NFS Supra / Vision Plus2 / ESS 2Plus
HLSI-MA-025_01 V02_XP
www.honeywelllifesafety.es
NFS Supra / Vision Plus2 / ESS 2Plus
Quick Guide. See the user manual for more information.
Latest manual versions in www.honeywelllifesafety.es
Function Key button Options Function Key button Options
Factory set up Keep Access push button pressed while you are pressing the following sequence key (Z1, Z2 , Z2, Z1) Re use of special functions may contravene the standards. Please check the applicable standards before proceeding
Primary Delay Delay Yes/Not Reset Key
Resetable Faults Keypad Access LED ON => Latched faults. Faults need to be RESET (by default)
OFF=> Resettable faults. Faults RESET automatically when fault has disappeared
Silence delay Mute Buzzer Reset Key
Power supply
supervision Keypad Silence/
Resound LED ON => mains power supply monitored (by default)
OFF=> mains power supply not monitored
Sounder activation
by zone
(Control Matrix)
Silence/Resound Reset Key Zone Key button: Activation mode for every zone
Battery Supervision Keypad Delay On/Off
LED ON => Battery faults are indicated (by default)
OFF=> Battery faults are not monitored
Zone Key button Zone Key (Shortcircuit) Key Reset Button (Zone Type)
Sounder resound Keypad Mute Buzzer
LED ON => A new alarm re-sound the sounders (by default)
OFF => A new alarm does not re-sound the sounders
Digital input Access Key button Reset Key
Remote
communication
monitoring
Keypad Zone 3 Fault led Zone 3 ON = Remote communication monitored
Fault led Zone 3 OFF = Remote communication signal is NOT monitored
Disablement LED
with delays
Access Key button +
Delay On/OFF Reset Key
Battery Ri
monitoring Key Aux.Power supply fault Led ON = High batery Ri value
Aux.Power supply fault Led OFF = Low batery Ri value (standard value for 7Ah batteries)
Cancel delays with
2 zones in alarm Access Key button +
MUTE Buzzer Key
button.
Reset Key
Number of VSN-
4REL boards Keypad Zone 1 Led Z1 = Z2 = Z3 OFF = No VSN-4REL borads installed
Led Z1 ON = one VSN-4REL boards installed
Led Z1 + Z2 ON = two VSN-4REL boards installed
Led Z1 + Z2 +Z3 ON =three VSN-4REL boards installed
Earth fault level Evacuate push button Reset Key
Input monitoring
(Resistive
EOL/Capacitive
EOL)
Access Key button +
Evacuate push button Reset key
Quick guide – Set up options
1
2
3
4
5
6
7
8
9
10
1 min
2 min
3 min
4 min
5 min
6 min
7 min
8 min
9 min
10 min
Set up Access: Place the PROG jumper. (Buzzer every 10 seg + System Fault LED blinking)
Select a function: Press the relevant push buttons (Button led or Key lit)
Change functions: Press Reset button untill the LED of the required option is on..
l
Remove the PROG jumper to save the configuration.
Special set up
Special set up Access: With the panel switched off, place the PROG jumper and switch on the panel
Select the option: Press the required options
(The keypad led shows the chosen option according to ON/OFF LED status )
Remove the PROG jumper to save the configuration.
Detectors (Eco1000 or 470) delayed / Call points ( 5V Zener) not delayed
Detectors (Eco1000 o 470) delayed /Call points (5V Zener) delayed
Detectors (Eco1000 o 470) not delayed / Call points (Zener 5V) not delayed
The zone will not activate the sounder.
1
2 Sounder SND 1
Sounder SND 2
1
2
3
4
Normal
Delayed contact 470 require 30 sec, contact retention.5V Zener not retained
Detector alarm verification (1st alarm is reset, Ack into 10 min.
Delayed contact 470
resistor and 5v Zener require 30sec contact retention
S.C. = Fault
S.C. = Alarm
1
2
3
4
5
Reset
Evacuation
Sound.& Buzz mute
Delay on/off
Buzzer mute
1
2 Disablement led activated with delay (EN54)
Disablement led not activated with delay (Non EN54)
1
2 RFL Zone 6K8 and RFL Sounders 6K8
EOL zones 47µF y EOL Sounders Diode
1
2 Two Zones in alarm DO NOT cancel delays
Two Zones in alarm cancel delays
1
2 Low Sensitivity level
Medium Sensitivity level
3 High Sensitivity level
1
2
3
4
5
6
7
8
9
10
1 min
2 min
3 min
4 min
5 min
6 min
7 min
8 min
9 min
10 min
