Gigabyte G293-S46 User manual

G293-S46-AAM1

HPC/AI Server - 4th/5th Gen Intel® Xeon® Scalable - 2U DP 4 x PCIe Gen5 GPUs

User Manual

Rev. 1.0

Copyright

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of Giga Computing.

Changes to the specications and features in this manual may be made by Giga Computing

without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or

published in any form or by any means without Giga Computing's prior written permission.

Documentation Classications

In order to assist in the use of this product, Giga Computing provides the following types of documen-

tation:

 User Manual: detailed information & steps about the installation, conguration and use of this

product (e.g. motherboard, server barebones), covering hardware and BIOS.



User Guide: detailed information about the installation & use of an add-on hardware or

software component (e.g. BMC rmware, rail-kit) compatible with this product.

 Quick Installation Guide: a short guide with visual diagrams that you can reference easily for

installation purposes of this product (e.g. motherboard, server barebones).

Please see the support section of the online product page to check the current availability of these

documents.

For More Information

For related product specications, the latest rmware and software, and other information please visit our website at

http://www.gigabyte.com

For GIGABYTE distributors and resellers, additional sales & marketing materials are available from our reseller

portal: http://reseller.b2b.gigabyte.com

For further technical assistance, please contact your GIGABYTE representative or visit

https://esupport.gigabyte.com/ to create a new support ticket

For any general sales or marketing enquiries, you may also message GIGABYTE server directly by email:

server[email protected]

Conventions

The following conventions are used in this user's guide:

NOTE!

Gives bits and pieces of additional

information related to the current topic.

CAUTION!

Gives precautionary measures to

avoid possible hardware or software problems.

WARNING!

Alerts you to any damage that might

result from doing or not doing specic actions.

Server Warnings and Cautions

Before installing a server, be sure that you understand the following warnings and cautions.

WARNING!

To reduce the risk of electric shock or damage to the equipment:

• Do not disable the power cord grounding plug. The grounding plug is an important safety

feature.

• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all

times.

• Unplug all the power cords from the power supplies to disconnect power to the equipment.

•

• Shock Hazard! Disconnect all power supply cords before servicing.

• Do not route the power cord where it can be walked on or pinched by items placed against it.

Pay particular attention to the plug, electrical outlet, and the point where the cord extends from

the server.

WARNING!

To reduce the risk of personal injury from hot surfaces, allow the drives

and the internal system components to cool before touching them.

WARNING!

This server is equipped with high speed fans. Keep away from hazardous

moving fan blades during servicing.

WARNING!

This equipment is intended to be used in Restrict Access Location. The

access can only be gained by Skilled person.

Only authorized by well trained professional person can access the

restrict access location.

CAUTION!

• Do not operate the server for long periods with the access panel open or removed. Operat-

ing the server in this manner results in improper airow and improper cooling that can lead to

thermal damage.

• Danger of explosion if battery is incorrectly replaced.

• Replace only with the same or equivalent type recommended by the manufacturer.

• Dispose of used batteries according to the manufacturer’s instructions.

Electrostatic Discharge (ESD)

CAUTION!

ESD CAN DAMAGE DRIVES, BOARDS, AND OTHER PARTS. WE RECOMMEND THAT YOU

PERFORM ALL PROCEDURES AT AN ESD WORKSTATION. IF ONE IS NOT AVAILABLE,

PROVIDE SOME ESD PROTECTION BY WEARING AN ANTI-STATIC WRIST STRAP AT-

TACHED TO CHASSIS GROUND -- ANY UNPAINTED METAL SURFACE -- ON YOUR SERVER

WHEN HANDLING PARTS.

Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by

their edges without any component and pin touching. After removing a board from its protective

wrapper or from the system, place the board component side up on a grounded, static free sur-

face. Use a conductive foam pad if available but not the board wrapper. Do not slide board over

any surface.

System power on/o: To remove power from system, you must remove the system from

rack. Make sure the system is removed from the rack before opening the chassis, adding, or

removing any non hot-plug components.

Hazardous conditions, devices and cables: Hazardous electrical conditions may be

present on power, telephone, and communication cables. Turn off the system and discon-nect

the cables attached to the system before servicing it. Otherwise, personal injury or equipment

damage can result.

Electrostatic discharge (ESD) and ESD protection: ESD can damage drives,

boards, and other parts. We recommend that you perform all procedures in this chapter only at

an ESD workstation. If one is not available, provide some ESD protection by wearing an antistatic

wrist strap attached to chassis ground (any unpainted metal surface on the server) when handling

parts.

ESD and handling boards: Always handle boards carefully. They can be extremely

sensi-tive to electrostatic discharge (ESD). Hold boards only by their edges. After removing a

board from its protective wrapper or from the system, place the board component side up on a

grounded, static free surface. Use a conductive foam pad if available but not the board wrapper.

Do not slide board over any surface.

Installing or removing jumpers: A jumper is a small plastic encased conductor that slips

over two jumper pins. Some jumpers have a small tab on top that can be gripped with n-gertips

or with a pair of ne needle nosed pliers. If the jumpers do not have such a tab, take care when

using needle nosed pliers to remove or install a jumper; grip the narrow sides of the jumper with

the pliers, never the wide sides. Gripping the wide sides can dam-age the contacts inside the

jumper, causing intermittent problems with the function con-trolled by that jumper. Take care to

grip with, but not squeeze, the pliers or other tool used to remove a jumper, or the pins on the

board may bend or break.

CAUTION!

Risk of explosion if battery is replaced incorrectly or with an incorrect type. Replace the battery

only with the same or equivalent type recommended by the manufacturer. Dispose of used bat-

teries according to the manufacturer’s instructions.

- 7 -

Table of Contents

Chapter 1 Hardware Installation .....................................................................................9

1-1 Installation Precautions .................................................................................... 9

1-2 Product Specications .................................................................................... 10

1-3 System Block Diagram ................................................................................... 14

Chapter 2 System Appearance .....................................................................................15

2-1 Front View ...................................................................................................... 15

2-2 Rear View ....................................................................................................... 15

2-3 Front Panel LED and Buttons ........................................................................ 16

2-4 Rear System Button and LEDs ...................................................................... 17

2-5 Power Supply Unit (PSU) LED ....................................................................... 18

2-6 Hard Disk Drive LEDs .................................................................................... 19

Chapter 3 System Hardware Installation ......................................................................20

3-1 Removing Chassis Cover ............................................................................... 21

3-2 Removing and Installing the Fan Duct ........................................................... 22

3-3 Installing the CPU and Heat Sink ................................................................... 23

3-4 Installing the Memory ..................................................................................... 25

3-4-1 Eight Channel Memory Conguration .....................................................................25

3-4-2 Installing a Memory ...............................................................................................26

3-4-3 Processor and Memory Module Matrix Table .........................................................26

3-4-4 Memory Population Table .......................................................................................27

3-5 Installing the GPU Card ................................................................................. 28

3-6 Installing a PCI Express Card ........................................................................ 31

3-7 Installing the Hard Disk Drive ......................................................................... 35

3-8 Replacing the FAN Assembly ......................................................................... 36

3-9 Replacing the Power Supply .......................................................................... 40

Chapter 4 Motherboard Components ...........................................................................41

4-1 Motherboard Components ............................................................................. 41

4-2 Jumper Setting .............................................................................................. 43

4-3 Backplane Board Storage Connector ............................................................ 44

4-3-1 CBPE640 ................................................................................................................44

Chapter 5 BIOS Setup ..................................................................................................45

5-1 The Main Menu .............................................................................................. 47

5-2 Advanced Menu ............................................................................................. 50

5-2-1 Trusted Computing .................................................................................................51

- 8 -

5-2-2 Serial Port Console Redirection .............................................................................52

5-2-3 SIO Conguration ...................................................................................................56

5-2-4 PCI Subsystem Settings .........................................................................................57

5-2-5 USB Conguration ..................................................................................................59

5-2-6 Network Stack Conguration ..................................................................................60

5-2-7 Post Report Conguration ......................................................................................61

5-2-8 NVMe Conguration ...............................................................................................62

5-2-9 Chipset Conguration .............................................................................................63

5-2-10 Tls Auth Conguration ............................................................................................64

5-2-11 iSCSI Conguration ................................................................................................65

5-2-12 Broadcom BCM57416 Ethernet Network Connection ............................................66

5-2-13 VLAN Conguration ................................................................................................69

5-2-14 Driver Health ...........................................................................................................71

5-3 Chipset Menu ................................................................................................. 72

5-3-1 Processor Conguration .........................................................................................73

5-3-2 Common RefCode Conguration ...........................................................................76

5-3-3 UPI Conguration ...................................................................................................77

5-3-4 Memory Conguration ............................................................................................78

5-3-5 IIO Conguration ....................................................................................................81

5-3-6 Advanced Power Management Conguration ........................................................83

5-3-7 PCH Conguration ..................................................................................................85

5-3-8 Miscellaneous Conguration ..................................................................................88

5-3-9 Server ME Conguration ........................................................................................89

5-3-10 Runtime Error Logging Settings .............................................................................90

5-3-11 Power Policy ...........................................................................................................92

5-4 Server Management Menu ............................................................................. 94

5-4-1 System Event Log ..................................................................................................96

5-4-2 View FRU Information ............................................................................................97

5-4-3 BMC VLAN Conguration .......................................................................................98

5-4-4 BMC Network Conguration ...................................................................................99

5-4-5 IPv6 BMC Network Conguration .........................................................................100

5-5 Security Menu .............................................................................................. 101

5-5-1 Secure Boot .........................................................................................................102

5-6 Boot Menu .................................................................................................... 105

5-7 Save & Exit Menu ......................................................................................... 107

5-8 BIOS POST Beep code (AMI standard) ....................................................... 109

5-8-1 PEI Beep Codes ...................................................................................................109

5-8-2 DXE Beep Codes .................................................................................................109

- 9 -

Hardware Installation

1-1 Installation Precautions

The motherboard/system contain numerous delicate electronic circuits and components which

can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully

read the service guide and follow these procedures:

• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or

warranty sticker provided by your dealer. These stickers are required for warranty validation.

• Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

• When connecting hardware components to the internal connectors on the motherboard,

make sure they are connected tightly and securely.

• When handling the motherboard, avoid touching any metal leads or connectors.

• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

components such as a motherboard, CPU or memory. If you do not have an ESD wrist

strap, keep your hands dry and rst touch a metal object to eliminate static electricity.

•

Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

• Before unplugging the power supply cable from the motherboard, make sure the power

supply has been turned off.

• Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

• Before using the product, please verify that all cables and power connectors of your

hardware components are connected.

• To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

• Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

• Do not place the computer system on an uneven surface

.

• Do not place the computer system in a high-temperature environment.

• Turning on the computer power during the installation process can lead to damage to

system components as well as physical harm to the user.

• If you are uncertain about any installation steps or have a problem related to the use of the

product, please consult a certied computer technician.

Chapter 1 Hardware Installation

- 10 -

Hardware Installation

1-2 Product Specications

System

Dimension

2U

448mm (W) x 87.5mm (H) x 800mm (D)

CPU 5th Generation Intel® Xeon® Scalable Processors

4th Generation Intel® Xeon® Scalable Processors

Dual processor, CPU TDP up to 350W

NOTE: If only 1 CPU is installed, some PCIe or memory functions might be

unavailable

Socket 2 x LGA 4677

Socket E

Chipset Intel® C741 Chipset

Memory 16 x DIMM slots

DDR5 memory supported only

8-Channel memory architecture

RDIMM modules up to 96GB supported

3DS RDIMM modules up to 256GB supported

5th Gen Intel® Xeon®: Up to 5600MHz

4th Gen Intel® Xeon®: Up to 4800MHz

LAN 2 x 10Gb/s BASE-T LAN ports (Broadcom® BCM57416)

Supported NCSI function

1 x 10/100/1000 management LAN

Video Integrated in Aspeed® AST2600

2D Video Graphic Adapter with PCIe bus interface

1920x1200@60Hz 32bpp, DDR4 SDRAM

Storage 8 x 2.5" Gen5 NVMe/SATA/SAS hot-swappable bays, NVMe from CPU_1

SAS card is required for SAS devices support

SAS Supported via add-on SAS Card

RAID Intel® SATA RAID 0/1/10/5

NOTE:

We reserve the right to make any changes to the product specications and product-related

information without prior notice.

- 11 -

Hardware Installation

Expansion Slot Riser Card CRSG229 x 2:

- 4 x PCIe x16 (Gen5 x16) FHFL slots, from PS7101, for GPUs

Riser Card CRSG22A x 2:

- 4 x PCIe x16 (Gen5 x16) FHFL slots, from PS7101, for GPUs

Riser Card CRSG01F x 2:

- 1 x PCIe x16 (Gen5 x16) low-prole slot, from CPU_0

- 1 x PCIe x16 (Gen5 x16) low-prole slot, from CPU_1

- Maximum limitation of GPU card: 285mm (L) x 111.5mm (W) x 39.5mm (H)

- System is validated for population with a uniform GPU model

- Support is not provided for mixed GPU populations

- For the latest GPU cards QVL, please contact your GIGABYTE representative

Internal

Connectors

1 x TPM header

1 x VROC connector

Front Panel

LED/Buttons

1 x Power button with LED

1 x ID button with LED

2 x LAN activity LEDs

1 x HDD activity LED

1 x System status LED

1 x Reset button

Rear Panel I/O 2 x USB 3.2 Gen1

1 x VGA

2 x RJ45

1 x MLAN

1 x Power button with LED

1 x ID button with LED

1 x Reset button

1 x NMI button

1 x System status LED

Backplane I/O Backplane P/N: 9CBPE640NR-00

Speed and bandwidth: PCIe Gen5 x4 or SATA 6Gb/s or SAS 12Gb/s

TPM 1 x TPM header with SPI interface

Optional TPM2.0 kit: CTM010

- 12 -

Hardware Installation

Power Supply Dual 2200W (240V) 80 PLUS Titanium redundant power supply

AC Input:

- 100-127V~/ 15.5A, 50-60Hz

- 200-240V~/ 15.5A, 50-60Hz

DC Input: 240Vdc/ 15.5A

DC Output:

- Max 1000W/ 100-127V~

+ 12.2V/ 81A

+ 12Vsb/ 3A

- Max 2200W/ 200-240V~ or 240Vdc Input

+ 12.2V/ 180A

+ 12Vsb/ 3A

NOTE:

The system power supply requires C19 type power cord.

The power supply specications provided herein is for the default server conguration. Different

SKUs have different PSU specs, so please see the system rating label on the server for the

accurate PSU specication.

- 13 -

Hardware Installation

System

Management

Aspeed® AST2600 management controller

GIGABYTE Management Console (AMI MegaRAC SP-X) web interface



Dashboard

HTML5 KVM

Sensor Monitor (Voltage, RPM, Temperature, CPU Status …etc.)

Sensor Reading History Data

FRU Information

SEL Log in Linear Storage / Circular Storage Policy

Hardware Inventory

Fan Prole

System Firewall

Power Consumption

Power Control

LDAP / AD / RADIUS Support

Backup & Restore Conguration

Remote BIOS/BMC/CPLD Update

Event Log Filter

User Management

Media Redirection Settings

PAM Order Settings

SSL Settings

SMTP Settings

Operating

Properties

Operating temperature: 10°C to 35°C

Operating humidity: 8%-80% (non-condensing)

Non-operating temperature: -40°C to 60°C

Non-operating humidity: 20%-95% (non-condensing)

NOTE: Please contact Technical Support for more information about optimized GPU

system operating temperature

- 14 -

Hardware Installation

1-3 System Block Diagram

- 15 -

System Appearance

Chapter 2 System Appearance

2-1 Front View

• Please Go to Chapter 2-3 Front Panel LED and Buttons for detail description of function LEDs.

1

HDD #0

HDD #1

HDD #2

HDD #3

HDD #4

HDD #5

HDD #6

HDD #7

2-2 Rear View

No. Description No. Description

2. VGA Port 7. System Status LED

3. 10/100/1000 Server Management LAN Port 8. 10GbE LAN Port x 2

4. Power Button with LED 9. USB 3.0 Port x 2

5. ID Button 10. NMI Button

6. Reset Button

2 3 4 5 6 7

9

8

10

Power Supply

(PSU1)

Power Supply

(PSU2)

No. Description

1. Front Panel LED and Buttons

NOTE! Green HDD Latch Supports NVMe

- 16 -

System Appearance

2-3 Front Panel LED and Buttons

1

2

3

4

5

6

7

No. Name Color Status Description

1. Power button

with LED

Green On System is powered on

N/A Off System is not powered on or in ACPI S5 state (power off)

2. ID Button Press the button to activate system identication

3/4. LAN 1/2 Active/

Link LEDs

Green Solid On Link between system and network or no access.

Green Blink Data trasmission or receiving is occuring

N/A Off No data transmission or receiving is occuring

5. HDD Status

LED

Green On HDD locate

Blink HDD access

Amber On HDD fault

Green/

Amber Blink HDD rebuilding

N/A Off No HDD access or no HDD fault.

6. System

Status LED

Green Solid On System is operating normally.

Amber

Solid On

Critical condition, may indicate:

System fan failure

System temperature

Blink

Non-critical condition, may indicate:

Redundant power module failure

Temperature and voltage issue

Chassis intrusion

N/A Off

System is not ready, may indicate:

POST error

NMI error

Processor or terminator missing

7. Reset Button Press the button to reset the system.

- 17 -

System Appearance

2-4 Rear System Button and LEDs

No. Name Color Status Description

1. Power Button

with LED

Green On System is powered on

N/A Off System is not powered on or in ACPI S5 state (power off)

2. ID Button Press the button to activate system identication

3. Reset Button Press the button to reset the system.

4. NMI button

Press the button server generates a NMI to the processor

if the multiple-bit ECC errors occur, which effectively halt

the server.

5. System

Status LED

Green Solid On System is operating normally.

Amber

Solid On

Critical condition, may indicate:

System fan failure

System temperature

Blink

Non-critical condition, may indicate:

Redundant power module failure

Temperature and voltage issue

Chassis intrusion

N/A Off

System is not ready, may indicate:

POST error

NMI error

Processor or terminator missing

6. 10GbE

Speed LED

Green On 10 Gbps data rate

Yellow On 5Gbps, 2.5Gbps, 1Gbps data rate

N/A Off 100 Mbps data rate

7. 10GbE Link /

Activity LED

Green On Link between system and network or no access

Blink Data transmission or reception is occurring.

N/A Off No data transmission or reception is occurring.

8. 1GbE Speed

LED

Yellow On 1 Gbps data rate

Green On 100 Mbps data rate

N/A Off 10 Mbps data rate

9. 1GbE Link /

Activity LED

Green On Link between system and network or no access

Blink Data transmission or reception is occurring.

N/A Off No data transmission or reception is occurring.

1 2

3

4

5

6

7

6

7

8 9

- 18 -

System Appearance

2-5 Power Supply Unit (PSU) LED

PSU LED

State Description

OFF No AC power to all power supplies

1Hz Green Blinking AC present / only standby on / Cold redundant mode

2Hz Green Blinking Power supply rmware updating mode

Amber

AC cord unplugged or AC power lost; with a second

power supply in parallel still with AC input power

Power supply critical event causing shut down:

failure, OCP, OVP, fan failure and UVP

1Hz Amber Blinking

Power supply warning events where the

power supply continues to operate:

high temp, high power, high current and slow fan

- 19 -

System Appearance

2-6 Hard Disk Drive LEDs

/(' /('

Disk LED

(LED on

Back Panel)

Removed HDD Slot

(LED on Back Panel)

Disk LED

Removed HDD Slot

RAID SKU

No RAID configuration

(via PCH, HBA)

RAID configuration

(via HW RAID Card or

SW RAID Card)

HDD

Access

HDD Present

(No Access)

BLINK (*2)

OFF

--

OFF

(Low Speed: 2 Hz)

(*3)

Rebuilding

HDD Fault

OFF

ON

OFF

ON

OFF

Locate

Amber

Green ON(*1)

ON

OFF

ON(*1)

OFF

Green

Amber

Green

ON(*1)Green

OFFAmber

Amber OFF

LED1

NOTE:

*1: Depends on HBA/Utility Spec.

*2: Blink cycle depends on HDD's activity signal.

*3: If HDD is pulled out during rebuilding, the disk status of this HDD is regarded as faulty.

LED 2 HDD Present No HDD

Green ON OFF

- 20 -

System Hardware Installation

Pre-installation Instructions

Computer components and electronic circuit boards can be damaged by discharges of static

electricity. Working on computers that are still connected to a power supply can be extremely

dangerous. Follow the simple guidelines below to avoid damage to your computer or injury to

yourself.

• Always disconnect the computer from the power outlet whenever you are working inside the

computer case.

• If possible, wear a grounded wrist strap when you are working inside the computer case.

Alternatively, discharge any static electricity by touching the bare metal system of the computer

case, or the bare metal body of any other grounded appliance.

• Hold electronic circuit boards by the edges only. Do not touch the components on the board

unless it is necessary to do so. Do not ex or stress the circuit board.

• Leave all components inside the static-proof packaging until you are ready to use the component

for the installation.

Chapter 3 System Hardware Installation

Page is loading ...

Gigabyte G293-S46 User manual

Gigabyte G293-S46 User manual

Related papers