Home Theater Master MX-500TM Specification

Home Theater Master@

LCD Screen

Preprogrammed and Learning

Remote Control

1, Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3

2. Batteries .

.._........._.......................................................................................

4

A. Battery Installation

B. Battery Life

3. Summary of Operations . . . . .

.._.......................................................

5

A. Description of Devices

B. Preprogrammed Codes

C. Learning from Other Remote Controls

D. Macro Operations

E. Favorite Channel Buttons

F. Punch Through Operations

G. Editing LCD Text

H. Cloning the MX-500TM

I. All Other Operations

J. LCD Screens and Button Layout

K. System Settings

4. Programming the Remote to Control Your

Components . . .

.._......................................................................................

10

A. Preprogrammed Codes

1. Three-Digit Code Number

2. Auto Scan Method

B. Learning Method

1. Programming Function Buttons

2. Programming Ten Device Buttons

5. JJfbogramming Favorite Channels .

.._....................................

18

6.

Programming Macro Buttons ..,....__........................................

20

1. Ml - M3, Power and System Off Buttons

2. Ten Device Buttons

7. Programming Punch Through Operations ............‘... 23

8. Erasing Existing Programming

..,....._....................................

24

A. Erasing Learned Buttons

B. Erasing Favorite Channel Buttons

C. Erasing Macro Functions

1. Ml - M3, Power and System Off Buttons

2. Ten Device Buttons

D. Erasing Punch Through Functions

9.

LCD Button

Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28

A. Create or Edit Text on Function Buttons

B. Create or Edit Text on Device Buttons

C. Create or Edit Text on Favorite Channel Buttons

10. Recalling the Preprogrammed Three-Digit Code

Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

11.

Setting

Back

Light

._.....__,......,_.......................................,................

31

12.

Cloning MX-SO()TM 32

13.

Adjustment of LCD contrast

33

14. Caution in

Handling

LCD Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

15. Low Battery Message 34

16. Memory Lock . . . . .

..__......._..................................................................

34

17. Warranty 35

18. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

19. Appendix 36

A. List of Preprogrammed LCD Texts by Device

B. Three-Digit Preprogrammed Code Table

Congratulations! You have purchased one of the most

sophisticated remote control on the market. The MX-

500TM has been designed to provide a new standard in

remote control and infrared technology offering a very

powerful and flexible preprogrammed, learning, menu-

driven product.

With the MX-SOOTM you have the option of programming

the unit for up to ten home entertainment and home

automation components by using either the preprogrammed

code library in the remote control, by teaching up to 530

commands into MX-500TM from your original remote

controls, or a combination of both methods.

The MX-500TM has many additional operating features to

add convenience and enjoyment to the operation of your

home entertainment system including the ability to create

your own descriptions of the component buttons on the

LCD, the ability to learn 530 commands from your original

remote controls, various macro operations program, 50

favorite channels buttons, and punch-through operations

for volume control, channel and transport buttons.

Setting up the MX-500 TM to operate your components is

easy and simple. Please follow the instructions in the

manual and retain the manual for future reference. In the

event the manual is lost or misplaced, a replacement copy

can be found at the Home Theater Master website:

httn://www.hometheatermaster.com

For any questions or comments about the MX-500TM, please

contact us at Universal Remote Control, Inc., 500

Mamaroneck Avenue, Harrison, NY 10528 at 914-835-4484

or e-mail us: [email protected] Regular customer service

hours are 9:00 AM to 6:00 PM EST, Monday - Friday.

A. Battery Installation

Before the remote control can be used, the supplied

batteries need to be installed. First, unsnap the battery

cover on the back of the unit and install the four AAA

batteries inside the battery compartment as shown. Make

sure the batteries line up with the (+) and (-) markings.

Improper installation could damage the remote control.

When you’re done, slide the battery cover back on. The

remote control starts up automatically and the default

device components will appear on the LCD.

B. Battery Life

Under normal operating conditions, the batteries

supplied with the remote control will last approximately

six months. If the batteries are running low, you will

notice reduced range from the remote control,

commands that are not sent properly, or are not sent at

all. You may also notice the backlighting of the LCD

screen and the button is diminished.

Should any of these occur, replace the batteries

immediately. To ensure proper performance of the unit,

only use new alkaline batteries.

The remote control will retain the commands and

settings in its memory even after the batteries are low or

become discharged. See Memory Lock on page 34.

Please replace the worn batteries with a fresh set as soon

as possible.

A. Description of Devices

The MX-5OOTM is designed to operate up to ten components

on the market including Audio Receivers, Cable and

Satellite Boxes, TV, DVD (LD),VCRl, VCR2, CD,

Tape and AUX. However, each of the device buttons

and corresponding functions can be changed to meet

your individual requirements. Almost any device that

uses infrared commands can be controlled by the MX-

500TM, including Home Automation, Personal

computers and more.

Tip) The auxiliary function could be used to operate

lighting controls or the second VCR could be changed

to operate a second TK

Each device button on the main screen contains two sub-

pages of commands and you can change the name of any

LCD button using up to five alphabet characters and

numbers to customize the unit to fit your audio/video

components. Please refer to the LCD Button Editing on

page 28 for additional details.

B. Pre-programmed Codes

The MX-5OOTM comes with preprogrammed codes for

practically all the major audio and video equipment on

the market. You can set-up and operate all of your

components with the MX-500TM simply by punching in

the three-digit code number assigned to your brand of

component.

The code numbers for the various brands of components

are listed in the back of this instruction manual. Please

refer to the programming instructions shown on page 10

for details.

C. Learning From Other Remote Controls

The MX-500TM can learn codes from your original

remote controls. There are 26 LCD screens in the remote

control and all the functional buttons as well as ten

device buttons on the main menu screen can be taught.

In addition, there are 31 rubber buttons and a joystick

that can be taught for each of the ten devices. As a

whole, you can teach up to 530 new functions into the

remote control. Please refer to page 15 in the instruction

manual for details.

D. Macro Operations

The remote control is capable of sending out a series of

commands with one button press. Any function available

on your original remote control or in the pre-programmed

database can be added to a macro button to completely

automate what you would normally do by pushing

buttons one at a time. It can be as simple as “Turning on

your TV and Cable Box, turning the TV to the appropriate

channel for operation with the Cable Box and changing

the Cable Box channel to your favorite morning news

channel”. Or the macros can be configured to “Power On

your TV, DVD player and receiver, change to the

appropriate inputs and outputs, dim your lights and start

the movie playing”. It can be simple or as comprehensive

as you want it to be.

There are two types of macro buttons you can use for

macro operations:

Ml, M2, M3, Power and System Off Buttons

Each of these five buttons are designed to send out up

to 20 series of commands you program into the

buttons. Each one is commonly used to turn on and

turn off all of your A/V components with one button

press, but can be programmed with whatever macro

you desire.

Ten Device Buttons

There are ten device buttons and each of these device

buttons can send out up to 20 programmed commands

when pressed for more than two seconds. It is

typically used in sending out audio input codes so that

the audio receiver will make an automatic input switch

when you press the respective device button on the

remote control, but can be programmed with whatever

macro you desire.

E. Favorite Channel Buttons

You can create up to 50 favorite channel buttons in the

remote control by programming the most frequently

watched channel numbers into these buttons. Each of

these buttons can send out up to 10 commands.

Please refer to page 18 of the manual for programming

the Favorite Channel Programming.

F. Punch Through Operations

The MX-500TM can be setup to operate audio component

volume control buttons (VOLUME UP and DOWN and

MUTE) while all the other buttons control other

equipment. You can also set up the remote to operate

channel control and transport functions (PLAY, STOP,

REWIND, FAST FORWARD, SKIP-, SKIP+, PAUSE

and Record buttons) from VCR, DVD, LD, CD or any

other mode while all other buttons in the remote control

are controlling different components.

Please refer to page 23 in the manual for details.

G. Editing LCD Text

You can create your own text on each of the twenty-six

LCD screens.

Please refer to page 28 in the manual for details.

H. Cloning the MX-500TM

The MX-500TM is capable of sending and receiving all

the programmed codes, text on the LCD and operations

from one MX-500TM to another MX-500TM. Please refer

to page 32 in the manual for details.

I. All Other Operations

You can set the duration of the backlight on time and

LCD contrast. Please refer to page 33 and 35 in the

manual for details.

J. LCD Screen and Button Layout

(i) Displays the name of the device selected.

B System off(Power off)

0 Displays page number.

a Displays the device and function names.

@ LIGHT button.

m MACRO buttons.

0 MAIN DEVICE menu button.

@ LCD Page change button.

a POWER

0 MUTE

m VOLUME

0 CHANNEL

0 Previous channel button.

@ TRANSPORT functions(PLAY, STOP, REWIND and FF)

for VCR, CD and DVD etc.

m JOYSTICK button(UP, DOWN, LEFT, RIGHT and ENTER)

to move the cursor and enter the selection by pushing down

the joystick.

0 ENTER

m DISPLAY

K. System Settings

All programming is done by first entering the SYSTEM

SETTING mode in the remote control. Press both the

R buttons simultaneously for three

seconds to enter the SYSTEM SETTING mode.

Press any of the ten buttons associated with the descriptions

written on the LCD. You can exit the Set Up mode by

simply pressing the button.

You can program the MX-500TM to make it compatible

with your components by following either the pre-

programmed method instructions or by teaching it with

your original remote controls.

A. Using Pre-programmed Codes

You can program the MX-500TM to make it compatible with

your components by using the pre-programmed method.

1. Three-Digit Code Number

1. Turn on the component you wish to program.

Tip) Zf your component has a discrete Power ON and

OFF button, please do not yurn on the component

manually.

2. Go to the program setting mode by pressing both

MN and ALTAR buttons simultaneously for

three seconds.

3. Select the P-PRO button next to the LCD screen.

4. Press the device you wish to program. (E.g. To

program TV, press the TV button).

5. Select the device from which the appropriate

three-digit code number table will be selected.

(E.g. If it is the TV code table, press the TV device

button).

6. Point the remote control toward the component

and enter the three-digit code number you selected

for your component from the code table provided

on page 41 - 54. (Please enter the code number

within 20 seconds of programming). If there is more

than one code number assigned to your brand, try

the one code number at a time until you find the

right code number. (If you enter the right code

number, the component will turn off right after you

entered the correct number).

7. Confirm that it is the right code by pressing

Power button. After you have confirmed that the

right code is entered, save the code by pressing the

SAVE button on LCD.

8. Exit from preprogramming mode by pressing

the button and then exit from SET UP mode

by pressing the button once again.

9. Confirm yo entered the right code

number that matches your component by pressing

other functional buttons. If any of the buttons fail to

operate, as they should, please repeat from Step 1.

10. Continue to program other components by

repeating from Step 1 above.

2. Auto Scan with Three Digit Number

You can also program your remote control by sending

out series of Power Off commands for different brands

stored in the library by using the following steps.

1. Manually turn on the component you plan to

operate.

Tip) If your component has a discrete Power ON and

OFF button, please do not yurn on the component

manually.

2. Go to program setting m

control by pressing both th

buttons simultaneously for three seconds.

3. Select the ~-~~~ button next to the LCD screen.

4. Press the device you wish to program.

(E.g. To program TV, press the TV button).

5. Select the device from which the scanned code

table will be selected. (E.g. If it is the TV code

table, press the TV device button).

6. Point the remote control toward the component

and press either the 0rD button on the

LCD. (It will send out the series of Power codes

when the button is kept pressed and the,code

number that are being sent are shown on the LCD).

If the right code number is sent, the component will

turn off right after the code number is transmitted.

7. Release the UP or

pressing as soon as th

8. Confirm that it is the right code by pressing

Power button. After the confirmation that the

code is entered, save the code by pressing the

button on the LCD. Later you may want to try other

code numbers for your component to see which one

includes the most functions appropriate for your device.

9. Exit from Preprogrammed mode by pressing the

AEN button and then exit from SET UP mode by

pressing the ~A~ button once again.

10. Confirm that you entered the right code number

that matches your component by pressing other

functional buttons. If any of the buttons do not

operate as they should, please repeat from Step 1.

11. Continue to program other components by

repeating from Step 1 above.

B. Learning From Other Remote Controls

You can program the MX-500TM to operate a component

by teaching the commands from your original remote

control to device buttons on the main screen menu, 20

buttons on 2 pages of the LCD per device, 31 rubber

buttons and the joystick located in the middle of the

remote control. The MX-5OOTM learns these commands

by receiving infrared signals directly from your existing

remote controls. The MX-500TM receives these signals

through its learning eye, located at the top of the unit.

Apart from the PAGE, MAIN, FAV buttons and Ml - M3

buttons which cannot be taught, the MX-500TM has the

capability of learning up to 530 commands.

Tip) Commonly usedfunction buttons include the two

pages of sub-commands within each of the 10 devices,

channel up and down, volume up and down, menu,

guide, exit, info, O-9 and joystick.

Points to Remember

If the remote control fails to learn a function after the

first try:

l Keep the remotes stable by placing them on a flat surface.

l Make sure the original remote is pointed at the

learning eye at the top end of the case.

l Make sure the original remote’s batteries aren’t low.

l Try again. Sometimes the second or third attempt works.

l Try varying the distance between the remotes until

you find an optimal distance where the codes are

learned on the first or second try.

1. Programming Function Buttons

1. Go to the program setting mode by pressing both

buttons simultaneously for

three seconds.

2. Press the LEA

3. Select the ish to program.

4. Press the button on the MX-500TM you wish to

program and place your original remote control

head to head with the MX-5OOTM about 2 inches

apart on a flat surface as illustrated below.

5. Press the button on your original remote control

you wish to program into the MX-500TM. Once the

MX-SOOTM has received the signal, the MX-500TM

will flash “Good” on the LCD screen, indicating it

learned the code correctly. If it flashes “Fail”, repeat

from Step 4 until it learns successfully. (Please

enter the code signal within 20 seconds of

programming).

6. Once you complete the programming and wish

to exit the leaning mode, press the I%$ utton.

Exit from SET UP mode by pressing t

button once again.

2. Programming the Ten Device Buttons

1. Go to the program setting mode by pressing both

the IN and buttons simultaneously for

three seconds.

4. Press any of the ten device buttons you wish to

program into the MX-500rM and place your original

remote control head to head with the MX-500TM

about 2 inches apart on a flat surface.

5. Press the button on your original remote control

you wish to program into the MX-500TM. Once the

MX-500TM has received the signal, the MX-500TM

will flash “Good” on the LCD screen, indicating it

learned the code correctly. If it flashes “Fail”, repeat

from Step 4 until it learns successfully. (Please

enter the code signal within 20 seconds of

programming).

6. Once you complete the programming and wish

to exit the leaning mode, press the

Exit from SET UP mode by pressing the

button once again.

You can create and program up to 50 Favorite Channel

Buttons and each favorite channel button can send out up

to 10 commands with one button press.

1. Go to the pro,gram setting mode by pressing both the

M and B R buttons simultaneously for three

seconds.

2. Press the FAV Button on the LCD.

3. Press the appropriate device button from which the

channel number will be selected.

M!:ll...l 1 E HE:l-F

4. Go to one of the five I+$ZD pages by pressing the

FAV(or PAGE) button. Press the button you will be

assigning to the favorite channel and enter the channel

number, power, Display and Enter commands you wish

to store in the FAVORITE channel button. You can store

up to 10 commands.

Tip) If you pressed a wrong channel numbel; please

move the cursor by using left or right button of the

joystick and then press the correct channel number:

5. Press the favorite channel button you selected in Step

4 again to store the channel you programmed.

Page is loading ...

Home Theater Master MX-500TM Specification

This manual is also suitable for

Home Theater Master MX-500TM Specification

Related papers

Other documents