Baso RSDA Series Installation guide

Brand
Baso
Model
RSDA Series
Type
Installation guide

Baso RSDA Series is a replacement solenoid coil designed for use with BASO® Gas Products. It is a versatile and reliable component that offers a range of features to meet various needs. The RSDA Series coil is available in multiple voltage options, including 12 VDC, 25 VDC, 25 VAC, 120 VAC, and 240 VAC. It delivers efficient power consumption with VA ratings ranging from 10.5 to 11.5 VA, ensuring optimal performance. The coil's compatibility with different tab configurations, such as 2-tab and 3-tab, enhances its versatility.

Baso RSDA Series is a replacement solenoid coil designed for use with BASO® Gas Products. It is a versatile and reliable component that offers a range of features to meet various needs. The RSDA Series coil is available in multiple voltage options, including 12 VDC, 25 VDC, 25 VAC, 120 VAC, and 240 VAC. It delivers efficient power consumption with VA ratings ranging from 10.5 to 11.5 VA, ensuring optimal performance. The coil's compatibility with different tab configurations, such as 2-tab and 3-tab, enhances its versatility.

Installation Instructions RSDA95A
Issue Date March 12, 2020
RSDA95A Replacement Solenoid Coil
© 2020 BASO Gas Products 1
Part No. BASO-INS-RSDA95A, Rev. C www.baso.com
RSDA95A Replacement Solenoid Coil
Installation
IMPORTANT: These instructions are intended as
a guide for qualified personnel installing or servicing
BASO® Gas Products. Carefully follow all instructions in
this bulletin and all instructions on the appliance. Limit
repairs, adjustments, and servicing to the operations listed
in this bulletin or on the appliance.
!
WARNING: Risk of Electric Shock.
Disconnect the power supply before wiring connections
are made to avoid possible electric shock or damage to
equipment.
!
WARNING: Risk of Equipment Damage. Label
all wires prior to disconnection when servicing valves.
Wiring errors can cause improper and dangerous
operation. Verify proper operation after servicing.
Only a trained service professional should perform this
procedure. To replace the coil:
1. Disconnect the power supply to the valve.
2. Label and remove all wires connected to the coil.
3. Remove the existing solenoid. (Optional Attachments)
a. Locknut: Using a wrench, loosen the locknut at the
top of the coil and remove both the nut and washer.
b. E-ring: Use a flat blade screw driver and remove
the E-ring.
Rotate
360
Figure 1: Replacement Solenoid Coil Procedure
4. Carefully lift the coil off the solenoid guide.
!
WARNING: Risk of Shock.
Do not apply undue force on the solenoid guide during
removal or replacement. The plunger is housed within this
guide and any distortion could tighten around the plunger
and prevent the valve from closing.
5. Place the new replacement coil on the solenoid guide.
6. a. Replace the washer and locknut if the solenoid guide
uses the threaded stud.
b. Carefully tighten the locknut. Do not over tighten.
Tighten the locknut to 25 lbs – in (2.82 N.m)
7. Replace the E-ring if the solenoid guide uses the slotted
head. Use a channel lock pliers and squeeze the E-ring
back in place. Ensure the cup part of the E-ring is up
before assembly.
8. Connect all wires according to the labels applied in
Step 2. In some cases, the terminals are rotated
90 degrees from the previous version coil’s orientation is
not significant.
9. Turn on the power to the valve.
10. Run the valve through several cycles of operation and
check that all functions are satisfactory.
Repairs and Replacement
Table 1: Replacement Solenoid Coil
Part Number
(Coil Color) Description
RSDA95A-12
(Red) 12 VDC; 2-tab 10.5 VA Coil
RSDA95A-25V
(Green) 25 VDC; 3-tab 11.5 VA Coil
RSDA95A-25
(Green) 25 VAC; 50/60 Hz; 3-tab 10.5 VA Coil
RSDA95A-25A
(Green) 25 VAC; 50/60 Hz; 2-tab 10.5 VA Coil
RSDA95A-120
(Blue) 120 VAC; 60/60 Hz; 3-tab 10.5 VA
Coil
RSDA95A-240
(Black) 240VAC; 50/60 Hz; 3-tab 10.5 VA
Coil
450 East Horseshoe Road
PO Box 170
Watertown, WI 53094 www.baso.com
1-877-227-6427 (1-877-BASOGAS) Printed in U.S.A.
  • Page 1 1

Baso RSDA Series Installation guide

Brand
Baso
Model
RSDA Series
Type
Installation guide

Baso RSDA Series is a replacement solenoid coil designed for use with BASO® Gas Products. It is a versatile and reliable component that offers a range of features to meet various needs. The RSDA Series coil is available in multiple voltage options, including 12 VDC, 25 VDC, 25 VAC, 120 VAC, and 240 VAC. It delivers efficient power consumption with VA ratings ranging from 10.5 to 11.5 VA, ensuring optimal performance. The coil's compatibility with different tab configurations, such as 2-tab and 3-tab, enhances its versatility.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents