Lorex L19LD800 Series Quick start guide

Lorex
Brand
Lorex
Model
L19LD800 Series
Type
Quick start guide
BUSINESS & HOME SECURITY
INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. AS OUR PRODUCTS ARE SUBJECT TO CONTINUOUS IMPROVEMENT,
LOREX TECHNOLOGY INC. AND OUR SUBSIDIARIES RESERVE THE RIGHT TO MODIFY PRODUCT DESIGN, SPECIFICATIONS AND PRICES, WITHOUT
NOTICE AND WITHOUT INCURRING ANY OBLIGATION. E&OE © 2007 LOREX. ALL RIGHTS RESERVED.
L19LD800 Series
WWW.LOREXCCTV.COM
QUICK START GUIDE R2
Page: 2
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
Page: 2
PACKAGE CONTENTS AND
INSTALLATION GUIDE:
ATTENTION:
Broadband Router
and Computers are
required for local and
remote monitoring
(not included).
INSTRUCTIONS:
For detailed setup
information, please
refer to your User’s
manual.
SOFTWARE
REQUIREMENTS:
For Lorex Client 3.0
Software requirements,
please refer to the
Software User’s manual.
System Contents:
1 - 19” 8 Channel LCD Monitor with pre-installed HDD*
4 - High Res. Color Cameras*
4 - 100 ft (30M) Extension Cables*
4 - Camera Stands with Mounting Screws*
1 - 10 ft Ethernet Cable
1 - Remote Control
2 - AAA Batteries
1 - Power Adaptor (for monitor)
1 - Lorex Client Software CD
1 - User’s Manual
1 - Software Manual
1 - Quick Start Guide
* Camera configuration and HDD (hard disk drive) capacity may vary
by model. BNC Cameras require individual power adaptors. Check
your package for specific content information.
INSTALLATION GUIDE
Skill Level
Intermediate
easy advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Skill Level
Intermediate
easy advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time Tools Skills - Easy
Under 20 Minutes* Hand Tools Plug & Play connectors,
On screen set up
* Installation time may vary based on
application and camera cabling
STEP 1 STEP 2
Skill Level
Intermediate
easy advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time Skills - Intermediate
Plug & Play connectors,
On screen set up
Under 30 Minutes*
* Installation time may
vary based on application
Skill Level
Intermediate
easy advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Hardware
Computer &
Router*
STEP 3
Skill Level
Intermediate
easy advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Skill Level
Intermediate
easy advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
Time Hardware Skills - Advanced
60 Minutes Computer &
Router*
Basic Computer
Skills, Router Port
Forwarding
* Installation time may vary
based on application
Skill Level
Intermediate
easy advanced
Time
under 30 minutesunder 15 minutes under 60 minutes
Hand Tools Hardware
Router
Hi Speed
over 60 minutes
* Minimum System Requirement: Windows XP, Pentium IV,
256MB Ram (512MB Recommended), 200MB Storage, High
Speed Internet, DSL or Cable Modem
Check Pages
14 - 15
Page: 2
Page: 2Page: 3
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
DEVICE CONNECTIONS (Stand Removed)
2a
Screws
Lay the monitor facing down on a soft surface. Make sure
to protect the screen from sharp objects.
OPTIONAL - LOCATE MONITOR CONNECTIONS
STEP 1 - SET UP YOUR MONITOR FIRST
2
The system has an efficient back panel control that
provides a cable management solution.
By design the connectors are not easily accessible, in
order to secure the connections.
It is recommended to remove the stand for initial set-up
by simpy unscrewing four screws with a standard screw
driver.
OPTIONAL - REMOVE MONITOR STAND
The stand comes with a built in cable channel to easily organize
and conceal wiring. Connect the Power Cable, Cameras, Ethernet
Cable and any Alarm Devices to the System by running the cables
through the hole in the stand before connecting to the
Observation System.
NOTE: Your system can be mounted on a wall using a VESA
standard mounting bracket (not included).
DEVICE CONNECTIONS
Tilt the monitor (40˚) to allow for easier access to the
connectors.
TILT MONITOR
1
3
Efficient back
panel provides
a solution for
neat cable
management.
Page: 4
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
Page: 4
STEP 1 - SET UP YOUR MONITOR FIRST
Your system includes 4 high resolution 6 PIN DIN cameras.
CONNECT CAMERAS TO THE MONITOR
Connect one end of the ethernet cable to one of the router’s (not
included) LAN PORTS and the other end to the Monitor’s Network Port
located at the bottom of the monitor. See picture below showing a
generic LAN/WAN connection.
CONNECT ETHERNET CABLE
4
Connect one end of the Power adaptor to the monitor, the other end
to an electrical outlet. This unit powers ON once it is plugged in to the
power outlet.
TIP: Once you are done with the connections, remember to screw the
stand back on.
CONNECT POWER CABLE
5
WAN (WIDE
AREA NETWORK)
LAN (LOCAL AREA NETWORK)
TO YOUR COMPUTER
TO YOUR MONITOR
BACK OF THE ROUTER SHOWN
6
CONTINUED
TIP: Test the cameras prior to selecting
a permanent mounting location by
temporarily connecting the Cameras
and Cables to your System.
* Connect cameras to extension cables
by aligning the arrows. Plug in cameras
and cables before mounting the cameras.
NOTE: The arrow mark on top of the flat side of
the camera and cable connectors should face
UP while inserting to the Monitor.
Connect the first camera to the CH1 input. Follow the same steps to
connect the additional cameras.
4a
You can connect 4 additional (BNC) Cameras using the BNC ports.
With the use of a Universal DIN to BNC Cable you can connect 4 additional 6
PIN DIN Cameras to your monitor.
Note: BNC cameras require separate power adaptors. The SG7610B Camera
Kit includes an individual Power Adaptor and an Universal DIN to BNC Cable.
UNIvERSAL DIN TO BNC CABLE
OPTIONAL
Page: 4
Page: 4Page: 5
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
DATE / TIME SETUP
SETUP
FORMAT
DATE 2007/09/16
TIME 19:08:13
TIME ZONE (GMT-05:00) Eastern Time
DST OFF
DATE YYYY/MM/DD
TIME 24H
INTERVAL OFF
SERVER
TIME SYNC
SYNC
STEP 1 - SET UP YOUR MONITOR FIRST
CONTINUED
The unit will automatically begin loading when power is connected to
the system.
INITIAL LOADING SEQUENCE
c
b
7
a
Click the MENU button on the front panel of the Monitor (or the
Remote Controller) to enter the Main Menu. From the Main Menu
move to SYSTEM and press the ENTER button to go to the DATE/TIME
menu to activate menu options.
SET THE DATE & TIME
9
Congratulations! You have completed Step 1
successfully. You can now view, record and
playback images on your monitor.
Make sure that
the Date and Time
are set prior to
recording.
• MENU Button – Accesses the setup menu, and returns to previous
menu options.
• Navigation Controls - Move Up/Down/Left/Right.
• Enter Button - Press this button to select and change the values in a
menu option.
NOTE: After you see all four (4) camera images
on your monitor screen, remove the protective
film from camera(s) and monitor screen.
a. During the loading sequence, the System will perform a Hard Drive and
Firmware check and the screen will display the text message “SYSTEM
CHECK”.
b. Once the system checks are completed, the screen will display the text
message “INITIALIZING SYSTEM” before completing the loading process.
c. The unit will initially load to a split screen view, displaying all 8 cameras
(if available) and a system legend in a 3x3 Screen View.
MENU NAVIGATION CONTROLS
8
MENU NAVIGATION &
ENTER
NOTE: This may take up to 60
seconds. Please wait until the
system completes loading.
Page: 6
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
Page: 6
STEP 2 - SET UP LOCAL VIEWING ON YOUR PC
*YOUR OBSERVATION SYSTEM MUST BE CONNECTED TO A ROUTER PRIOR TO POWERING IT ON.
RECORD THE IP AND MAC ADDRESSES IN THE SECTION BELOW
NOTE: The system will lease
networking information from
your Router. If you wish to set
your information manually,
then set the DHCP MODE to
MANUAL. Please consult your
Hardware Manual for further
Menu options.
IP ADDRESS: . . .
MAC ADDRESS:
(Required for DDNS registration)
RETRIEVE SYSTEM INFORMATION
To retrieve the System Information, press the ENTER button on the front
panel of the Monitor or the Remote Control.
1
Insert the Lorex Client 3.0 Software CD into your local computer’s CD ROM
drive and proceed with the installation.
INSTALL SOFTWARE
(on your local computer)
Computer - not included
THIS STEP RELATES TO REMOTE VIEWING OVER THE LAN (LOCAL AREA NETWORK) BY USING A
PC LOCATED ON THE SAME NETWORK AS THAT OF THE SYSTEM.
2
Page: 6
Page: 6Page: 7
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
STEP 2 - SET UP LOCAL VIEWING ON YOUR PC
CONTINUED
Follow the installation screens to complete Lorex Client 3.0
Software installation.
LOREX CLIENT 3.0 SOFTWARE
3
RUN LOREX CLIENT 3.0 SOFTWARE
(on your local computer)
4
LorexClient LorexPlayer
Lorex Client and LorexPlayer icons will appear on your desktop.
Double-click the Lorex Client icon on your desktop to run the program.
The log-in window may appear before the main program window loads.
Enter your password to start the program.
NOTE: Initial password is blank
Click the Menu button and select the NEW item.
ADD A LOCAL SITE:
(on your local computer)
5
TIP: When you run LorexClient on Windows XP operating system, you
will see the Windows Security Alert. Please click unblock to run the
application.
Please refer to your Lorex Client 3.0 Software Manual for instructions
about using Lorex Backup Player and Storage Calculator.
Page: 8
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
Page: 8
STEP 2 - SET UP LOCAL VIEWING ON YOUR PC
CONTINUED
Enter a name and site information for the remote site.
1. Enter a Name of the site (e.g. Office)
2. Enter the User ID (admin by default)
3. Enter the User Password (blank by default)
4. Enter the DVR/Monitor TCP/IP port (3000 by default)
5. Enter the IP Address recorded in Step 2-1
6. Click Add to add the remote site
7. Click EXIT
ENTER SETUP INFORMATION
(on your local computer)
6
LOCAL LIVE SCREEN
(on your local computer)
Highlight the site you set-up in Step 2-6. Click the Connect
button and select the Connect item to connect the remote
site.
CONNECTION
(on your local computer)
7
Congratulations! You have completed Step 2 successfully.
You can now view, playback images and remotely control
your system on your local computer over the Local Area
Network (LAN).
8
8
1
2
3
45
67
Ofce
Page: 8
Page: 8Page: 9
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
STEP 3 - SET UP INTERNET REMOTE
MONITORING
PORT FORWARD YOUR ROUTER
1
Port forward your router first before proceeding with the set-up
(ports 80, 3000, 3001, 3002, 3003).
All routers are different. To port forward your router, please refer to
your router’s user manual.
A router configuration guide is available on your Lorex Client Software
CD and also on www.lorexcctv.com/support in the Consumer’s
Guide Section.
DDNS SET-UP
Open your web browser (Internet Explorer by default)
and enter
http://ddns.strategicvista.net
in the address bar.
CREATE ACCOUNT
From the http://ddns.strategicvista.net website, click the
CREATE ACCOUNT option.
3
Router - not included
2
http://ddns.strategicvista.net
Page: 10
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
Page: 10
STEP 3 - SET UP INTERNET REMOTE
MONITORING CONTINUED
COMPLETE NEW ACCOUNT INFORMATION
4
1. FOR PRODUCT LICENSE select the L19LD800 Series option
from the drop down menu.
2. FOR PRODUCT CODE enter the Monitor’s MAC address
(recorded in step 2-1).
3. FOR URL REQUEST enter a unique URL name
(e.g. myurl). NOTE: URL name should not be more than
15 characters.
12
3
REGISTRATION EMAIL
An automated REGISTRATION CONFIRMATION EMAIL will
be sent to your email. Print and Save this confirmation. You
will need this information to access your System remotely.
5
Service Provider: dns1.strategicvista.net
Domain Name: myurl.strategicvista.net
User ID: tomsmith1
Password: (your password)
ENTER DDNS SET-UP ON YOUR MONITOR
Once the DDNS settings have been configured online,
the information must be entered on the System to
allow for remote connection via the Lorex Software (or
through Internet Explorer).
Access the Main Menu Setup screens by pressing the
MENU key on the front panel of your monitor (or Remote
control) and navigate to the NETWORK option and press
ENTER. On the NETWORK SETUP screen scroll down
and select DDNS. Press the ENTER button to access the
DDNS network settings.
6
ENABLE DDNS SETTINGS
On the DDNS SETUP menu, enable DDNS by setting
ON/OFF to ON.
7
Page: 10
Page: 10 Page: 11
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
STEP 3 - SET UP INTERNET REMOTE
MONITORING CONTINUED
VIRTUAL KEYBOARD CONTROL
The Virtual Keyboard control becomes Available
when keyboard input (A~Z, 0~9) is needed for entering
information such as Names, Network Information, etc.
• Navigate using the arrow keys on the Front Panel or by
using the Remote Control or a mouse.
• Use the ENTER key to choose the letters and numbers.
• Select the OK button once the setup is completed.
SET THE DDNS SETTINGS
NOTE: Use arrow keys to move to each item. Press Enter key to
select and change settings.
Enter the DOMAIN NAME sent to you in the REGISTRATION
CONFIRMATION EMAIL (i.e. myurl.strategicvista.net) leaving out
the .strategicvista.net part of the URL.
Enter the USER NAME (e.g. tomsmith1) sent to you in the
REGISTRATION CONFIRMATION EMAIL.
Enter your PASSWORD (blank by default).
Click the CHECK button – DDNS STATUS GOOD message will
appear if the settings are correct.
Press the MENU key to save your settings and exit.
8
9
Insert the Lorex Client 3.0 Software CD into your remote computer’s
CD ROM drive and proceed with the installation.
INSTALL SOFTWARE
(on your remote computer for viewing your system from a remote location)
Computer - not included
10
Page: 12
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
Page: 12
ADD A REMOTE SITE
(on your remote computer)
STEP 3 - SET UP INTERNET REMOTE
MONITORING CONTINUED
Lorex Client and LorexPlayer icons will appear on your desktop.
RUN THE LOREX CLIENT 3.0 SOFTWARE
(on your remote computer)
Double-click the Lorex Client icon on your desktop to run the program.
The log-in window may appear before the main program window loads.
Enter your password to start the program.
NOTE: Initial password is blank
12
LorexClient LorexPlayer
13
Click the Menu button and select the NEW item.
Follow the installation screens to complete Lorex Client 3.0
Software installation.
LOREX CLIENT 3.0 SOFTWARE
(on your remote computer)
11
TIP: When you run LorexClient on Windows XP operating system, you
will see the Windows Security Alert. Please click unblock to run the
application.
Please refer to your Lorex Client 3.0 Software Manual for instructions
about using Lorex Backup Player and Storage Calculator.
Page: 12
Page: 12 Page: 13
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
14
STEP 3 - SET UP INTERNET REMOTE
MONITORING CONTINUED
CONNECTION
(on your remote computer)
Select the site you want to connect to from the Remote Site list,
and then click the Connect button to initiate connection. Once
connected, you will see images from the remote system.
15
Live View
Congratulations! You have completed Step 3 successfully.
You can now view, playback images and remotely control
the system on your Remote computer over the Internet.
Enter a name and site information for the remote site.
1. Enter a Name of the site (e.g. Office)
2. Enter the User ID (admin by default)
3. Enter the User Password (blank by default)
4. Enter the DVR/Monitor TCP/IP port (3000 by default)
5. Enter the DOMAIN NAME sent to you in the
REGISTRATION CONFIRMATION EMAIL
(e.g. myurl.strategicvista.net) leaving out the
.strategicvista.net part of the URL.
6. Click Add to add the remote site
7. Click EXIT
ENTER SETUP INFORMATION
(on your remote computer)
NOTE: The DDNS service supports Dynamic IP addresses for
remote connection. When this feature is configured on the remote
system, you can access it remotely using the domain name instead
of IP address. To use this feature, the system should be registered
on the Lorex DDNS server.
Alternatively, if you have a static IP address you can enter it here.
Please refer to the LOREX CLIENT Manual for network setup and
configuration.
1
2
3
45
67
Ofce
myurl
Page: 14
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
Page: 14
FORMATTING THE NEW HARD DRIVE:
The New Hard Drive MUST be formatted. If a new HARD DRIVE is
detected, the system will prompt you to FORMAT the drive.
HDD INSTALLATION
The System comes with a pre-installed Hard Drive, however
the unit will work with a replacement single Hard Drive (up to
750GB).
NOTE: Make sure that the System is OFF and the power cable has been
disconnected before changing the Hard Drive. For detailed instructions,
check your user’s manual included with the system.
Pre-installed
HDD
SETTING THE NEW DRIVE TO MASTER:
• Refer to the General Jumper Pin Setting on HDD Surface (generally
located on a sticker on the top of the drive).
• Set the Jumper Pin Set to Master (1 Drive). NOTE: Use a Hard Drive
Model with a power supply rated UDMA66 or higher.
CONNECTING THE IDE CABLE:
• Confirm the IDE Cable is securely connected within the System.
RECOMMENDED TIPS
CONNECTING A MOUSE
Connect a mouse to one of the USB ports located on the front
of the unit. The mouse behaves in the same way as a PC mouse
- using Left Click, Right Click and Center Wheel. For detailed
information, please check the System User’s Manual.
NOTE: A three button mouse is required for the full
range of mouse functionality to be available.
LEFT CLICK RIGHT CLICK
CENTER WHEEL
REMOTE CONNECTION USING A MOUSE DRAG &
DROP IN LOREX CLIENT SOFTWARE
Select a previously configured location from the “Remote
Site” window, and simply drag it to the location of live view-
ing (camera display) portion of the screen. All cameras from
the remote system will be displayed. You can also drag spe-
cific cameras to any available square in the Live View area,
as shown in the picture.
The software has an advanced feature which allows you to
connect to multiple sites and view cameras from different
locations simultaneously on one screen (maximum of 16
cameras). Simply drag the specific cameras from each site
you wish to connect to into the live viewing area.
Page: 14
Page: 14 Page: 15
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
RECOMMENDED TIPS CONTINUED
Enter SYSTEM menu on your monitor by pressing the
MENU key on the front panel of your monitor (or Remote
Control). Scroll down to SCREEN SAVE and press ENTER.
MONITOR POWER SAVING TIP
To extend the life of your monitor, it is highly recommended
that you take advantage of the AUTO BRIGHTNESS &
MAIN DISPLAY OFF features. Enabling these features will
save power by automatically dimming your monitor when
not in use or turning the monitor OFF during off-peak hours
(NOTE: recording will not be turned OFF or affected by
these settings). Follow these simple instructions to extend
the life of your monitor.
SYSTEM SET-UP MENU
2
1
On the SCREEN SAVE menu, use arrow
key to move to each item. Press Enter
key to select and change.
1. Enable Screen Saver by setting ON/
OFF item to ON.
2. Select TYPE (TIME or AUTO):
TIME causes the system to turn on the
power of screen once the time is
same as the value in the SCREEN ON
field and turn off the power of screen
once the time is same as the value in
the SCREEN OFF field.
AUTO causes it to turn off the power of screen
once there isn’t any user operation in the sys-
tem for TIME OUT. The TIME OUT options are:
1 MIN, 5 MIN, 10 MIN, 30 MIN, and 1 HOUR.
SCREEN SAVE MENU
3. Enter Time Period:
In case that the TYPE is TIME, enter time in the
SCREEN OFF field to determine the time you
want the Main Display OFF.
NOTE: In case of TIME, you can turn on the
power of screen by pressing the POWER key on
the front panel while the Screen Save mode.
4. Select AUTO TIME OUT
In case that the TYPE is AUTO, select an item
in the TIME OUT field to determine the timeout
you want the Main Display OFF.
NOTE: In case of AUTO, the system turns on the
power of screen by detecting any user opera-
tion while the power saving mode.
5. Press MENU key to save settings and exit
menu.
Page: 16
L19LD800 SERIES QSG_EN_R2
www.lorexcctv.com
It’s all on the Web
For detailed setup information, please refer to your User’s Manual. For additional
information about determining your IP address, configuring your router, and
port forwarding, please visit our website www.lorexcctv.com/support and click
Consumer Guides Section or view guides from the CD included with your system.
Email Support: [email protected]
Toll Free Technical Support - North America: 1-888-42 LOREX (1-888-425-6739)
Toll Free Technical Support - International (outside of North America): 00-800-425-6739-0
Lorex International Website - www.lorexinternational.com
PRODUCT SUPPORT
Specification Sheet
User’s Manual
Lorex Client Software Manual
Quick Start Guide
Port forwarding Guide
Basics of Remote Video
Access Guide
PRODUCT SUPPORT
www.lorexcctv.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Lorex L19LD800 Series Quick start guide

Lorex
Brand
Lorex
Model
L19LD800 Series
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents