Magnadyne M99XXFDKIT Installation guide

Magnadyne
Brand
Magnadyne
Model
M99XXFDKIT
Category
Motorcycle Accessories
Type
Installation guide

This manual is also suitable for

Ford DIN Radio Mounting Adapter
Radio and radio components not included.
Installation Manual
7 83855 98783 1
M99XXFDKIT
Installation of M99XXFDKIT
STEP 1
Insert the DIN tools into the two holes on each
side of the radio.
(Installer’s Note: It is recommended the
battery be disconected before starting the
replacement process.)
Tools you’ll need
Wire cutters, strippers, flat blade screw driver,
crimp tool and file.
Installation Kit
*Radio and radio components are not included.
STEP 2
Pull out the entire radio out with all of its con-
nections and harnesses.
STEP 3
Unplug the harness and AV cables from the
back of the radio.
(Installer’s Note: Be careful not to let the cables
fall back inside the dash.)
2
Installation of M99XXFDKIT (cont.)
STEP 5
Place the black mounting adapter into the
dash.
STEP 6
If your black mounting adapter in the dash
bows up due to the tension to the inside tabs.
Follow Steps 6A-6D.
(Installer’s Note: If your black mounting
adapter on the bottom does not bow up, skip
to step 7. )
3
Bow up bracket
Ideal bracket location
STEP 4
Cut and strip the old radio’s power wires
starting with yellow constant hot, then black
chassis ground, then red ignition.
(Installer’s Note: Once the power wires are
finished, the speaker wires can be replaced in
any order. See pages 6-7 for wirring diagram
for original radio removed.)
When you have two of the same color wires
stripped, twist them together tightly.
Insert the twisted wires into one of the pro-
vided crimp end connectors.
(Installer’s Note: Make sure that none of the
wire is exposed below the bottom of the end
connector or you could get a short. Trim if
necessary.)
Use a crimp tool to firmly squeeze the two
wires together.
(Installer’s Note: Pliers can be used if a crimp
tool isn’t available.)
4
Installation of M99XXFDKIT (cont.)
STEP 6B
Installer’s Note: Black sharpie can be used to
mark the area where you’ll be filing the rim of
the car dash.
STEP 6C
Make sure to mark the area to file where the
tabs of the bracket are located.
STEP 7
Insert the new black mounting bracket. Make
sure the mounting tabs snap securely into
place.
STEP 6D
Installer’s Note: Use the file tool to file
down the car dash, where the two clips
will be resting. Only file small amounts at a
time and repeat test fitting the bracket until
desired fit is achieved. Approximately 1/2
the lip thickness will be removed.
STEP 6A
Installer’s Note: It is recommended that you
snap in the top clips and align the bottom ones
to make your adjustment.
STEP 9
Bend the mounting tabs down to hold the
collar firmly in place.
STEP 10
Connect all connections to the radio and
insert the radio into the dash. Be sure radio
locks into position.
STEP 11
Snap radio collar into place.
STEP 8
Prepare the new radio collar by sliding it in
the bracket.
(Installer’s Note: Edges of mouting collar can
be made black by using a black sharpie.)
STEP 8A
Installer’s Note: Black sharpie can be used
to touch-up areas on the black plastic or the
mounting collar if it has been scratched.
5
Installation of M99XXFDKIT (cont.)
Installation of M99XXFDKIT (cont.)
Left
Front Speaker
Left
Rear Speaker
+
-
+
-
Blue Wire: Power Antenna
Yellow Wire: 12 VDC Constant
Black Wire: Ground
Green Wire: Rear Left Speaker (+)
Green/Black Wire: Rear Left Speaker (-)
Right
Rear Speaker
Right
Front Speaker
+
-
+
-
White Wire: Front Left Speaker (+)
Gray/Black Wire: Front Right Speaker (-)
White/Black Wire: Front Left Speaker (-)
Gray Wire: Front Right Speaker (+)
Orange Wire: Dimmer
Red Wire: Switched
Purple/Black Wire: Rear Right Speaker (-)
Purple Wire: Rear Right Speaker (+)
13
12
11
10
9
8
7
6
5
4
3
2
1
15A
Speaker Connection
Reference to Radios:
M9900CDS, M9900DVDS, M1-CD
6
STEP 13
ALL DONE! Enjoy your new radio and
installation bracket.
STEP 12
Your almost done!
(Installer’s Note: After checking all
connections re-connect the vehicle’s battery.)
7
Speaker Connection
Left
Front Speaker
Left
Rear Speaker
+
-
+
-
Blue Wire: Power Antenna
Yellow Wire: 12 VDC Constant
Black Wire: Ground
Green Wire: Rear Left Speaker (+)
Green/Black Wire: Rear Left Speaker (-)
Right
Rear Speaker
Right
Front Speaker
+
-
+
-
White Wire: Front Left Speaker (+)
Gray/Black Wire: Front Right Speaker (-)
White/Black Wire: Front Left Speaker (-)
Gray Wire: Front Right Speaker (+)
Red Wire: Ignition Switched 12 VDC
Purple/Black Wire: Rear Right Speaker (-)
Purple Wire: Rear Right Speaker (+)
1 AMP
Audio Amplifier
See Amplifier Instructions
for Proper Connections
Reference to Radios:
M9900, M9900-1, M9900CD, M9999, M9999-2
© Copyright 2013 Magnadyne Corporation
M99XXFDKIT-INS Rev. A 4-24-13
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Magnadyne M99XXFDKIT Installation guide

Magnadyne
Brand
Magnadyne
Model
M99XXFDKIT
Category
Motorcycle Accessories
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents