Eonon E1012 User manual

Brand: Eonon

Model: E1012

Category: Car media receivers

Type: User manual

E1012

User Manual

Pleare read this manual before using and

save this manual for future reference.

WELCOME

Thank you for enjoying our series of digital car A/V product.

To properly use this product, please go through this instruction manual for installation

and operation, put it in a safe place for future use!

WARNING

1.Please keep the disk slot clean, wipe it off when there is some dirty on it, please wipe

off the dirty on disk before slot it into the unit. If dirty on disk go into the slot with disk,

that will lead unit to slow slot or cannot read disk. In fact ,that is not quality problem.

Please ask professional to clean the laser. That will bring you some inconvenience.

2.Playing disk for long time or high volume level will influence the lift of unit. To protect

this unit, please work with radio, middle level volume level during long time use.

3.This unit is set up by precision parts. Please do not open the unit or adjust any parts

inside unit by yourself.

4.Please do not touch LCD display by hard object to protect in form scratch.

5.To avoid accident caused by scatterbrain, driver should not operate this unit or watch

its screen. If needed, please park the car in a safe play before operation.

6.This unit is for 12V and negative ground system car, please do not connect it directly in

24V truck or bus.

NOTE: We keep improving this product, if there is any change, forgive us do not

announce.

MODE

Sound,image

12CM

DVD

VCD

MP3

Note: 1. This unit is compatible with MP4/DVD/VCD1.0/2.0/3.0 version,

DVD, CD-R, CD-RW, MP3, WMA, JPEG.

2. When play DVD, VCD, MP3, CD disc, display will auto identify

the disk and show corresponding word. When appear on

display, that means no that function, please choose other function.

Detailed operation please refer to other related instructions.

NOTE

● This unit can play the following disc:

ICON

CONTENT

DISC SIZE

Sound,image

Sound only

●It may lead to accident if you are going to change unit.

●Playing disk during car run on bumpy road will damage laser. Playing substandard disk

or damage disk will damage laser.

●The environment of inside car is not good, too much dirty, please clean the laser by

laser cleanser timely.

●Do not work under terribly hot or cold environment, please ensure the temperature in

car is in -20℃～60℃.

●During operation, if appear on LCD, that means unit do not support that function,

operation is invalid.

●When unit is showing some abnormal, please refer to TROUBLE SHOOTING in this

instruction manual, If you cannot find any solution, please press RESET to resume to

initial status.

FEATURES

DVD PLAYER

1. International advanced MPEG-4 DECODE TECHNOLOGY

2. COMPATIBLE WITH MP4 (AVI/DIVX/5.X), DVD(DVD-R/DVD-RW),

VCD, SVCD, CD-RW, WMA, MP3 JPG

3. Multiple subtitles, angles, languages supporting, Child lock function

4. 4 CHANNEL AUDIO OUTPUT MODE

5. PAUSE, PLAY, UP/DOWN, STOP, ZOOM, PBC FUNCTION

6. FM/AM RADIO TUNER

30 RADIO STATION (18FM, 12AM)

BLUETOOTH FUNCTION

1. Bluetooth wireless transfers

2. Support displaying bluetooth paring and connection status, call status and caller's ID

3. Robust performance, fast connection, accurate and sensible search of devices in range

4. Support A2DP, AVRCP, HS/HF for handing calls and playing music.

LCD DISPLAY

1. 7inch, 16:9 TFT LCD display

2. Touch screen

3. Auto adotoried panel

4. Angle of turn adjustable

SPECIFICATIONS:

Power supply..........................................................................................................DC 12V

Power range...............................................................................................10.8-16.0V DC

Max operate current.....................................................................................................10A

Ground system.........................................................................................Negative ground

FM tuner

Frequency range...........................................................................................87.5-108MHz

Signal/Noisse ratio......................................................................................................55dB

Stereo separation............................................................................................(1KHz)30dB

Search station volt.............................................................................................20-30dBuv

Distortion rate.............................................................................................................1.5%

AM tuner

Frequency range..........................................................................................522-1620KHz

Limit noise sensitivity..................................................................................................32dB

DVD PLAYER

Signal/Noise ratio.......................................................................................................70dB

Frequency response......................................................................................20Hz-20KHz

BASIC OPERATION

1.SOURCE ON/OFF

Press SOURCE button on panel or PWR button on remote control shortly to power on,

Press SOURCE button on panel or PWR button on remote control longer to power off.

2.PLAYING SOURCE CHOOSE

Press SOURCE button on remote control, unit will switch source of playing as

following sequence:

RADIO → DVD → AUX → TV→Bluetooth

1)During switch mode, TFT LCD display will show the name of mode in English;

2)You can't switch to CDC and GPS mode by SOURCE button, content as follows:

RADIO

DVD

AUX

Bluetooth

3.MUTE CONTROL

Press MUTE button on panel or MUTE button on remote control shortly to turn off

sound output, press again to back to sound output.

4.VOLUME ADJUSTMENT

1)Press VOL+/VOL- button on panel, VOL+/VOL- button on remote control or touch

button on display to adjust volume level.

2)The tone of volume is 0-39.

TONE MODE ADJUSTMENT (SEL)

Press SEL button on remote control shortly or touch area or SEL button on panel to

choose your desired tone mode:

VOL→BAL→TRE→L/R

F/R

NOTE:

1)At DVD playing state, MBP & User will be automatically activated.

2)After 5 seconds you choose desired mode, do not adjust volume button, the mode

will auto to back to status before adjustment.

WIRING DIAGRAM

This player is equipped with ISO standard connector, please follow below instruction:

● Red - ACC ON (+12V) ● Grey/Grey black - Right front speaker anode/cathode

● Yellow - Battery anode (+12V) ● White/White black - Left front speaker anode/cathode

● Black - Ground line ● Purple/Purple black - Right rear speaker anode/cathode

● Blue - Power Antenna Control line ● Green/Green black - Left speaker anode/cathode

● Orange - Backsight camera power

control line

● Pink - Braking line

5.RESET

1) If unit is dad abnormal status appear because of wrong operation, press RES

button on panel by penpoint, unit will resume work.

2) After reset, all setting will resume to setting before leaving factory.

PANEL ARRANGEMENT

1.SOURCE BUTTON

2.REL BUTTON

3.MINI USB PORT

4.RESET BUTTON

5.REMOTE CONTROL RECEIVER

6.MUTE/TFT ON/OFF BUTTON

7.VOL- BUTTON

8.VOL+BUTTON

9.OPEN BUTTON

TROUBLE SHOOTING

PROBLEM

CAUSE

SOLUTION

Can not power on

Check whether power fuse

melt or not

Some factor cause MPU wrong

operation

Change fuse same as the old one

Press RESET button on the panel by pen

point, then, power on

After ignition

switch off, setting

information all lose

Wrong connection between

ignition line ACC and power

line anode pole BAIT

Reconnect line

Remote control no

function

No enough power supply

from battery

Change battery of remote control

Poor performance

of radio station

Improper set of length of

antenna, poor connection of

antenna grounding

Check whether antenna is connected or not,

or poor connection

Can not load disc

There is a disc in deck

Check grounding is connected or not

Can not play disc

Disc is scratched

Put wrong side of disc into unit

Lens has dirty

Change new disc

Clean lens by lens clean disc

Slot in the disk with sign side up

Can not switch

language/subtitle

There is only one language/

subtitle in disc

If disk is not with multi-language/subtitle, it

cannot switch language/subtitle

No image

Video line between unit and

TV is not properly connected

Reconnect lines

2.Panel button control instruction

1.SOURCE BUTTON

Press this button for a short moment to turn on power,and long press it to turn off power.

Every button-press activates mode

change as follows:Note:When the

device without connecting to USB.

SD,CDC or DVD no Disc inside,

the system will automatically skip

These related wording mode.

2.Release button

Press this button can take off the control panel.

3.MINI USB PORT

The audio and wiedo documents can be red by mini USB port which is with

standard high speed USB port.

4.RESET BUTTON

Press this button to make the unit back to the mode default.

5.REMOTE CONTROL RECEIVER

It can receive infrared massage of remote control.

6.MUTE/TFT ON/OFF BUTTON

Press this button shortly to turn off volume output,press again to resume former

volume level.

Press this button longer to turn on/off TFT LCD display.

7.VOL- BUTTON

Press this button to reduce the volume.

8.VOL+ BUTTON

Press this button to increase the volume.

RADIO

DVD

AUX

USB

GPS

CDC

(Optional)

OTHER PLAY MODE

AUX IN:

AUX IN OPERATION

1) Press “Source” button on remote control or touch “AUX” on the touch screen, switch

AUX mode.

2) Make video input plug connect to AUX video input outlet, audio input connect to

AUX audio input outlet.

3)This unit only supply 1pcs video input & 1 pair audio input.

CCD (Car backsight function)

1) If there is a car back

camera on your car, please connect car back control line “BACK” to your car camera

control terminal, and connect video input line to the video output terminal of your car

camera.

2) When car is back, the unit will auto switch to CCD mode, and there is a “ ”

appeared on the screen.

3) You can set CCD image according to your car's own position in general setting mode.

9.OPEN BUTTON

In other audio source,press this button to slide up or down display.At that time,load disk,

unit will play it and close the display.If there is a disk inside,unit will auto eject disk.

10.Disk Slot

11.Slot indicator light

12.SD Slot

11 12

Operations and Settings for the Bluetooth Function

1.Features of the Bluetooth function

1)You can use the function buttons on the unit to receive a call or dial a phone number.

2)You can directly use the hand-free microphone to talk on the phone.

3)You can use the build-in volume control switch to adjust the volume at will.

4)You can switch between the Bluetooth hand-free mode and the cell phone mode.

5)You can use your voice to dial a new number (valid only for cell phones with voice

dialing function).

6)With the Bluetooth function, you can use the Bluetooth microphone in the car to talk

with your folks and friends without having to hold your cell phone, so that your hands

are dedicated for driving, which is safer and law-observing. In the mean time, magnetic

radiation from the cell phone is avoided.

2.Bluetooth match conditions

You can shortly touch the Bluetooth function key  under the main menu to directly

access the Blueetooth interface.

With a cell phone that supports the function of Blueetooth wireless connection, you can

establish a connection between your cell phone and the automobile-loaded unit under the

Bluetooth mode to achieve date exchange and synchronization.

3.Matching and connections between the cell phone and the Bluetooth of the unit

Set your cell phone to the Bluetooth mode, and use the cell phone to search equipments.

After the Bluetooth equipment of the unit is searched, the cell phone will ask you for the

Bluetooth password. Press the unit matching setup button , and enter the Bluetooth

password (0000) and confirm it, and then the cell phone will ask you whether you

authorize

the connection with this equipment or not. Please select “YES”, and the cell phone will be

automatically connected with the said Bluetooth equipment within 30 seconds. “OK LINK”

will be displayed on the Bluetooth interface to show that a connection between the cell

phone and the Bluetooth device has been successfully established. Under and mode

(radio, TV, DVD, etc.), if there is an incoming call to your cell phone which has been

stably

connected to the Bluetooth device of the unit, the unit will switch from other mode to the

Bluetooth mode after the cell phone rings for about 10 seconds. Current mode will be

automatically restored after hang-up.

MAIN MENU TOUCH OPERATION

DVD

USB/SD

BLUETOOTH

RADIO

GPS

IPOD

CCD

AUX INPUT

PATTERN SET

Hand-free button: After a phone number is keyed in, press this button to call

the user of this phone number. When there is an incoming call. Press this button

to connect this call.

Hang-up button: When there is an incoming call, press this button to hang up

or refuse to connect it.

Delete button: When a wrong digit is keyed in, press this button to delete the

wrong digit.

Number keys: You can use these number keys to enter a phone number.

Phone number display: The phone number that you have just entered is Displayed

here.

Contact book mode switching

You can touch this button under the Bluetooth mode to select the next mode.

Touch this function key to search the dialed numbers. Each time

This key is touched, the cursor will move to the next dialed number.

Touch this function key to search the received numbers. Each time

This key is touched, the cursor will move to the next received number.

Touch this function key to search the missed numbers. Each time

This key is touched, the cursor will move to the next missed number.

940

1.Bluetooth hand-free/cell phone switching

2.Voice dialing function

3.Contact book mode switching

4.Matching function during Bluetooth connection

5.Hand-free key

6.Hang-up key

7.Delete key

8.Phone number display

9.Number keys

10.Return to the main screen

BLUETOOTH TOUCH OPERATION

Functions and Descriptions

Bluetooth hand-free/cell phone switching

If you touch this switching button at the upper-left corner of the screen under the

Bluetooth hand-free mode, the speaker will beep and the hand-free mode will be

switched to the cell-phone mode.

Voice dialing function

If you touch the “Voice dial” button at the lower-left corner of the screen under the

Bluetooth hand-free mode and the cell-phone mode, you will hear the keying tone, and

you can go ahead with the voice dialing function according to the cell-phone instructions.

Eg, if you wish to call someone, you can pronounce his/her name stored in the cell

phone, then ,the name of the person to be called will be played by the speaker, and the

telephone number of this person will be displayed on the screen and automatically dialed.

To cancel voice dialing

If you wish to disable the voice dialing function in the voice dialing mode, you can press

the “Voice dialing” key again, and this function will be disabled after you hearing the

keying tone.

OSD SETUP

Exit

Minute

Radio frequency setting

Time setting

Note:There are 3 buttons automatically changed according to your setting change in radio

state when you activate or exit RDS,Changes are as following:

PTY LOUD, TA EQ, AF ST.

TIME DISPLAY AND ADJUST

Time display: Touch main menu into adjust mode, press time setup button, the

corresponding function will be display in yellow words.

(1)Press ”+” on hour to add hour, press “-” to reduce hour;

(2)Press ”+” on minute to add minute, press “-” to reduce minute.

NOTE: Touch the correspondence function, will be display in green background.

The unit include two times system: Europe time (24 hour setup), America time (12

hour setup), when show the AM mark it indicate morning time, when appear the PM

mark, it show the time of afternoon.

Remark:This unit is with RDS function, it will automatically adjust the time when you

activate RDS function of have received RDS radio channels. At no received RDS radio

channels or AM state,you should adjust the time.

Hour

Radio frequency setting

According to different area to choose frequency,

pls as blew PIC:

Touch TV mode of the menu or press SOURCE button on remote control to switch to

TV mode, auto scan and store channels.

Press AMS/RPT button on remote control or SCAN touch button on display to auto

scan TV channels. The range of scan if full TV channel. The channels will auto store into

number button in sequence.

1. Switch channel

1) Press SEEK + / SEEK- button on panel or SEEK + / SEEK- on remote control or /

touch button on display, unit will skip to previous or next stored channel.

2) Press number button on remote control, unit will skip to appointed channel, for

example, press 6 button, unit will skip to 6 channel. Press 10+, “_ _” will appear on left

top corner of display, press number button 3,9, unit will skip to 39 channel.

2.Manual tuning TV channel

1) Press and hold SEEK + button on panel, SEEK + button on remote control, or

touch button on display to scan TV channel in increase direction.

2) Press and hold SEEK - button on panel, SEEK - button on remote control, or

touch button on display to scan TV channel in descending direction.

3.TV sound system switch

Press the AUDI button on the touch screen to switch TV sound system. The sequence is

as follows:

PAL I→PAL DK →PAL BG →PAL I

4.Blue screen

The display will be blue when there is no signal.

Touch

here.

If the touching is not just ,yuou can use CALIBRATION to adjust.Touch the middle of the

“+” cursor,adjust it as per the order of the figure.

After adjustment,the interface turn to FM status automatically.

Modus einstellen

Brightness adjust: press this

button to adjust panel brightness

Volume adjust: press VOL -

/ VOL + button to adjust

volume

Saturation adjust; to adjust

multicolor saturation

Exit setup

Contrastness adjust: press

this button to adjust black

and white of panel

Sharp adjust: press this button to

adjust sharp sound high and low

Bass adjust: press this button to

adjust bass volume

Adjust front and

rear speaker

Adjust left and

right speaker

Return previous

EQ mode

Rock POP

Aus Rock

Tonality adjust: to adjust

panel definition

Clangorous effects: press

once off clangorous,

press again to come back

Resume standard video

TV MODE

Channel

choosing

Disc open

/close

Press this function to

adjust angel of LCD

display

Back main

Enter

TV system: Press

PAL I SECAM DK PAL M

NTSC M N PAL I

Function choosing: Please

see picture(3) for detailed

operation

Press this button to

select next channel

Press up and

down to switch

channel

Press this button to

turn back previous

channel

Audio system change:

Press from

PAL I PAL DK

PAL BG

One press down to

receive frequency

One press up to

receive frequency

Auto search and

store channel

Mute

on/off

PROGRAM

PLAY DELETE

PROGRAM

PLAY DELETE

10.CD program play

In CD mode, you can set the sequence of playing by the program function, the operation

is as follow:

When CD is playing, press ST/PROG button, then the display shows:

Input the NO. of the song you want to program by the remote control, program the first

song, input your desired song, for example, the sixth song, and press number button 6

on the remote control. Program the second song, press button move the cursor to

2 . Input your desired song, for example, the ninth song, press number button 9 on

the remote control. Press button to program play.

Back to the normal mode, press the ST/PROG button , then press button,

Note: This function can only be worked by the remote control.

11.MP3 program play

In MP3 mode, you can set the sequence of playing by the program function, the

operation is as follow:

When MP3 is playing, press ST/PROG button, then the display shows:

Then, input desired song by remote control.

For example: Program the first song, input 01, press button move the cursor to the

second lattice, input desired song, for example the third song. Program the second song,

press button, work with button, move the cursor to 2 . Input 01, press button

move the cursor to the second lattice, input desired song, for example, the sixth song

(press 6). Press button to program play.

Back to the normal mode, press the ST/PROG button , then press button,

Note: This function can only be worked by the remote control.

REMOTE CONTROL FUNCTION

1.POWER

Press once to switch on, press again to

switch off.

2.MUTE button

Press once to turn off audio output,

press again to resume volume level.

5.EQ button

Press this button to choose POP, ROCK,

EQ off.

6.SEEK + ( ) / SEEK ( ) button

Press this button to manual turning, speed

or quick back, previous song and next song.

7.VOL + ( → ) / VOL - ( ← )

Press this button to increase or decrease

volume level.

8.SEL button

Press this button to choose sound feature.

9.LOUD button

Press this button to startup LOUD function.

10.BAND/P/N button

In radio mode, press this button to choose

band. In VCD, DVD mode, press this button

to choose AUTO, PAL or NTSC system.

11.LOC / RDM button

In radio mode, press this button to switch

between local and direction. In VCD, CD

mode, press this key to randomly play.

12.STOP button

Press this button to stop playing.

13.PLAY /PAUSE button

Press this button to switch between play

and pause. In stop mode, press this button

to play.

14.ST/ PROG button

In radio mode, press this button to choose

stereo or mono station. In audio mode, it

can help STOP button to programmed play.

3.DSP

Press this button to show the time.

4.SOURCE button

Press this button to choose audio sources.

POWER ON/OFF

MUTE

TIME DISPLAY

SOURCE

SEEK+/SEEK-

VOL+/VOL-

SEL

LOUD

BAND/P/N

LOC/RDM

STOP

PLAY/PAUSE

ST/PROG

0-10+

AMS/RPT

TITLE

AUDIO

SET PLAYING TIME

SUBTITLE

PBC/MENU

UP/DOWN / L / ENTER

SLOW

ANGLE

SET UP

OSD

ZOOM

1336

CD/MP3 BASIC OPERATION

Slot in CD/MP3 disc unit will play it automatically. If disc is in slot, press DVD touch

button on main menu can to play.

CD/MP3

CD disc:

MP3 disc: Directory repeat

2.Speed forward / backward play

Press SEEK + / SEEK - button on remote control, or / touch button on display to

speed forward or backward playing.

Note: Hold above button a bit longer to operate.

3.Previous / next song play

In playing mode, press SEEK + / SEEK - on remote control, or / touch button on

display to choose previous/next song.

4.Pause play

In playing mode, press button on remote control, or touchbutton on display to

pause. Press again to back to normal play.

5.Stop play

In playing mode, 1) Press button on remote control to enter the pause mode, the

position will be stored in unit. At that time, press button on remote control or touch

button on display to resume playing at the stored position.

2) Press button on remote control twice to enter into stop mode, here, press

button on remote control or touch button on display, unit will play from the first song.

6.OSD

In playing mode, short press OSD on remote control to show all information of present

disk.

7. Randomly play

In CD mode, press LOC/RDM button on remote control, to instantly play each song.

Press again to back to the normal play.

8. EQ mode

1) This function can only be worked by remote control.

2) When playing CD/MP3, press the “ZOOM” button on the remote control, you can

choose the sound mode.

9.OPEN

Press OPEN button on panel to eject disc3) When enter this function, press the button

/ / / to move the course to select sound mode which in the system menu, after your

selection position will show red color to indicate the confirmation.

1. Repeatedly play

In mode, press AMS/RPT button on remote control, to startup following, repeat

Single song repeat→ Repeat play off.

Single song repeat→ → Repeat play off.

15.0 - 10 + button

Press this button to choose desired song,

section, preset stations.

* Decimal numbers, for example the 19

song, press 1,9 button;

* Centesimal numbers, for example, the

120 song, press 1,2,0 button.

16.AMS / RPT button

In radio mode, press this button to

browse stored stations. In audio mode,

press this button to play repeatedly.

17.TITLE button

In DVD mode, press this button to play

back to the top menu of disk.

18.AUDIO button

In DVD mode, press this button to switch

language of dialogue. In VCD mode,

press this button to choose left track,

tight track, and stereo.

19.SET playing time

In DVD mode, press this button, you can

define playing time.

20.SUBTITLE button

In DVD mode, press this button to switch

language of subtitle.

21.PBC button

In VCD mode, press this button to display

all song menu, work with number button

to choose songs.

22.UP, DOWN, LEFT, RIGHT, ENTER

button

In DVD mode, press this button to move

cursor up, down, left, right to choose item

in menu. Press enter button to confirm

choice.

23.SLOW button

In audio mode, press this button to slow

backward and slow forward.

24.ANGLE button

In DVD mode, press this button to change

play angle.

25.SETUP button

In audio mode, press this button to choose

different set items.

26.OSD display

Press this button to display the title chapter

and the left time.

27.ZOOM button

In DVD/VCD mode, press this button to

ZOOM in. In CD/MP3/USB/SD mode, press

this button to choose EQ.

28.MENU button

Press button to back to the main menu.

BATTERY CHANGE

When control distance of remote control

become shorter or no function, please

change

battery. Please confirm polarity before

change.

Put battery into controller.

Insert battery holder into controller.

PROGRAM

PLAY DELETE

15. PBC (MENU) play

In VCD mode, press this button then play the PBC and display will show whole menu in

disk, work with number button to choose song. When you are playing either song of the

PBC, and you want to stop to select another song, press the button to turn off.

Note:

1) This function can be worked by the control.

2) PBC is suitable for the SVCD and VCD 2.0 disc.

3) In PBC mode, you can not press number button only to choose song.

16. VCD program playing

In VCD mode, you can set playing sequence of songs by program play function. The

program playing operation steps are as follows:

In VCD mode, press ST/PTOG button, display will show;

Input the songs which you want to programmed by the number buttons on remote

control.

Fr example: Program the first song, input your desires song, for example, the fourth

song, and press number button 4 on the remote control. Program the second song,

press button move the cursor to 2 . Input your desired song, for example, the

eighth song, press number button 8 on the remote control. Press button to program

play.

Back to the normal mode, press the ST/PROG button, then press button.

Note: This function can only be worked by the remote control.

Note: When loading a disc, touch screen function can not be used.

This white bar shows the

rate of process of loading

a disc.

8. OSD

In playing mode, short press OSD on remote control to show all information of present

disc.

9.Number button

In VCD mode, press 0-9 number button to input song. For example, you want to choose

th th

13 song, press 10+ button, and then press 3 button once to play 13 song.

Note: This function can only be worked by the remote control.

11. Randomly play

In VCD mode, press LOC/RDM button on remote control, to instantly play each song.

Press again to back to the normal play.

Note: When VCD disk, if PBC is on, RDM will not work.

Links → Rechts → Stereo →Links

.OPEN

Press OPEN button on panel to eject disc.

10. Repeatedly play

In playing mode, press AMS/RPT button on remote control, to startup following, repeat

function. Single song repeat→ Repeat play off.

Note:

1) When playing VCD disc, if PBC is on, no repeat function.

2) After unit is power off or mode is switched to other playing mode except VCD mode,

if you switch back to VCD mode, repeat playing will be cancelled.

12.Scan play

In playing mode, instantly play each song for 15 seconds to scan your desired song.

1) Press 3/INT touch button on display to scan and play from the first song.

2) When heard you desired song, press those button to cancel scan playing, back to

normal playing.

13.Switch Track

In VCD mode, press AUDIO button on remote control to switch track as following

sequence:

DISC PLAY TOUCH OPERATION

When playing disc,touch any position of the screen, it will display the function menu, touch

the menu and the operation of relative function will display.

Note:When loading a disc,touch screen function can not be used.

1.Click to choose play/pause

2.Click to reduce the volume

3.Click to stop playing

4.Click to choose the speed of quick back

5.Click to choose the speed speeding play

6.Click to leap backwards to play

7.Click to leap upwards to play

8.Click to exit

9.Click to enter the next page to setup the menu

10.Click to increase the volume

11.Audio

12.Click to display title,chapter the time already

played, the time left.

13.At MP3 mode,press this button so you can

move the cursor to left/right/up/down and select

the songs which in the system menu.Then press

“OK” button to enter.

14.Click to enter next page set up menu

15.In DVD mode,touch this button to return the

directory menu.

16.Click this button to switch to different angles

of playing picture in the disc.

17.Repeat play

DVD:Title Repeat→Chapter Repeat Repeat

play off

VCD:Single song repea Full disc repeat

Repeat play off

MP3:Single song repeat Directory repeat

Repeat play off

18.Click on this button to enter title menu

19.Click this button to choose language,

20.Click this button and the screen will display

0-10 button

21.Click this button to ZOO in/ZOON out the

picture.

22.Click to enter the menu of operation for

touching.

23.Click this to choose mode as below:

VOL BASS TRE BAL FAD,after your

desired mode is selected,touch VOL+/VOL- to

adjust the volume.

→

t→ →

→ →

t→ t→ t→ t→

VCD BASIC OPERATION

Slot in VCD disc, unit will play it automatically. If disc is in slot, press DVD touch button

on main menu can to play.

1.Pause play

In playing mode, press button on remote control, or touchbutton on display to

pause. Press again to back to normal play.

2.Stop play

In playing mode, 1) Press button on remote control to enter the pause mode, the

position will be stored in unit. At that time, press button on remote control or touch

button on display to resume playing at the stored position.

2) Press button on remote control twice to enter into stop mode, here, press

button

on remote control or touch button on display, unit will play from the first song.

3.Speed forward / backward play

In playing mode, press SEEK + button on remote control, or touch button on display

to speed play.

When you need quick back, press SEEK - button on remote control, or touch button on

display to quick back play.

Note: Hold above button a bit longer to operate.

4.Previous / next song play

In playing mode, press SEEK + / SEEK - on remote control, or / touch button on

display to choose previous/next song.

5.Switch system

In playing mode, short press the BAND/P/N button on remote control, to select PAL,

AUTO, NTSC TV system.

Note: This function can only be worked by the remote control.

6.Slow play

Press SLOW button on remote control to slow play. The level of slow playing is as follows.

Sequence is :

SLOW 1/2 →SLOW 1/3 →SLOW 1/4 → SLOW1/5

PLAY ← SLOW 1/7 ← SLOW1/6

Note: This function can only be worked by the remote control.

7.Zoom in / Zoom out

Press ZOOM button on remote control to zoom in / zoom out the picture. The levels are as

follows:

ZOOM IN 2 →ZOOM IN 3 →ZOOM IN 4 →ZOOM IN 1/2

ZOOM IN OFF ←ZOOM IN 1/4 ←ZOOM IN 1/3

Note:

1. This function can only be worked by the remote control.

2. Image which is zoomed in can be moved by up/down/left/right cursor to move.

3. Image which is zoomed out cannot be moved.

24.Click to select your desired song or chapter

25.Return to the menu one level.

26.Press this button to adjust angles of the monitor.

Note:

1.When playing VCD,if PBC FUNCTION is on,repeat play is not available.

2.PCB is only suitable for VCD.

3.For VCD disc with play memory,you can use the PBC function

4.Press PBC in the remote control,Play/OFF PBC,press one time to play from the first song;

5.When PBC is on,you can choose speed forwawd or backward,leap forward of backward,

but repeat play is not available.

6.When PBC is on, choose casual play ,scan play or search play,PBC function will close

automatically.

DVD MODE

AUDIO SETTING ON TOUCH SCREEN

Audio selection:

VOL →BAS →TRE →BAL→FAD

When using this function, the

position will have a groove for

nothing.

Loud choosing: this function is

defined open, when it is touched at

the first time, the loud function will

be closed, at the same time, yellow

light disappear.

EQ mode: Touch the button

everytime from

ROCK POP

OFF ROCK

The best listening

position choosing

Bass choosing: when

touched the button will be

yellow, touch this button to

exit, touch it again to

resume..

DIGITAL SETUP

(1.Press or button

(2.Press or / / button, Then

to enter.

DIGITAL SETUP DIGITAL SETUP

OP MODE

DYNAMIC RANGE

DUAL MONO

EXIT SETUP

OP MODE

DYNAMIC RANGE

DUAL MONO

EXIT SETUP

LINE OUT

RF REMOD

DIGITAL SETUP DIGITAL SETUP

OP MODE

DYNAMIC RANGE

DUAL MONO

EXIT SETUP

OP MODE

DYNAMIC RANGE

DUAL MONO

EXIT SETUP

OP MODE

DYNAMIC RANGE

DUAL MONO

EXIT SETUP

OP MODE

DYNAMIC RANGE

DUAL MONO

EXIT SETUP

STEREO

MONO L

MONO R

MIX MONO

VIDEO SETTING ON TOUCH SCREEN

You can choose: Brightness,

contrastness, color, sharpness,

adjust the image effect according

to your favor, at the same time,

there will be blue light for noting.

Video mode: When using this

function, the position will have

a groove for nohing.

Image mode: You can choose the area in

the broken line on the panel, standard,

defined, soft, accord what you meed to

choose, when choosing the function, the

bule backsight will disappear.

VIDEO SETUP

BRICHTNESS

CONTRAST

HUE

SATURATION

SHARPNESS

EXIT SETUP

BRICHTNESS

CONTRAST

HUE

SATURATION

SHARPNESS

EXIT SETUP

VIDEO SETUP

BRICHTNESS

CONTRAST

HUE

SATURATION

SHARPNESS

EXIT SETUP

BRICHTNESS

CONTRAST

HUE

SATURATION

SHARPNESS

EXIT SETUP

Page is loading ...

Eonon E1012 User manual

Brand: Eonon

Model: E1012

Category: Car media receivers

Type: User manual

Download PDF

report

Eonon E1012 User manual

Eonon E1012 User manual

Related papers

Other documents