Vivanco 10 IN 1 UNIVERSAL LCD REMOTE CONTROL Owner's manual
- Category
- Remote controls
- Type
- Owner's manual
This manual is also suitable for
Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, Fax: +49(0)4102 31444,
E-Mail: [email protected] 1
Universal Controller UR 100 LCD
Clock Setting
Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, Fax: +49(0)4102 31444,
E-Mail: [email protected] 2
(GB) Instructions 2
(D) Bedienungsanleitung 3
(F) Notice d’emploi 5
(E) Instrucciones para el uso 7
(I) Istruzioni per l’uso 9
(NL) Gebruiksaanwijzing 11
(PL) Instrukcja obsługi 13
(CZ) Návod na obsluhu 15
(S) Bruksanvisning 17
(DK) Betjeningsvejledning 19
(P) Manual de instruções 21
(RUS)
22
(GR) 24
(GB) Instructions for Universal
remote control
to control almost all TV sets, satellite
receivers, DVB-Set Top Boxes (STB),
DVD players and recorders, CD players
and other infrared-controllable devices.
1 Important – please read
The Vivanco UR is pre-programmed to
control up to 10 devices, replacing
damaged or lost original remote
controls. It controls the basic functions
of the devices for which it has been set
and is not designed to replace all the
functions of the original remote controls.
In order to be able to control your
devices, you must set the remote control
as described in the section "Code entry".
2 Inserting batteries
Open the battery compartment on the
rear of the UR. Then insert 2 new AAA
alkaline or preloaded long shelf life AAA
rechahrgeable NiMH batteries. Make
sure that the polarity is correct: the "+"
and "-" markings on the batteries and in
the compartment must match. To check
functionality, please look on LCD, if e.g.
a clock time and a device code number
is indicated function is ok.
3 Clock Setting
1. Press SET and PWR button
simultanously and release buttons,
when time indication starts
blinking. See Fig..
2. Key in actual time. After 4
th
digit
the blinking stops and time is set.
4 Code entry
The correct control codes can be set via
direct code entry or automatic code
search.
Direct code entry
Using the enclosed code list, note the
possible codes for the device and the
brand.
To set your TV set, proceed as follows:
1. Using the enclosed code list, find
the codes to control your brand of
television (TV). It is possible that
there are several suitable codes
and you should find out the most
suitable.
2. Switch on a program on your TV.
3. Press the SET button, hold it down
and at the same time press a
device button, e.g. TV*), until the
selected device indication is
displayed and the CODE NO. is
blinking.
4. Then enter one of selected three-
digit codes.
5. When the first and second number
buttons are pressed the blinking
goes on; when the third is
pressed, the selected code is
indicated without blinking..
6. Try out the functions. If everything
is okay, you can set the remote
control as described in steps 1 to
5 for other devices. If it is not
okay, try another code for the
same brand.
The letters on the device buttons
TV1/TV2*), DVD/VCR, DVB1/DVB2*)
SAT1/SAT2*), AUX1/AUX2*) are for
your orientation only. You can set each
type of device under any of the buttons.
If you do not find a suitable code for a
device, look for it using the code search.
*): All device keys can be assigned
twice so that 10 different devices can be
Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, Fax: +49(0)4102 31444,
E-Mail: [email protected] 3
controlled altogether. If you press a key
once according to these instructions you
can enter a device code for the first
assignment or control the first device. If
you press a device key twice within 2
seconds you can set the key for a
second device, or control a second
device via the key.
Code search
To control e.g. a TV:
1. Switch on a program on your TV
(on the TV itself or with the original
remote control).
2. Press the SET button, hold it down
and at the same time press a
device button, e.g. TV*) until the
selected device indication is
displayed and the CODE NO. is
blinking.
3. Then press the SET button again
briefly.
4. Press the PWR button approx.
every 2 seconds.
5. When the TV switches itself off,
briefly press the device button
(TV*)) to store the code found.
6. The blinking stops and the search
is ended.
7. Try out the functions. If everything
is okay, you can set the remote
control as described in steps 1 to
6 for other devices. If it is not
okay, continue searching as
described in 1 to 6.
Automatic code search
To control e.g. a TV:
1. Switch on a program on your TV
(on the TV itself or with the original
remote control).
2. Press the device button with which
you want to control a device, e.g.
TV*).
3. Then press the SET button for
approx. 5 seconds until CODE
NO. starts blinking.
4. Release the SET button and point
the UR at the device to be
controlled. The UR .then begins to
emit a test signal about every 2
seconds.
5. When the TV switches itself off,
briefly press the SET button to
store the code found.
6. The code number changing stops
and the search is ended.
7. Try out the functions. If everything
is okay, you can set the remote
control as described in steps 1 to
6 for other devices. If it is not
okay, continue searching as
described in 1 to 6.
5 Controlling devices
To control a specific device, first press a
device button, e.g. TV*) to control the
TV set and then the required function
buttons.
Volume control
With some devices that have no volume
control, such as video recorders, DVD
players, etc. you can control the volume
of the TV without having to press the TV
button first (Punch Through).
(D) Bedienungsanleitung
Universalfernbedienung
zur Steuerung fast aller Fernsehgeräte,
Satreceiver, DVD Player und Recorder,
DVB-Set Top Boxen (STB), CD Player
und anderer infrarotsteuerbarer Geräte.
1 Wichtig – Bitte lesen
Die Vivanco UR .ist vorprogrammiert für
die Steuerung von bis zu 10 Geräten,
um beschädigte oder verlorene
Originalfernbedienungen zu ersetzen.
Sie steuert die Grundfunktionen der
Geräte für die sie eingestellt wurde und
wurde nicht dafür entwickelt, alle
Funktionen der Originalfernbedienungen
zu ersetzen. Sie müssen die
Fernbedienung wie im Abschnitt
“Kodeeingabe” beschrieben einstellen,
damit sie Ihre Geräte steuern kann.
2 Batterien einsetzen
Öffnen Sie das Batteriefach an der
Unterseite der UR, s. Fig. und setzen
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, Fax: +49(0)4102 31444,
E-Mail: [email protected] 19
apparater. Tryck då på en annan
apparatknapp istället för på TV*).
Om det inte är OK, fortsätt leta
enligt punkt 1 till 6.
5 Apparatstyrning
För att styra en specifik apparat, trycker
du först på en apparatknapp, t.ex. TV för
att styra TV och därefter på de önskade
funktionsknapparna.
Volymstyrning
För vissa apparater utan volymstyrning,
videobandspelare, dvd-spelare osv. kan
du styra volymen för TV-apparaten utan
att först behöva trycka på TV-knappen.
(Punch Through).
(DK) Betjeningsvejledning Universal
fjernbetjening
til betjening af stort set alle TV-
apparater, satellitmodtagere, DVD-
afspillere og optagere, DVB-set top
bokse (STB), CD-afspillere og andre
enheder, der kan betjenes via infrarødt
lys.
1 Vigtigt – læs venligst
Vivanco UR er forprogrammeret til
betjening af op til 10 apparater som
erstatning for originale fjernbetjeninger,
der er beskadiget eller gået tabt. Den
styrer grundfunktionerne på de
apparater, som den er indstillet til, men
er ikke beregnet til at erstatte samtlige
funktioner på de originale
fjernbetjeninger. Før fjernbetjeningen
kan benyttes, skal den indstilles som
beskrevet i afsnittet “Indtastning af
kode”.
2 Isætning af batterier
Batterirummet på bagsiden af UR-
fjernbetjeningen (se fig.) åbnes, og 2
AAA alkaliske batterier eller foropladede
AAA genopladelige NiMH-batterier med
lang hyldetid sættes i. Tjek for korrekt
polaritet: Batteriets og batterirummets
"+" og "–" markeringer skal svare til
hinanden. Hvis alt er korrekt, viser LDC-
displayet et klokkeslæt og et apparat.
3 Indstilling af ur
1. Tryk samtidig på knapperne SET
og PWR, indtil visningen af
klokkeslættet blinker. Se billede.
2. Slip nu begge taster og indtast det
aktuelle klokkeslæt (ttmm). Efter
indtastning af 4. ciffer holder
visningen af klokkeslættet op med
at blinke, og tiden er indstillet.
4 Indtastning af kode
De rigtige styrekoder kan indstilles ved
direkte indtastning af koden eller findes
ved hjælp af den automatiske
kodesøgning.
Direkte indtastning af kode
Find ved hjælp af medfølgende kodeliste
frem til koderne, der passer til
pågældende apparat og mærke.
For at indstille dit TV-apparat er
fremgangsmåden følgende:
1. Find de koder på medfølgende
kodeliste, der er beregnet til dit
TV-mærke. Hvis der står flere
koder til rådighed, find frem til den,
der passer bedst.
2. Tænd for en vilkårlig TV-kanal.
3. Tryk på SET-knappen, hold den
nede, og tryk samtidigt på en af
apparatknapperne, f.eks. TV*),
indtil kodenummeret (CODE NO.)
blinker.
4. Indtast nu en af de trecifrede
koder.
5. Når der trykkes på 1. og 2.
ciffertast, blinker tallene videre;
efter tryk på 3. ciffertast vises den
indstillede kode uden at blinke.
6. Afprøv funktionen. Hvis alt
fungerer efter hensigten, indstil
fjernbetjeningen iht. pkt. 1-5 til
betjening af yderligere enheder.
Hvis ikke alt virker efter hensigten,
prøv med en anden kode til
samme mærke.
Apparatknappernes mærkning
TV1/TV2*), DVD/VCR*), DVB1/DVB2*),
SAT1/SAT2*), AUX1/AUX2*) er
Page is loading ...
Page is loading ...
Page is loading ...
Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, Fax: +49(0)4102 31444,
E-Mail: [email protected] 23
''3 '/& 2)
)+ '/(( “< ”.
2 '( #
9'3( ,'(3)-3 ( )
);)(3 ')( 567 (.. '.)
8( 2 1(*)-(
('(/'&;(.-( ,'( 4'.
AAA. =,+3( &')8: .(
„+“ „-„ ,'( ( ;)-
8. > ( ',(
'8), @A-)' /-(
'(.& '3.
3 ) &
1. 9)'(.()) );.3(
) SET PWR, )(
)*)( .28 )& *.
=.. '.
2. 5( 2 ( ,(
) (( (1(( '(.&
(**..). 5( 4 4'
.2)( '('1(& – *-
)'()-
4 !
5'8)-( '&+1( -
.;) )'8 (.
)('(())2 ,
.(. .*(2 .
)
5 '2(..
.(8( & (,& ( / ):, '-(
:& & 0(2 '3
.'.
6& )'3 ((/' (3(
(+1((:
1. < ';()). (
)3( - '()&
((/'. (TV) 0(3 .'.
</.;), 3 )(8
, 2 . ((
,'8 ),((
:&13.
2. <+*( ) ((/'( ) /
'2'...
3. ?;.( ) SET ,
(';& (B );3,
);.3( )'(.())
) '3, )'.('
TV*), )( )*)( .28
(CODE NO.).
4. C(. (( )3())-3
'(:/)*)-3 .
5. 5' ); ('3 '3
4'-: )
';( .28, (
'(8(3 – ,';(& ,(/
.2)&.
6. 5'('8(, (3( ).
> ( '&(, )'3(
567 ) '()( '2.
'3. ). 1 – 5.
> ) )( ',(,
',3( ( '23
& 3 ;( .'.
?/)& ) '3
TV1/TV2*), DVD/VCR*), DVB1/DVB2*),
SAT1/SAT2*), AUX1/AUX2*) ;
08 & 0(3 '(), -
.;(( /8 +,( '3 )
+,+ ).
> & 2-, '3 -
)( .2 )3 :&1(2 ,
1( (2 .(. .
*): <(. ). '3 .;)
/8 ( 4), . ,'/.,
.;) '&8 ,1(3 ;)
10 '/)-. '3.. >
);8 ) ) '/ 2)
)&1(. ', - .;((
( '3 *((
('3 4) , '()&
('-. '3.. 5( 2,
- );.(( ) '3
;- (*()( 2 (), -
.;(( )'8 ) )
'( '3 ) '()(
'-. '3..
D,- '&8, )'.(',
((/'.:
1. <+*( ) /
((/))-: '2'.. ()
.. ((/'(
4'.())2 567).
2. ?;.( ) ) SET ,
(';& (B );3,
Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, Fax: +49(0)4102 31444,
E-Mail: [email protected] 24
)'(.()) );.3(
) '3, )'.(',
TV*), )( )*)( .28
(CODE NO.).
3. C(. (1B '/ ' );.(
) ) SET.
4. ?;.3( ) ) PWR
'.(') ;-( 2 ()-.
5. A2 ((/' -+*&,
( '3 /- );.(
) ) '3 (TV*)),
*,- :')8 )3())-3
..
6. E2)( )'
'('1(&, /)*().
7. 5'('8(, (3( ).
> ( '&(, )'3(
567 ) '()( '2.
'3. ). 1 – 6.
C(. .( TV*) );.( )
'2+ ) '3. >
) )( ',(, 1(
80( ). 1 – 6.
*(&
D,- *8 /.;)8
'&8, )'.(', ((/'.:
1. <+*( ) /
((/))-: '2'.. ()
.. ((/'(
4'.())2 567).
2. ?;.( ) ) '3,
'3 - :( '&8
. '3., )'.(',
TV*).
3. C(. );.3( (*()( 5
() ) SET, )(
/.2( .
4. 9( ) SET
)'8( UR ) '3.
A;-( 2 ()- UR ,(
-8 (-3 2).
5. A2 ((/' -+*&,
' );.( ) ) SET,
*,- :')8 )3())-3
.
6. =.() '('1(&,
/)*().
7. 5'('8(, (3( ).
> ( '&(, )'3(
567 ) '()( '2.
'3. ). 1 – 6.
C(. );.( .( TV*)
'2+ ) '3. >
) )( ',(, 1(
80( ). 1 – 6.
5 (
D,- '&8 '((())-.
'3., );.( )* )
) '3, )'.(', TV &
'()& ((/'., /(. –
);)-( 4))8)-( ).
+(,
? )('-: '3: ,(/
'()& 2'.8+ /
((.2)4):, DVD ..)
.;) '&8 2'.8+
((/' ,(/ '('(8)2
);& ) TV. (Punch Through).
(GR) -./0123 4567/3
8/9242:5:78/51;< 02=:>63 4567/3
FG HIJ FFKL LJ LMNJ HNJ
HMIONJ, IPQIFRSJ RHSJ,
PRPSJ GJGTGGN RGF GQ
DVD, DVB-Set Top Boxen (STB),
PRPSJ GJGTGGN CD RGF
OMMNJ PRPSJ TIP TFHUTIPJ HIJ
FFKL KUN PTVWNJ.
1 ?/@A=8:>B – CA5A>A9;D@2
.:AEF782
XI HMFFHFI Vivanco JGF
IHGFGRO TIGKKGHFKUJI FG
HIJ FFKL UN RGF 10 PRPSJ,
TI GJHFRGHOHG HNJ GPWJHFRSJ
HMFFHNJ TIP UIPJ GMOF
GW. YMUF HF ZGFRU MFHIP
HNJ PRPSJ FG HF ITI UF
PWKFH RGF J UF FGH FG JG
GJHFRGHGHF LM HF MFHIP HNJ
GPWJHFRSJ HMFFHNJ. [UTF JG
PWKH HI HMFFHFI LTN
TFOQHGF HJ TGOGQI
“YFGN RNFRIV”, TIRFKUJIP JG
RGHGH PJGHL I HMFFKL HNJ
PRPSJ G.
Page is loading ...
Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, Fax: +49(0)4102 31444,
E-Mail: [email protected] 26
N=AO68/7/ >M.:>;D
aFG HIJ HMFFKL T.. KFG
HMLG:
1. YTFMU]H UJGJ HGWKL HJ
HMLG G (KUN H
PRP HIP GPWJHFRIV
HMFFHIP).
2. [FUH HI TMRHI SET, RGHH
HI TFKUJI RGF TFUH HGPHLIJG
UJG TMRHI PRP T.. TV*),
KUF I RNFRL GFWKL (CODE
NO.) JG GJGZIZJF.
3. bHJ PJUFG TFUH HI TMRHI
SET FG KG GRLKG QIO.
4. [FU^H HI TMRHI PWR TTIP
GJO 2 PHLMTHG.
5. YOJ HMLG G
GTJITIFW, TFUH VJHIKG
HI TMRHI PRP (TV*)),
TIRFKUJIP JG GTIWRVH HIJ
RNFRL HJ KJK.
6. d UJF] HGKGHO JG
GJGZIZJF RGF GJG^H
HKGH^HGF.
7. YMU]H HJ MFHIPG. \J JGF
JHO]F PWKH HI
HMFFHFI VKQNJG K HG
ZKGHG 1. UN 6. FG HIJ UMI
HNJ PTLMIFTNJ PRPSJ. \JH
FG HI TMRHI TV*) TFUH ROTIFI
OMMI TMRHI PRP. YOJ J
JGF JHO]F, PJH HJ
GJG^H VKQNJG K HG ZKGHG
1 UN 6.
N<8B@A8/ A=AO68/7/ >M.:>;D
aFG HIJ HMFFKL T.. KFG
HMLG:
1. YTFMU]H UJGJ HGWKL HJ
HMLG G (KUN H
PRP HIP GPWJHFRIV
HMFFHIP).
2. [FUH UJG TMRHI PRP,
KUN HIP ITIIP TFWPKH JG
MUH HJ PRP, T.. TV*).
3. _HO TFUH FG TTIP 5
PHLMTHG HI TMRHI SET
KUF I RNFRL GFWKL JG
GJGZIZJF.
4. \QH HI TMRHI SET MVWI
RGF TIGJGHIMH HI
HMFFHFI HJ TI HJ
PRP TIP WUMH JG MUH
K GPHL. XI HMFFHFI
RTUKTF UJG IRFKGHFRL KG
GJO 2 PHLMTHG.
5. YOJ HMLG G
GTJITIFW, TFUH VJHIKG
HI TMRHI SET, TIRFKUJIP JG
GTIWRVH HIJ RNFRL HJ
KJK.
6. d JGMMG HNJ RNFRSJ GFWKSJ
HGKGHO RGF GJG^H
HKGH^HGF.
7. YMU]H HJ MFHIPG. \J JGF
JHO]F PWKH HI
HMFFHFI VKQNJG K HG
ZKGHG 1. UN 6. FG HIJ UMI
HNJ PTLMIFTNJ PRPSJ. \JH
FG HI TMRHI TV*) TFUH ROTIFI
OMMI TMRHI PRP. YOJ J
JGF JHO]F, PJH HJ
GJG^H VKQNJG K HG ZKGHG
1 UN 6.
5 P9204;3 7<7>2<J=
aFG HIJ HMFFKL KG FFR
PRP, TFUH GFRO UJG TMRHI
PRP, T.. TV FG HIJ HMFFKL
H HMLG RGF KHO TFMU]H HG
TMRHG MFHIPFSJ TIP TFWPKH.
P9204;3 I=8A7/3 64;<
b IFKUJ PRPU N
PJGHLHHG TFMI VWKF H
UJHG, LTN T.. PRPU GQ
ZJHI, DVD RMT., KTIH JG
PWKH HJ UJHG H HMLG
N JG TFUH TIIPKUJN HI
TMRHI TV (Punch Through).
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
Vivanco 10 IN 1 UNIVERSAL LCD REMOTE CONTROL Owner's manual
- Category
- Remote controls
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- italiano: Vivanco 10 IN 1 UNIVERSAL LCD REMOTE CONTROL Manuale del proprietario
- français: Vivanco 10 IN 1 UNIVERSAL LCD REMOTE CONTROL Le manuel du propriétaire
- español: Vivanco 10 IN 1 UNIVERSAL LCD REMOTE CONTROL El manual del propietario
- Deutsch: Vivanco 10 IN 1 UNIVERSAL LCD REMOTE CONTROL Bedienungsanleitung
- Nederlands: Vivanco 10 IN 1 UNIVERSAL LCD REMOTE CONTROL de handleiding
- português: Vivanco 10 IN 1 UNIVERSAL LCD REMOTE CONTROL Manual do proprietário
- dansk: Vivanco 10 IN 1 UNIVERSAL LCD REMOTE CONTROL Brugervejledning
- polski: Vivanco 10 IN 1 UNIVERSAL LCD REMOTE CONTROL Instrukcja obsługi
- čeština: Vivanco 10 IN 1 UNIVERSAL LCD REMOTE CONTROL Návod k obsluze
- svenska: Vivanco 10 IN 1 UNIVERSAL LCD REMOTE CONTROL Bruksanvisning
Related papers
-
Vivanco UR Owner's manual
-
-
-
-
-
-
-
-
-
Other documents
-
BAZOO METALBOARD Owner's manual
-
Sony RM-V8A Operating instructions
-
One For All MF-350 User manual
-
Binatone CI-580 User manual
-
One For All MF-350 User manual
-
Schwaiger UFB 801 Instructions Manual
-
-
Lexibook UNIVERSAL TOUCHSCREEN REMOTE User manual
-
TNB RCDL01 Owner's manual
-
Babyfon BM 50 P User manual
