luminii Solo 16 Plus Surface Installation guide

Brand: luminii

Model: Solo 16 Plus Surface

Type: Installation guide

This manual is also suitable for

luminii Solo 16 Plus Surface provides a powerful and versatile lighting solution for various applications. With its 12.6W power consumption and 1245lm output, it delivers bright and efficient illumination. The Solo 16 Plus Surface is designed for surface mounting and offers adjustable pan and tilt angles, allowing for precise light positioning. Additionally, it supports a wide range of accessories, including snoots, microlenses, and optic caps, enabling customization of beam angles and light distribution to meet specific requirements.

instruction manual

Solo 11, 16 & 16 Plus series

Surface Mounted

Constant Current

Solo 11 4.2W 405lm

Solo 16 8.4W 700lm

Solo 16 Plus 12.6W 1245lm

These instructions cover procedures for all

surface mounted versions of Solo 11, 16 & 16

Plus series.

1. All systems must be installed by

a suitably qualied professional

only. Installations must conform to

national installation and accident

prevention regulations.

2. Do not install any xture closer

than 150mm from any combustible

material. Do not install these

products in a damp or wet location.

3. To reduce the risk of re and burns,

do not install these products where

exposed bare conductors can be

shorted or contact any conductive

materials. Do not conceal or extend

exposed conductors through a

building wall.

4. Ensure all connections are tight. Bad

connections can cause overheating,

arcing and a potential re risk.

5. Always use appropriate optics and

ensure they are tted securely.

6. Use only as described in this

Precision Lighting manual.

7. Use only Precision Lighting

recommended accessories.

8. Ensure that the luminaire is switched

off at mains supply before installing

or removing.

9. Luminaires may be extremely hot,

allow to cool before touching.

10. These are LED luminaires, they must

be connected to an appropriate

PSU.

11. Regular cleaning of these products

is important. Switch off at mains

supply and allow to cool before

touching. Clean ttings with a soft

damp cloth and allow to dry before

reconnecting power supply

ABC

Solo 11 & 16

E F

Solo 16 Plus

accessory holder (sold separately)

H I J

KEY PRODUCT FEATURES

A 2 x Screws

B Luminaire Body

C Microlens

D Microlens Cap

E Optic

F Optic Cap

G Snoot

H Accessory (up to 2)

I Accessory Clip

J Double Accessory Holder

03.20

Eldoled 20W 1-10V

Eldoled 30W 1-10V

Eldoled 20W DALI

Eldoled 30W DALI

Eldoled 20W 1-10V

Eldoled 30W 1-10V

Eldoled 20W DALI

Eldoled 30W DALI

COMPATIBLE

POWER SUPPLY

PSCC-20-350-A-EL

PSCC-30-350-A-EL

PSCC-20-350-D-EL

PSCC-30-350-D-EL

PSCC-20-700-A-EL

PSCC-30-700-A-EL

PSCC-20-700-D-EL

PSCC-30-700-D-EL

ORDER CODE

MAX 16 SERIES

LUMINAIRE QTY

MAX 11 SERIES

LUMINAIRE QTY

MAX 16 PLUS SERIES

LUMINAIRE QTY

These instructions are applicable to all

luminaires including:

Solo 11 - Surface

Solo 16 - Surface

Solo 16 Plus - Surface

WARNING

Do not exceed maximum number of

luminaires per driver wattage rating, see

driver datasheet for details.

Remote access required for driver.

WARNING mains supply to driver must

be OFF before connecting or disconnecting

fittings. Do not connect or disconnect

under load.

Ensure driver has not been powered for a

minimum of 1 minute before reconnecting

the LED module after disconnecting.

Do not hot plug. Failure to follow this

WARNING 1-2 luminaires per DRIVER WARNING 1-2 luminaires per DRIVER

instruction will lead to serious damage

of the LED module and driver and will

not be covered by warranty.

NOTE Wire specication: 22 AWG,

ø0.65mm diameter double insulated

teon wire.

Red - Positive Black - Negative

1. Connect Solo luminaires in series to

the driver LED outlet.

Maintain correct polarity when wiring.

Incorrect wiring will cause serious

damage and will not be covered by

warranty. Must be installed according to

SELV regulations.

2. Wire 1-10V or DALI control to LED

driver.

Maintain correct polarity when wiring

dimming control wire. Incorrect wiring

will cause serious damage and will

not be covered by warranty. Must be

installed according to SELV regulations.

1. All systems must be installed by a suitably

qualied professional only. Installations

must conform to national installation

and accident prevention regulations.

2. Ensure that the luminaire is switched off at

mains supply before installing or removing.

3. Do not install these systems in a damp

or wet location, IP20 environments

only. Do not install any xture closer

than 150mm (6 inches) from any

combustible material.

4. To reduce the risk of re and burns, do

not install these systems where exposed

bare conductors can be shorted or

contact any conductive materials. Do not

conceal or extend exposed conductors

through a building wall.

5. Ensure all connections are tight. Bad

connections can cause overheating,

arcing and a potential re risk.

6. Wire supply connections must be made

with U.L or compatible testing agency-

approved connectors. Always use

appropriate optics and ensure they are

tted securely.

7. Install and use only as described in this

Precision Lighting manual.

8. Use Precision Lighting recommended

optics and accessories only.

9. Luminaires may be hot, allow to cool

before touching.

10. Access to serviceable electrical

components should be kept available

for maintenance purposes.

11. Regular cleaning of these products is

important. Switch off at mains supply

and allow to cool before touching.

Clean ttings with a microbre cloth.

Then reconnect the power supply.

instruction manual

Solo 11 / 16 / 16 Plus Surface

Electrical Installation

350mA (11 series) or 700mA

(16 series) Constant Current

Driver.

1 -10V

/ DALI

1 -10V

/ DALI

MAINS MAINS

350mA Constant

Current Driver Output /

Secondary

Output /

Secondary

Solo 11 Surface

Solo 16 & 16 Plus

Surface

700mA Constant

Current Driver

8-10 mm

66 mm

1.5 mm1.5 mm 1.5 mm1.5 mm

16 mm

45 mm 8-10 mm

25.4 mm

Drilling pilot holes and wiring holes

WARNING switch off power to mains

before installation.

WARNING Do not hot plug!

Drill wiring holes for power cable ø

8-10mm.

Drill 2 pilot holes ø1.5mm for screws.

Solo 11 / 16 / 16 Plus Surface

1:1 Drilling Template

A4 Paper size

WARNING

Do not hot plug!

WARNING

Do not hot plug!

Luminaire Solo 11 diameter 45mm / Solo 16 diameter 66mm

Holes for wires diameter 8-10mm

Pilot holes for screws diameter 1.5mm

SOLO 11 SURFACE SOLO 16 / 16 PLUS SURFACE

NOTE Model shown is the Solo 16 LED.

The same procedures apply for Solo 11

LED.

2. 3.

1. Installing the luminaire

Drill the pilot holes and the wiring hole

(See drilling template).

Tilt luminaire 90 degrees to expose holes

for screws. Use a screwdriver to tighten

screws into place.

2. Locking Pan

NOTE Only adjust luminaire position

when unlocked.

Tilt luminaire 90 degrees to expose pan

hole. Adjust luminaire to desired pan

position. To lock into place, insert hex key

provided into pan hole then rotate hex

key clockwise.

3. Removing and changing the snoot

CAUTION the luminaire may be

extremely hot. Allow to cool before

touching.

Unscrew snoot anti-clockwise to remove.

To reattach snoot, align snoot with thread

and screw on clockwise until it stops and

is secure.

4. Changing the microlens

Follow step 3 to remove the snoot.

NOTE Ensure the microlens is inserted

with smooth side / text facing outwards,

and is readable.

Unscrew the microlens cap anti-clockwise

until fully detached. Remove the microlens

and replace with alternative microlens

ensuring it is installed at.

Reattach microlens cap, screw clockwise

until it stops and is tight and secure.

To reattach snoot, align snoot with thread

and screw on clockwise until it stops and

is secure.

4. Changing beam angle

4A)Changing the microlens

NOTE Only applies to Solo 11 & 16 series

Follow step 2 to remove the snoot.

Unscrew the mircolens cap anti-clockwise

until fully detached.

Remove the microlens and replace with

alternative microlens ensuring it is installed

at.

NOTE Ensure the microlens is inserted

with smooth side / text facing outwards,

and text is legible.

Reattach microlens cap, screw clockwise

until it stops and is tight and secure.

Reattach snoot, screw on clockwise until it

stops and is secure.

4B)Changing the optic

NOTE Only applies to Solo 16 Plus series

Follow step 2 to remove the snoot.

Unscrew the Optic cap anti-clockwise until

fully detached.

Gently quarter turn the optic anti-

clockwise and remove.

NOTE Do not touch the exposed LED

Carefully place optic on to LED and gently

quarter turn clockwise to lock it into place.

Reattach Optic Cap, screw on clockwise

until it stops and is secure.

Reattach Snoot, screw on clockwise until it

stops and is secure.

4A).

4B).

5. Installing accessories using the accessory

holder

NOTE Accessory holder ts up to 2

accessories.

Place accessory inside accessory holder

and ensure it is at.

Pinch ends of the retaining clip and insert

into accessory holder to secure accessory

in place.

Insert accessory holder into snoot until it

clicks into place.

6. Changing accessories using the accessory

holder

Accessory holder ts up to 2 accessories.

Remove snoot (step 3) and remove

accessory holder from snoot.

Pinch to remove retaining clip inside

accessory holder to change accessory.

When reassembling, (step 5) ensure

all components are placed at inside

the accessory holder before securing

accessories in place using retaining clip.

Insert accessory holder into snoot until it

clicks into place.

To reattach snoot to luminaire, align snoot

with thread and screw on clockwise until it

stops and is secure.

CLICK

luminii Solo 16 Plus Surface Installation guide

Brand: luminii

Model: Solo 16 Plus Surface

Type: Installation guide

This manual is also suitable for

Download PDF

report

luminii Solo 16 Plus Surface Installation guide

This manual is also suitable for

luminii Solo 16 Plus Surface Installation guide

Related papers

Other documents