

Yellow On 1 Gbps data rate

Green On 100 Mbps data rate

N/A Off 10 Mbps data rate

2.

1GbE

Link/

Activity

LED

Green

On Link between system and

network or no access

Blink Data transmission or receiving is occurring

N/A Off No data transmission or

receiving is occurring

21 1 2

Page is loading ...

Gigabyte R263-S33 User manual

Gigabyte R263-S33 User manual

Related papers

Other documents