Eaton Nema pushbuttons 10250T contact block Owner's manual

Eaton
Brand
Eaton
Model
Nema pushbuttons 10250T contact block
Type
Owner's manual
Effective June 2011
Instructional Lea et IL04707001E
10250T contact block assembly
• Underwriters Laboratories Listed
• For use on a flat surface of Type 1, 2, 3, 3R,
3S , 4, 4X, 12, and 13 enclosures
• IP65
For indicating lights without moveable operations.
General
1. Drill mounting hole for vertical or horizontal
mounting per one of the figures above.
2. Ensure sealing gasket is in place on the
operator. Align locating nib of operator
with notch in panel and insert operator
through mounting hole. Exception: See
special instruction publication 20437 for
placement of sealing gasket when using
10250T/91000T protective boots.
3. Place legend plate and mounting nut over
operator. Tighten mounting nut. If applicable,
assemble lenses, mushroom buttons, etc., to
operator. Tighten securely (5 ft-lbs) (6.8 Nm).
4. Torque terminals to 7 in-lbs (0.8 Nm).
For ease of assembly, Eaton recommends
the following tools:
• 10250T/91000TA95 for 10250T/91000T octagonal
nuts, E29, and E30 lines
• E22CW for 10250T/91000T octagonal nuts,
E22, E34, and E30 lines
Retaining
Nut
Thrust Washer
(Optional)
Nameplate
Operator
Gasket
Panel
0.063–0.250
(1.6–6.3 mm)
Assemble Master Test or
Flasher Modules to Rear
of Contact Blocks.
Wires Shown are not Included
Ratings are Stamped
on Light Unit
and Contact Block
#755 Lamp
Saddle Clamp Type Terminals
14 AWG–22 AWG
(2.5 mm2—0.34 mm2)
Solid or Stranded.
Do Not Mix One or Two
Conductors per Terminal
Earth/Ground
Conductor
91000/E34
Earth Terminal
ILL
P.B.
IND
LIGHT
PUSH
PULL
T-Line Operator
Lens Washer
0.60
(15.2 mm)
1.20
(30.5 mm)
0.136 (3.5 mm) Diameter Hole or
0.180 (4.6 mm) Rectangular Notch
Use 60/75ºC Copper Conductors Only
Vertical Mounting Horizontal Mounting
Eaton Corporation
Electrical Sector
1111 Superior Ave.
Cleveland, OH 44114
United States
877-ETN-CARE (877-386-2273)
Eaton.com
© 2011 Eaton Corporation
All Rights Reserved
Printed in USA
Publication No. IL04707001E / Z11206
June 2011
Eaton is a registered trademark
of Eaton Corporation.
All other trademarks are property
of their respective owners.
Instructional Lea et IL04707001E
Effective June 2011
10250T contact block assembly
Push–pull operators
Application guide
To assist in the selection of contact blocks, the diagram on page 1
shows pictorially by symbols “A” and “B” locations of contact
circuits after assembly of contact blocks to the operator. Table 1 and
Table 2 show the effect of the push and pull operations on either
NO or NC contacts.
A maximum of two contact blocks may be used with each operator.
Maximum torque of stacking screws is 9 in-lbs. Adding more
than two blocks may cause this switch to malfunction. Single
circuit contact must be mounted under circuit “A”. Special function
contact blocks are not available for use with the three-position
push–pull operator.
ote: N Buttons and lenses in various colors are ordered and packaged sepa-
rately. This pushbutton unit is oiltight when the adapter gasket and button or
lens gasket are securely tightened.
Table 1. Push–Pull Operator Types
Operator
Type
Contact
Block
Circuit
Operator Mode and Contact Circuit
Pulled Intermediate Pushed
Circuits
A B Circuits
A B Circuits
A B
Momentary
push and pull
and
momentary pull,
maintained push
2NC
1NO
X X
O
O X
O
O O
X
Maintained
push and pull
(Two-positions)
1NC
2NC
1NO
2NO
X or X
X X
O or O
O O
No
intermediate
position
O or O
O O
O O
X X
Momentary
push and pull
(Three-positions)
1NO–1NC O X O O X O
ote: N X = contacts closed; O = contacts open
Table 2. Push–Pull Wire Position Operation
Control Line Diagram Operator Circuits Operator Mode
Three-wire,
three-position,
momentary
Circuit
Circuit
L2L1
M
M
OL
A
B
Momentary
push and pull
2NC
contact
blocks
START
(Momentary)
Normal position
(Maintained)
STOP
(Momentary)
Two-wire,
two-position,
maintained
Circuit
L2L1
M
or
OL
AB
Maintained
push and pull
1NC
contact
blocks
START
(Maintained)
No
intermediate
position
STOP
(Maintained)
Three-wire
momentary pull,
maintained push
Circuit
Circuit
L2L1
M
M
OL
A
B
Maintained
push and
maintained
ready,
momentary
pull to start
2NC
contact
blocks
START
(Momentary)
Normal position
(Maintained)
STOP
(Momentary)
  • Page 1 1
  • Page 2 2

Eaton Nema pushbuttons 10250T contact block Owner's manual

Eaton
Brand
Eaton
Model
Nema pushbuttons 10250T contact block
Type
Owner's manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents