Kwikset 66011PRCALRCS Installation guide

Brand: Kwikset

Model: 66011PRCALRCS

Type: Installation guide

This manual is also suitable for

wood block

Installation Guide

www.kwikset.com

*Tools

*Tools will depend on install type

53973 / 01

This manual can be used to install a variety of deadbolts.

1-800-327-5625

Scroll to the bottom if you need help in preparing your door

or or

Latch

1Extend latch bolt (Low prole models)

180°

Use a screwdriver to extend the latch bolt.

Make sure the curve is on

the bottom of the latch.

2Adjust the backset of the latch (if needed)

Use a screwdriver to

retract the latch bolt.

Install

drive-in

collar.

Extend the

latch bolt.

Install backplate.

Install

faceplate.

Make sure the curve is on

the bottom of the latch.

Make sure the curve is on

the bottom of the latch.

Door edge NOT

chiseled

Door edge chiseled or

wood block

3Install Latch

Hold the latch in front of the door hole, with

the latch case ush against the door edge. latch case

If the D-shaped hole is centered

in the door hole, no adjustment is

required. Proceed to step 4.

If the D-shaped hole is NOT centered, adjust

latch. See “Latch Adjustment” (step 3C).

Latch Adjustment

(only if needed)

180°

Rotate the front of the

latch to extend it.

centered

not centered

D-shaped hole

For Low Profile Deadbolts Models

(258 series, Uptown, Downtown, Midtown, and

San Clemente rectangular)

Follow steps 1 through 6

For Regular Deadbolts Models

(158, 159, 660, 665, 780, 816, 980, 985, Halifax and Milan)

Follow steps 7 through 11

Measure the thickness of your door to determine the required mounting screws for step 6.

or or

Actual size Actual size

Call Kwikset to order a service

kit for 2-1/4” (57 mm) thick doors.

Use the screws provided in the kit.

(2x) (2x)

35 mm 44 mm 57 mm

Determine required mounting screws

1-3/8” 1-3/4” 2-1/4”

Install deadbolt interior (Low prole models)

Make sure turnpiece is vertical.

torque blade

latch cam

interior

Mounting plate should be

pre-installed on interior.

If removed, re-install.

Make sure latch bolt is fully extended.

torque blade

turnpiece

exterior

Support deadbolt

interior while

installing exterior.

Use screws from step 4.

Keep parallel.

Curve points up.

Troubleshooting

curve on bottom

Install deadbolt exterior

If the screws are dicult to tighten, make

sure the latch is installed correctly.

To finalize your installation, proceed to Step 12.

Extend latch bolt (Regular deadbolt models)

Adjust the backset of the latch (if needed)

Hold the latch in front of the door hole, with

the latch face ush against the door edge.

If the latch holes are centered in the door hole,

no adjustment is required. Proceed to step 9.

If the D-shaped hole is NOT centered, adjust

latch. See “Latch Adjustment” (step 8C).

Latch Adjustment (only if needed)

not centered

centered

180°Rotate the front of the

latch to extend it.

Prepare latch (if not pre-assembled)

interior

Install deadbolt interior.

(Ring adapter available

with some models) Insert interior

torque blade

into exterior

torque blade.

exterior

Rotate torque

blade to align

with D-shaped

hole.

Install deadbolt exterior. Not available with

all models

Remove interior cylinder.

Pull paper tab to

remove cover plate.

Reinstall cylinder.

Do not reinstall

cover plate.

cover plate

Interior cylinder

has holes.

Remove cover plate from interior cylinder (For double cylinders only).

Door edge NOT

chiseled

Door edge chiseled

Install plate.

Ensure plate snaps into place. Ensure collar snaps into place.

Install collar.

2 tabs

Pull plate to test for tight t.Pull plate to test for tight t.

Door edge NOT

chiseled

Door edge chiseled

wood block

Retract latch bolt.

Extend latch bolt.

Install front plate.

Install

latch.

Install

latch.

“UP” is on top

Install latch (Regular deadbolt models)

11 Install deadbolt (Regular deadbolt models)

The cylinder with holes

should be installed on the

interior side of the door.

Make sure hole in door

frame is drilled a minimum

of 1in (25mm) deep.

Install strike on door frame

Longer screws install

closest to jamb.

1/8 in

3 mm

2-1/8"

54 mm

1/8"

3 mm

25 mm

1/8"

3 mm

2-1/8"

54 mm

1/8 in

3 mm

1/8"

3 mm

2-1/8 in

54 mm

1/8"

3 mm

25 mm

1/8"

3 mm

2-1/8"

54 mm

1/8"

3 mm

1 in

25 mm

Drill holes in door

Select the template that allows you to place

the template on the EXTERIOR side of door.

Fold template along fold line and place fold

line along the edge of door. Place centerline

approximately 38 in (97 cm) from the oor.

Mark hole on the face of the door.

Select desired backset before marking

hole. If there is another hole in the

door, or if you are drilling double

doors, make sure to keep the backset

consistent.

Mark hole on the edge of the

door. Select door thickness before

marking hole.

Drill from one side until the point

of drill just breaks through, then

complete hole from the other side

to prevent splintering.

Exterior

Floor

*Call Kwikset to order a

service kit for 2-1/4 in

(57 mm) thick doors.

35 mm–57 mm*

54 mm

1 in

25 mm

Through door

2 in [51 mm] deep

Preparing Your Door

Use template to mark holes on door

1-3/8 in–2-1/4 in

2-1/8 in

2-3/4 in (70 mm)

2-3/8 in (60mm)

For consumers requiring the door

prep template, please visit:

Drilling instructions

1/8"

3 mm

1/8"

3 mm

1/8"

3 mm

1/8"

3 mm

1/8 in

3 mm

1/8"

3 mm

Latch with drive-in collar

Proceed to Next Step.

Latch with rectangular faceplate

1 in

25 mm

1/8 in

3 mm

3/32"

2 mm

25 mm

1/8"

3 mm

3/32"

2 mm

25 mm

1/8"

3 mm

3/32"

25 mm

1/8"

3 mm

3/32"

2 mm

25 mm

1/8"

3 mm

3/32 in

2 mm

WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock

may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock

can substitute for caution, awareness of your environment, and common sense. Builder’s hardware

is available in multiple performance grades to suit the application. In order to enhance security and

reduce risk, you should consult a qualied locksmith or other security professional.

Rate your product at www.kwikset.com/reviews

Chisel

Mark holes

1 in [25 mm]

deep

Locate center of strike hole:

Measure back from door stop, 1/2 thickness of door.

5/8 in [16mm] deep

DKeep level and trace.

Chisel

Mark holes (2x)

1 in [25mm] deep

Prepare door frame for strike

Determine which latch will be installed and prepare door edge

Kwikset 66011PRCALRCS Installation guide

Brand: Kwikset

Model: 66011PRCALRCS

Type: Installation guide

This manual is also suitable for

Download PDF

report

Kwikset 66011PRCALRCS Installation guide

This manual is also suitable for

Kwikset 66011PRCALRCS Installation guide

Related papers

Other documents