2. Flowmaster
  3. 817674

Flowmaster 817674 Installation guide

  • Hello! I'm a chat assistant that has analyzed the provided document, which is an Installation Instructions for the FLOWMASTER system #817674, which is an exhaust system for 2007-2014 Jeep Wrangler JK 2 & 4 door models with 3.6L/3.8L engine. The document outlines the step-by-step process for removing your old system and installing the new one, noting some specific steps for 2 door models. I'm here to assist and answer any questions you might have about the installation or the product.
  • What vehicle models is this exhaust system designed for?
    What material is the exhaust system made of?
    Do I need to make any modifications for a 2-door model?
    Is welding required for installation?
409S® Stainless Steel
11/19/13
Removal:
1) Raise the vehicle up on a hoist or rack to working height. If you do not have access to a hoist or rack,
raise the vehicle and support securely with jack stands.
2) Loosen the band clamp on the inlet side of the muffler (left side).
3) Support the muffler with a stand, and separate the two hanger rods from the rubber mounts. Remove
the muffler assembly. After removing the muffler assembly, remove the nuts securing the factory rear muffler
heat shield. Removing this shield will allow the exit pipe to tuck up tighter to the vehicle.
4) Loosen the band clamp at the rear of the factory Y-pipe and separate the two hangers on the pipe from
the rubber mounts on the vehicle. Lower the pipe from the vehicle and set aside.
Installation:
1) Place a provided clamp onto the slip-fit of inlet pipe assembly #710TBS and
slide over the back of the factory Y-pipe. Connect the hanger on the pipe to the
rubber mount on the vehicle and tighten the clamp enough to hold, but still allow for
adjustment. The hanger closest to the slip-fit is for 07-11 models, the other hanger
is for the 2012-2013 model. You may choose to trim off the hanger that is not used.
2) Place a provided clamp onto the inlet of muffler #12518409-Z and slide over
the back of inlet pipe #710TBS. Tighten the clamp enough to hold, but still allow
for adjustment.
For 2 Door Model Vehicles: you will need to trim 20.50” from the front (long end) of
over-axle pipe #86126S. Additionally, replace the original rubber hanger that is just
forward of the rear axle with new hanger HA484.
3) Place a provided clamp onto the outlet of the muffler and then position the
over-axle pipe assembly #86126S over the rear axle and slide into the muffler
outlet. Connect the hanger on the pipe to the rubber mount on the vehicle and
tighten the clamp enough to hold, but still allow for adjustment.
Pg 1 of 3 Technical Support (707) 544-4761
Installation Instructions for:
SYSTEM #817674
2007-2014 JEEP WRANGLER JK
2 & 4 DOOR MODELS · 3.6L / 3.8L ENGINE
4) Place a provided clamp onto the slip-fit of exit pipe #86127S and slide onto
the back of over-axle pipe #86126S. Connect the hanger on the pipe to the rubber
mount on the vehicle and tighten the clamp enough to hold, but still allow for
adjustment.
5) Adjust the position of the muffler, pipes and exit pipe to provide a satisfactory fit. Maintain a minimum of
3/4" clearance between the Flowmaster system, the drivetrain and chassis components, while also keeping
suspension travel and vibration in mind. Tighten down all clamped connections securely. For a cleaner
appearance and more secure installation, we highly recommend welding all slip-fit connections. Install the
provided push-on hanger keepers onto the ends of all of the hanger rods to prevent them from slipping out of
the rubber hanger mount.
PACKING LIST
Qty Description Part#
1 Inlet Pipe Assembly 710TBS
1 Muffler 12518409-Z
1 Over-axle Pipe 86126S
1 Exit Pipe Assembly 86127S
1 Parts kit PK739
4 2 ½” Clamp MC250BS
4 1/2” Hanger Keeper HW503
1 Rubber Hanger (2-door) HA484
Pg 2 of 3 Technical Support (707) 544-4761
Installation diagram for:
SYSTEM #817674
2007-2014 JEEP WRANGLER JK
2 & 4 DOOR MODELS · 3.6L / 3.8L ENGINE
Technical Support (707) 544-4761
409S® Stainless Steel
/