Hayward Power-Flo Matrix Series Owner's manual

Category
Above ground pool accessories
Type
Owner's manual

This manual is also suitable for

ISSP1591
Rev. D
_________________________________________________________________________________
OWNER’S MANUAL
INSTALLATION, OPERATION, & PARTS
Power-Flo Matrix
Pump Series
The Hayward Power-Flo
®
Matrix™ Pump Series is specifically engineered for the demanding requirements of today’s above-
ground swimming pools. The advanced design reduces maintenance requirements while providing superior performance.
To prevent potential injury and to avoid unnecessary service calls, read this manual carefully and completely.
CAUTION We highly recommend a qualified professional install and service this product.
WARNING This manual contains important safety information that must be furnished to the end
user of this product. FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS COULD RESULT
IN SERIOUS INJURY.
*Only units equipped with 3'
twist-lock cords are UL-listed.
SAVE THIS INSTRUCTION MANUAL
HAYWARD POOL PRODUCTS, INC.
Corporate Headquarters: U.S.A:
620 Division Street 1 Hayward Industrial Drive 2935 Sidco Drive 2875 Pomona Blvd.
Elizabeth, NJ 07207 Clemmons, NC 27012 Nashville, TN 37204 Pomona, CA 91768
Canada: Europe:
2880 Plymouth Drive P.I. Plaine de l'ain
Oakville, Ontario L6H 5R4 Allêe des chênes
01150 St Vulbas France
Power-Flo Matrix
Pump Series ____________________
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety precautions should always be
followed, including the following: Failure to follow instructions may result in injury.
READ AND FOLLOW ALL INSTRUCTIONS
IN THIS OWNER’S MANUAL AND ON
EQUIPMENT.
KEEP SAFETY LABELS IN GOOD CONDITION AND
REPLACE IF MISSING OR DAMAGED.
WARNINGTo reduce risk of injury, do not permit children to use or climb on this
product. The ANSI/NSPI 4 Standard (above-ground and on-ground pools) advises that
components such as the filtration system, pumps, and heaters be positioned to prevent their being
used as a means of access to the pool by young children. Closely supervise children at all times.
CAUTIONThe Power-Flo Matrix™ Pump Series is intended for use on permanently
installed above-ground swimming pools and may also be used with hot tubs and spas if so
marked. Do NOT use with storable pools. A permanently installed pool is constructed in or on
the ground or in a building such that it cannot be readily disassembled for storage. A storable
pool is constructed so that it is capable of being readily disassembled for storage and reassembled
to its original integrity.
Though this product is designed for outdoor use, it is strongly advised to protect the electrical
components from the weather. Select a well-drained area, one that will not flood when it rains. It
requires free circulation of air for cooling. Do not install in a damp or non-ventilated location.
Bond motor to pool structure. Use a solid copper conductor, size or larger. Run wire from
external bonding lug to reinforcing rod or mesh. Connect a No. 8 AWG (8.4 mm²) solid copper
bonding wire to the pressure wire connector provided on the motor housing and to all metal parts
of swimming pool, spa, or hot tub, and to all electrical equipment, metal piping or conduit within
5 ft. (1.5 m) of inside walls of swimming pool, spa, or hot tub. (In Canada use No. 6 AWG
bonding wire.)
PRODUCT REGISTRATION
(
Retain For Your Records
)
DATE OF INSTALLATION ____________________
INITIAL PRESSURE GAUGE READING (CLEAN FILTER) _______________________
PUMP MODEL ________________ HORSEPOWER _______________________
FILTER MODEL ________________ SERIAL NUMBER _______________________
Power-Flo Matrix
Pump Series __________ ________________________
NOTE: The National Electrical Code (NEC) permits use of a cord with a maximum 3 ft.
(1 m) length. If your pump is equipped with a cord complying with the NEC, the following three
(3) items apply.
WARNING Risk of Electric Shock. Connect only to a grounding
type receptacle protected by a Ground Fault Circuit Interrupter (GFCI). Contact a
qualified electrician if you cannot verify that the receptacle is protected by a
GFCI.
WARNING To reduce the risk of electric shock replace damaged cord
immediately. Do NOT bury cord. Locate cord to minimize abuse from lawn
mowers, hedge trimmers and other equipment.
WARNINGTo reduce the risk of electric shock, do NOT use an extension cord to
connect unit to electric supply. Provide a properly located outlet. Qualified personnel MUST do
all electrical wiring.
CAUTIONAll suction and discharge valves MUST be OPEN when
starting the filter system. Failure to do so could result in severe personal injury
and/or property damage. All drains and suction covers MUST have properly
installed covers securely attached with the screws supplied with the covers. If
screws are lost, order replacement parts from your supplier.
DANGERSuction Entrapment Hazard. Never use the pool or
spa if a drain cover is damaged, cracked, missing, or not securely attached. Suction in drains and
suction outlets can cause drowning, disembowelment, hair or body entrapment, severe injury, and
death. Disembowelment, entrapment, or drowning is possible when body parts or hair come in
contact with damaged, broken, cracked, missing, or unsecured drain covers and suction outlets.
Suction from pumps with only one drain or suction outlet can cause disembowelment,
entrapment, or drowning. Pumps for pools and spas require two (2) functioning suction outlets at
least three (3) feet apart, on two (2) walls or on the floor and one (1) wall of the pool or spa.
Installation of pump and suction outlets must be in compliance with all applicable local building
codes. Replace damaged, broken, cracked, missing, or unsecured drain covers and suction outlets
immediately.
WARNINGHazardous Pressure. Pumps, filters, and other
equipment/components of a swimming pool filtration system operate under pressure. Incorrectly
installed and/or improperly tested filtration equipment and/or components may fail resulting in
injury and/or property damage. A qualified pool professional MUST conduct all pressure tests.
This product is intended for above-ground/on-ground swimming pool applications only. Do NOT
connect to a high-pressure system such as a municipal water main. To prevent explosion caused
by entrapped air in the filtration system use provided air relief valve to bleed air from the system.
Confirm that ALL filtration system component clamps, bolts, and covers have been tightened to
the manufacturer’s recommendations.
WARNINGNever operate or test the filtration system at more than 30 PSI.
SAVE THESE INSTRUCTIONS
Power-Flo Matrix
Pump Series ____________________
Product Specifications
Dimensions
General Information
Introduction
This manual contains information for the proper installation and operation of the Hayward Power-Flo Matrix™ pump.
The instructions in this manual MUST be followed precisely.
Product Features
The Above-ground industry’s largest above-ground strainer basket for large debris collection with minimal
maintenance.
Horizontal/Vertical Discharge Feature – Simply converts from horizontal to vertical discharge orientation
with the press of a button.
Quick connect intake and discharge pipe connection.
‘C’ clip connector allows for easy disengagement of strainer housing in a matter of seconds for hassle-free
maintenance.
Heavy duty, high performance motor with integrated automatic thermal overload protector for years of
operation.
High quality Noryl
®
impeller with wide openings to prevent clogging by leaves and large debris.
Durable, corrosion-proof housing for years of dependable service and all-weather performance.
Heat resistant, double-sized seal for long, lasting efficiency.
Energy-efficient, protected rear-mounted switch.
Integral drain plug for easy winterization of pump
Installation Instructions
Pump Location
For best pump performance, locate the system below the
pool water line.
Power-Flo Matrix
Pump Series ____________________
Installation Instructions (cont.)
Pump Location (cont.)
Install pump on a firm, level base or pad to meet all local and national codes. The field supplied base or pad must be
level and vibration-free.
Though the pump is designed for outdoor use, it is strongly advised to protect the electrical components from the
weather. Select a well-drained area, one that will not flood when it rains. Pump motors require free circulation of air
for cooling. Do not install pump in a damp or non-ventilated location.
Pump Mounting
Fasten pump to base or pad with screws or bolts to further reduce vibration and stress on pipe or hose joints.
NOTE: Allow adequate access for servicing pump and piping.
Plumbing
To facilitate servicing of pump and to allow for indoor storage during the winter months, installing union connections
at the suction and outlet ports is recommended.
Use Teflon tape to seal threaded connections on molded plastic components. All plastic fittings must be new or
thoroughly cleaned before use. NOTE: Do NOT use Plumber’s Pipe Dope as it may cause cracking of the plastic
components.
When applying Teflon tape to plastic threads, wrap the entire threaded portion of the male fitting with one to two
layers of tape. Wind the tape clockwise as you face the open end of the fitting, beginning at the end of the fitting.
The pump suction and outlet ports have molded-in thread stops. Do NOT attempt to force hose connector fitting past
this stop. It is only necessary to tighten fittings enough to prevent leakage. Tighten fitting by hand and then use a tool
to engage fitting an additional 1 ½ turns. Use care when using Teflon tape as friction is reduced considerably; do
NOT over-tighten fitting or you may cause damage. If leaks occur, remove connector, clean off old Teflon tape, re-
wrap with one to two additional layers of Teflon tape, and re-install connector.
Electrical
WARNING – Ground motor before connecting to electrical power supply.
Failure to ground pump motor can cause serious or fatal electrical shock hazard.
WARNING – Do NOT ground to a gas supply line.
WARNING – To avoid dangerous or fatal electrical shock, turn OFF power to
motor before working on electrical connections.
WARNING – Ground Fault Circuit Interrupter (GFCI) tripping indicates
electrical problem. If GFCI trips and won’t reset, consult electrician to inspect and repair electrical
system.
WARNINGFire Hazard. Match supply voltage to motor nameplate voltage.
Insure that the electrical supply available agrees with the motor’s voltage, phase, and cycle, and that the wire size is
adequate for the H.P. (KW) rating and distance from the power source.
NOTE: All electrical wiring MUST be performed by a qualified professional, and MUST conform to local
codes and regulations.
Power-Flo Matrix
Pump Series ____________________
Installation Instructions (cont.)
Electrical (cont.)
Voltage
Voltage at motor MUST NOT be more than 10% above or below motor name plate rated voltage, or motor
may overheat, causing overload tripping and reduced component life. If voltage is less than 90% or more
than 110% of rated voltage when motor is running at full load, consult power company.
Grounding/Bonding
Install, ground, bond, and wire motor according to local or national electrical code requirements.
Permanently ground motor. Use green ground terminal provided under motor canopy or access place; use
size and type wire required by code. Connect motor ground terminal to electrical service ground.
Bond motor to pool structure. Use a solid copper conductor, size or larger. Run wire from external bonding
lug to reinforcing rod or mesh. Connect a No. 8 AWG (8.4 mm
2
) solid copper bonding wire to the pressure
wire connector provided on the motor housing and to all metal parts of swimming pool, spa, or hot
tub, and to all electrical equipment, metal piping or conduit within 5 ft. (1.5 m) of inside walls of swimming
pool, spa, or hot tub.
Wiring
If other lights or appliances are also on the same circuit, be sure to add their amp loads before figuring wire
and circuit breaker sizes. (NOTE: If unsure how to do this or if this is confusing, consult a licensed
electrician). Use the load circuit breaker as the Master On-Off switch.
Install a Ground Fault Circuit Interrupter (GFCI) in circuit; it will sense a short-circuit to ground and
disconnect power before it becomes dangerous to pool users. For size of GFCI required and test procedures
for GFCI, see manufacturer’s instructions.
In case of a power outage, check GFCI for tripping, which will prevent normal pump operation. Reset if
necessary.
NOTE: If you do not use conduit when wiring motor, be sure to seal wire opening on end of
motor to prevent dirt, bugs, etc., from entering.
New Installation – Start-Up & Operation
Prior to Start-Up
Fill strainer housing with water to suction pipe level. NEVER operate the pump without water. Water acts as a
coolant and lubricant for the mechanical shaft seal.
WARNING NEVER run pump dry. Running pump dry may damage seals, causing leakage
and flooding. Fill strainer housing with water before starting motor.
CAUTION – Do NOT add chemicals to pool/spa system directly in front of pump suction.
Adding undiluted chemicals may damage pump and voids warranty.
CAUTION – Before removing strainer cover:
1. STOP
PUMP before proceeding.
2. CLOSE VALVES in suction and outlet pipes.
3. RELEASE ALL PRESSURE from pump and piping system.
Power-Flo Matrix
Pump Series ____________________
New Installation – Start-Up & Operation (cont.)
Prior to Start-Up (cont.)
WARNING If pump is being pressure tested, be sure pressure has been
released before removing strainer cover.
WARNING Do NOT block pump suction. To do so with body may cause fatal
injury. Small children using pool MUST always have close adult supervision.
Selecting Pump’s Discharge Position (4 Steps)
Your Hayward Power-Flo Matrix™ pump can be easily positioned for horizontal or vertical water discharge.
Step 1: Remove ALL plumbing attached to pump. Remove pump
from base (if applicable).
Step 2: Remove strainer housing.
Disengage and lift off strainer cover.
Remove strainer basket.
Lift up on strainer ‘C’ clip and remove.
(See Fig. 1)
Slide strainer housing forward and remove.
Step 3: Press positioning button located on pump housing and
rotate discharge port to desired position.
(NOTE: Discharge port will only rotate ¼ turn.) Figure 1
Step 4: Assemble the pump by following the above directions in the reverse manner.
Priming Pump
Open all valves before starting system.
Release all air from filter and piping system. See filter owner’s manual.
When water source is higher than the pump, pump will prime itself when suction and outlet valves are
opened.
Clean and lubricate strainer cover O-ring with "Jack's 327" each time it is removed.
Clean and inspect O-ring; re-install on strainer cover.
Replace strainer cover on strainer housing; turn clockwise to tighten cover.
NOTE: Tighten strainer cover by hand only (no wrenches) ¼ turn.
If pump does NOT prime within ten minutes, stop motor and determine cause. Be sure all suction and discharge
valves are open when pump is running. See Troubleshooting Guide.
Storage/Winterization
WARNING Explosion Hazard. Purging the system with compressed air can cause
components to explode, with risk of severe injury or death to anyone nearby. Use only a low
pressure (below 5 PSI), high volume blower when air purging the pump, filter, or piping.
CAUTION Allowing the pump to freeze will void the warranty.
CAUTION Do NOT use anti-freeze solutions (except propylene glycol) in your pool/spa
system. Propylene glycol is non-toxic and will not damage plastic system components; other anti-
freezes are highly toxic and may damage plastic components in the system.
Power-Flo Matrix
Pump Series ____________________
Storage/Winterization (cont.)
Drain all water from pump and piping when expecting freezing temperatures or when storing pump for a long time
(see instructions below).
Gravity drain system as far as possible.
Keep motor dry and covered during storage. To avoid condensation/corrosion problems, do NOT cover or wrap pump
with plastic film or bags.
Storing Pump For Winterization
WARNING To avoid dangerous or fatal electrical shock hazard, turn OFF power to motor
before draining pump.
1. Drain water level below all inlets to the pool.
2. Remove drain plug from bottom of strainer body.
3. Disconnect pump from base.
4. Once the pump is removed of water, re-install the strainer lid and strainer plug.
5. Store pump in a dry enclosure.
Start-Up For Winterized Equipment
1. Securely mount pump to base.
2. Install all intake and output fittings and piping.
3. Refill pool to proper water level.
4. Prime pump according to instructions.
Shaft Seal Change Instructions
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ AND FOLLOW ALL INSTRUCTIONS
When servicing electrical equipment, basic safety precautions should always be observed including the following. Failure to
follow instructions may result in injury.
A.
WARNING To reduce risk of injury, do not permit children to use this product.
B. Disconnect all electrical power service to pump before beginning shaft seal replacement.
C. Only qualified personnel should attempt rotary seal replacement. Contact your local authorized Hayward
Dealer or service center if you have any questions.
D. The National Electrical Code requires either a three (3) foot maximum twist-lock cord set with a GFCI
protected receptacle or hard wire (conduit) connection for swimming pool pump installation. Do not use
extension cords.
SAVE THESE INSTRUCTIONS
Exercise extreme care in handling both the rotating and the stationary sections of the two-part replacement seal. Foreign matter
or improper handling will easily scratch the graphite and ceramic sealing surfaces.
1. Shut off water flow to pump by closing appropriate valves or by plugging both the skimmer outlet port and return port
to pool. Disconnect piping or hoses from the motor/pump assembly.
2. Remove the strainer by disengaging and removing the strainer cover. Remove the basket. Lift up on strainer ‘C’ clip
and remove. Finally, slide strainer housing forward and remove.
3. Unscrew eight (8) screws and remove pump cover, exposing the impeller.
4. Remove the canopy or the shaft cover plate from the end of motor opposite the impeller.
Power-Flo Matrix
Pump Series ____________________
Shaft Seal Change Instructions (cont.)
5. Hold the motor shaft securely by either inserting a screwdriver in slot at end of shaft or by using an open-end wrench
to engage the flat surfaces provided near end of motor shaft. Rotate the impeller ina a counterclockwise direction and
remove it from the motor shaft.
6. Note how the steel spring section of the old seal is positioned on impeller hub and remove it by pulling from the
impeller.
7. Loosen four (4) motor through bolts from the back of motor and remove pump housing/shroud from the front of the
motor.
8. Remove the ceramic stationary portion of the old seal by pressing the white ceramic seat out of the pump housing
recess. If assembly is tight, tap lightly from the “motor” side.
9. Clean and lubricate the impeller stem and the pump housing recess with a dilute solution of non-granulated liquid-type
soap. Do not use petroleum or silicone lubricants as these can contribute to seal leakage.
10. Press the new rotating portion of the seal assembly onto the impeller stem with the polished black graphite surface
facing away from the impeller.
11. Carefully press the stationary ceramic portion of the seal into the recess of the pump housing/shroud, with the polished
flat surface facing out.
12. Carefully insert the motor shaft through the pump housing/shroud and align with white ceramic stationary seal
assembly in place and secure the motor to pump housing/shroud with four (4) motor through bolts removed in step #7.
Be sure motor base and pump discharge port are positioned properly. Alternately tighten the motor through bolts until
the pump housing is secure. Make certain motor shaft turns freely before proceeding.
13. Screw the impeller (clockwise) with the rotating portion of seal in place onto the motor shaft. Hand-tighten the
impeller in place.
14. Clean (replace if necessary) the O-ring and replace on pump cover. Assemble the pump cover to the pump housing/
shroud with the eight (8) screws removed in step #3. Tighten screws alternately and evenly.
15. Re-assemble strainer by sliding strainer housing onto pump cover. Install strainer ‘C’ clip by pushing clip down onto
grooved pump cover coupling. Insert basket and fasten strainer cover.
16. Reconnect pump to the piping or hoses provided. Open all valves and make sure that the pump strainer housing is full
of water before restarting the pump.
Troubleshooting
Motor Will NOT Start – Check For:
1. Improper or loose wiring connections; open switches or relays; tripped circuit breakers, GFCI’s, or blown fuses.
2. Manually check rotation of motor shaft for free movement and lack of obstruction. (See steps 4 & 5 of “Shaft
Seal Change Instructions” in this manual.)
3. If you have a timer, be certain it is working properly. Bypass it if necessary.
Motor Shuts OFF – Check For:
1. Undersized wiring; loose connections; etc.
2. Low voltage at motor or power drop (frequently caused by undersized wiring or extension cord use).
3. Mechanical binding and electrical overload.
NOTE: Your Hayward pump motor is equipped with an “automatic thermal overload protector.” The motor will
automatically shut off if power supply drops before heat damage can build up causing windings to burn out. The
“thermal overload protector” will allow the motor to automatically restart once the motor has cooled, provided the
power source is again up to proper levels. It will continue to cut On/Off until the problem is corrected. Be sure to
correct cause of overheating.
Motor Hums, But Does NOT Start – Check For:
1. Centrifugal switch stuck in OPEN position.
2. Binding of motor shaft.
Power-Flo Matrix
Pump Series ____________________
Troubleshooting (cont.)
Pump Won’t Prime
1. Make sure pump/strainer housing is filled with water and the cover O-ring is clean, also be sure it is properly
seated in the cover O-ring groove. Make sure strainer cover is locked firmly in position and lubricated with
“Jack’s 327.”
2. Make sure all suction and discharge valves are fully open and not blocked, that pool water level is at proper level,
and that skimmer weir is not hung up or binded on skimmer wall.
3. Block off to determine if pump will develop a vacuum. You should have 5”-6” of vacuum at the strainer cover
(Only your pool dealer can confirm this with a vacuum gauge). You may be able to check by removing the
skimmer basket and holding your hand over the bottom port with skimmer full and pump running. If no suction
is felt, check for line blockage.
a. If pump develops a vacuum, check for blocked suction line or dirty strainer basket, an air leak in the
suction piping may be the cause.
b. If pump does not develop a vacuum and pump has sufficient “priming water”:
i. Re-check strainer housing cover and all threaded connections for suction leaks. Check if all
hose clamps are tight.
ii. Check voltage to ensure that the motor is rotating at full RPM’s.
iii. Open housing cover and check for clogging or obstruction in suction. Check impeller for
debris.
iv. Remove and replace shaft seal only if it is leaking.
Low Flow – Generally, Check For:
1. Clogged or restricted strainer or suction line; undersized pool piping.
2. Plugged or restricted discharge line of filter, valve partially closed (high gauge reading).
How to correct:
Sand filters – backwash as per manufacturer’s instructions; D.E. filters – backwash as per
manufacturer’s instructions; Cartridge filters – clean or replace cartridge.
3. Air leak in suction (bubbles issuing from return fittings). Re-tighten using Teflon tape.
4. Plugged or restricted impeller or impeller sheared off. Replace including new seal assembly.
Noisy Pump – Check For:
1. Air leak in suction piping causing rumbling in pump.
2. Cavitation due to restricted or undersized suction line or leak at any joint, low water level in pool, and
unrestricted discharge return lines. Correct suction condition or throttle return lines, if practical. Holding hand
over return fitting will sometimes prove this point or putting in a smaller eyeball fitting.
3. Vibration due to improper mounting, etc. Put a rubber pad under metal mounting feet.
4. Foreign matter in pump housing. Loose stones/debris hitting impeller could be cause, remove any of the above.
5. Motor bearings noisy from normal wear, rust, overheating, or concentration of chemicals causing seal damage
which will allow chlorinated water to seep into bearings wiping out the grease causing bearing to whine. All seal
leaks should be replaced at once.
6. Equipment base vibrating.
Maintenance
Clean strainer basket regularly. Do NOT strike basket to clean. Inspect strainer cover gasket regularly and
replace as necessary.
Hayward pumps have self-lubricating motor bearings and shaft seals. No lubrication is necessary.
Keep motor clean. Insure air vents are free from obstruction.
Occasionally, shaft seals must be replaced, due to wear or damage. See “Shaft Seal Change Instructions” in this
manual.
Power-Flo Matrix
Pump Series ___________________
Replacement Parts
Parts Diagram
Parts Listing
Ref. No. Part No. Description Ctn. Qty. No. Req’d
1 SPX5500D Strainer Cover with Lock Ring & 'O' Ring 10 1
2 SPX5500H Strainer Cover 'O' Ring 10 1
3 SPX5500F Strainer Basket 10 1
4 SPX5500G Strainer Retainer/ 'C' Clip 10 1
5 SPX5500C Strainer Housing 1 1
6 SPX1700FG Drain Plug w/ Gasket 10 1
7 SPX5500K Strainer 'O' Ring 10 1
8 SPX0714Z48 Screw, #14 x 1/4" Type B Pan Head 80 8
9 SPX5500B Pump Cover 4 1
10 SPX0710XZ5 Housing 'O' Ring 10 1
11 ---- Impeller (Refer to Part No. on Original Equipment) * 1
12 SPX1500KA Shaft Seal Assembly 10 1
13 SPX5500A Pump Housing 4 1
14 SPX5500E Shroud Assembly 4 1
15a SPX1510Z1E ¾ HP Motor with Switch, Flex-48 1 1
15b SPX1510Z1XE 1 HP Motor with Switch, Flex 48 1 1
15c SPX1515Z1E 1 ½ HP Motor with Switch, Flex-48 1 1
15d SPX1520Z1ESC 2 HP Motor with Switch, Flex-48 1 1
15e SPX1524Z1ESC 2 ½ HP Motor with Switch, Flex-48 1 1
16 (optional) SP1500UNPAK2 Union Connector Assembly 50 2
Power-Flo Matrix
Pump Series
__________
Retain this Warranty Certificate (upper portion) in a safe and convenient location for your records.
DETACH HERE: Fill out bottom portion completely and mail within 10 days of purchase/installation.
------------------------------------------------------------------------------------------------------------
Mail to: Hayward Pool Products, Inc., 620 Division Street, Elizabeth, NJ 07207, Attn: Warranty Dept.
Warranty Registration Card
Name__________________________________________________ Years pool has been in service less than 1 1-3 3-5 5-10
Address________________________________________________ Purchased from:
Company name________________________________________________
City______________________State_________ Zip ____________
Address_______________________________________________________
E-mail Address:_________________________________________
City___________________________State____________Zip_____________
Product Purchased_______________________________________
Product Serial No.________________________________________
Please send me more information on these other
New Installation Replacement products from Hayward:
Type of Pool:
Pump Filter Automatic Pool Cleaner
In-ground Vinyl Fiberglass Gunite Above-ground Light Chlorinator Skimmer
Heater
Size of Pool______________________________________
HAYWARD
®
LIMITED WARRANTY
This pump was inspected before shipment from our plant. To original purchasers of this pump, Hayward Pool
Products, Inc., 620 Division Street, Elizabeth, New Jersey, warrants its products free from defects in materials and
workmanship for a period of ONE (1) year from the date of purchase.
Parts which fail or become defective during the warranty period, except as a result of freezing, negligence, improper
installation, use, or care, shall be repaired or replaced, at our option, without charge, within 90 days of the receipt of
defective product, barring unforeseen delays.
To obtain warranty replacements or repair, defective components or parts should be returned, transportation paid, to
the place of purchase, or to the nearest authorized Hayward service center. For further Hayward dealer or service
center information, contact Hayward customer service department. No returns may be made directly to the factory
without the express written authorization of Hayward Pool Products, Inc.
To original purchasers of this pump, Hayward Pool Products, Inc. warrants its pump housing/strainer to be free from
defects in materials and workmanship for a period of ONE (1) year from the date of purchase.
Pump housing/strainers which become defective during the warranty period, except as a result of freezing,
negligence, improper installation, use or care, or as the result of a use in association with an automatic valving
system, shall be repaired, at our option, without charge.
All other conditions and terms of the standard warranty apply.
Hayward shall not be responsible for cartage, removal and/or reinstallation labor or any other such costs incurred in
obtaining warranty replacements.
The Hayward Pool Products warranty does not apply to components manufactured by others. For such products, the
warranty established by the respective manufacturer will apply.
Some states do not allow a limitation on how long an implied warranty lasts, or the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
Hayward Pool Products, Inc.
620 Division Street
*Supersedes all previous publications. Elizabeth, NJ 07207
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Hayward Power-Flo Matrix Series Owner's manual

Category
Above ground pool accessories
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI