Page is loading ...
SHT‐35QuickStartGuidev1.0
2/7
. ⅠIntroduction
1 Receiver
2 Indicator LED
3 Scan Key
4 ESC(Back Function)
5 ENT(Enter Function)
6 Blue FN(Reserved)
7 Win (Enter to Desktop)
8 Orange FN(Switch Input Method)
9 Power Key
10 BKSP(Delete Character)
11 Shift Key
12 TAB Key
13 Microphone
14 Scan Engine Window
15 Color Camera
16 Scan Key
17 Rear Speaker
18 USB Interface(Charge or Connect to
PC)
19 Volume Button
SHT‐35QuickStartGuidev1.0
3/7
Ⅱ. Out of the Box
Verify that the carton contains the following items:
Sinocan SHT-35 Mobile Terminal
Battery Pack(3.7V Li-ion)
Power Adaptor
USB Cable
Touch Stylus
Lanyard
Note:If you ordered accessories for your terminal, verify that they are included with the
order.
Ⅲ. Install Battery Pack
The SHT-35 terminal is shipped with the battery packaged separate from the
terminal. Follow the steps bellow to install the main battery.
Ensure all components are dry prior to placing the battery in the terminal. Mating
wet components may cause damage not covered by the warranty.
1. Release the hook securing the hand strap to the back panel of the terminal
2. Remove the battery door by lifting up the latches near the base of the
battery door
3. Insert the battery into the battery well
SHT‐35QuickStartGuidev1.0
4/7
4. Replace the battery door. Apply pressure to engage the door latch. The
battery door must be installed prior to powering the unit
5. Reattach the hand strap
6. Connect the terminal to charging peripherals to charge the main battery
pack
We recommend use of Sinocan Li-ion battery packs. Use of any non-Sinocan
battery may result in damage not covered by the warranty.
Ⅳ. Charging the Terminal
Warning! Sinocan Charging peripherals are not designed for use in hazardous
locations.
Ensure all components are dry prior to placing the battery in the terminal. Mating
wet components may cause damage not covered by the warranty.
You can charge for the terminal by USB cable connecting to PC or power
supply.
To PC’s USB Connector
SHT‐35QuickStartGuidev1.0
5/7
Ⅴ. Installing Cards
A. Installing a Memory Card
Note: Format all microSD/SDHC cards before initial use.
1. Press the Power Key 3-seconds to make the terminal powered off status
2. Release the hand strap hook near the scanner on the back panel of the
terminal, and then remove the battery door and battery
3. Push SIM card’s door toward right direction to unlock, and then lift the
door to expose the socket
4. The same way to lift the memory card’s door to expose the socket
5. Slide the micro SD/SDHC card into the door of the socket
Note: Make sure the interface on the memory card is connected to the interface in the
socket, align the notch on the card with the notch of the socket.
6. Close and lock the door
B. Installing a SIM Card
Reference to installing a memory card, Slide the GSM card into the SIM
card’s door of the socket
SHT‐35QuickStartGuidev1.0
6/7
Ⅵ. Home Screen and Unlock Screen
Ⅶ. Connect PC
1. Install Active Sync Software on your PC at first
Download: http://www.sinocan.com.cn/Drivers/MobilePOS/Active_Sync_v4.5.rar
2. Connect PC through USB cable, then choose ActiveSync mode
Note: For application software development, please reference to our Demo and Libraries,
please download http://www.sinocan.com.cn/Drivers/MobilePOS/SHT35-SDK.rar
Charging
Status
GSM Card Phone
Function
Sound Status
SHT‐35QuickStartGuidev1.0
7/7
Ⅷ.Specification
Model SHT-35
CPU ARM 9, 533MHz
OS Window Mobile 6.5, English
Memory & SDRAM 256M RAM/512M Flash
Display 3.5",HVGA 320x480, Resistive Touch Panel
Keypad and Button Numeric Keypad with 3 side Button
Camera Camera 3.0M Pixel Camera, Auto Focus With LED Flash
RF-WWAN 900/1800MHz GSM/GPRS
(*Option 3G 800MHz EVDO)
RF-WLAN 802.11b/g WLAN
RF-BT Bluetooth V2.0
RF-GPS Hardware GPS and A-GPS Supported
Audio Speaker/Receiver/Microphone
Battery 3.7V 3000mAh Battery, Can Work 10 Hours or Above
Barcode Engine Embedded 1D Laser Barcode Scan Engine
(*Option 2D CCD Barcode Scanner)
Size 160(L) x 70(W) x 30(H)mm
Weight <250g
Environmental
Drop test 3 feet
ESD 8KV(CoNTACT)&15KV(Air)
Operating Temperature:-10~50 Degree
Storage Temperature:-20~60 Degree
Battery charging temperature:0~45 Degree
Humidity:0%~95% non-condensing
RoHS compliant
IP54
Accessories
Power Supply x 1
USB Cable x 1
Touch Stylus x 1
Battery x 1
Screen Film x 1
Lanyard Strap x 1
Portable Cover (*Option)
Backup Battery(*Option)
Portable Receipt Thermal Printer(*Option)
/
