For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
MODEL T32250
24" BED EXTENSION
FOR G0844
INSTRUCTIONS
COPYRIGHT © APRIL, 2021 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
(FOR MODELS MFD. SINCE 01/21) #AI21699 PRINTED IN CHINA V1.04.21
Figure 2. Tailstock centered over bed extension
and lathe bed.
Bed
Extension
Lathe
Tailstock
Lathe
Bed
Introduction
The Model T32250 24" Bed Extension increases
the bed length of the Model G0844 benchtop
lathe to accommodate longer workpieces.
A. Bed Extension ............................................ 1
B. Cap Screws M8-1.25 x 25 .......................... 2
C. Lock Washers 8mm.................................... 2
D. Flat Washers 8mm ..................................... 2
E. Rubber Feet ............................................... 2
Inventory (Figure 1)
6mm Hex Wrench .............................................. 1
5mm Hex Wrench .............................................. 1
Tools Needed
Installation
1. Thread rubber feet into bottom of bed extension.
2. Remove (2) button head screws and flat wash-
ers securing accessories tray to tailstock end
of lathe bed.
Figure 1. Model T32250 inventory.
A
B
DE
C
3. Secure bed extension to lathe bed with (2)
M8-1.25 x 25 cap screws, 8mm lock washers,
and 8mm flat washers. Finger-tighten only.
4. Center tailstock over bed extension and lathe
(see Figure 2), and tighten tailstock lock
lever. This will align bed extension and lathe
bed to bottom of tailstock.
5. Fully tighten bed extension cap screws.
6. Loosen tailstock lock lever, and slide tailstock
over length of bed extension and lathe bed.
— If tailstock catches where lathe and bed
extension meet, loosen fasteners and
repeat Steps 4–6 until it slides smoothly.
7. Place straightedge over bed extension and
lathe bed to verify they are parallel and aligned.
-2- T32250 24" Extension Bed (Mfd. Since 1/21)
8. Install acessories tray to bed extension with
(2) button head screws and flat washer
removed in Step 2.
Refer to Model G0844 manual for instructions on
operating lathe.
If you need help with your new bed extension, call
our Tech Support at: (570) 546-9663.
— If bed extension tilts down, use a strip of
masking tape along bottom edge of lathe
bed to shim the bed extension up (see
Figure 3), then adjust bed extension rub-
ber feet to level bed surface.
— If bed extension tilts up, use a strip of mask-
ing tape along top edge of lathe bed to shim
bed extension down (see Figure 4), then
adjust rubber feet to level bed surface.
Figure 3. Shimming bed extension up.
Masking
Tape Bed
Extension
Lathe
Figure 4. Shimming bed extension down.
Bed
Extension
Masking
Tape
Lathe
Figure 5. Shimming bed extension left.
Bed
Extension
Masking
Tape
Lathe
T32250 Parts Breakdown & List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PT32250001 EXTENSION BED 24" 4 PT32250004 CAP SCREW M8-1.25 X 25
2 PT32250002 FLAT WASHER 8MM 5 PT32250005 FOOT M8-1.25 X 18
3 PT32250003 LOCK WASHER 8MM
1
2
3
4
5
— If bed extension is skewed left or right,
use a vertical strip of masking tape along
corresponding edge of lathe bed to make
bed extension parallel with lathe bed (see
Figure 5).
/
