Milwaukee SDS PLUS 5263-59A User manual

TM

MANUAL DE INSTRUCCIONES

MANUAL DO OPERADOR

OPERATOR’S MANUAL

Cat. No.

5263-59

5263-59A

5263-59B

ROTOMARTILLO SDS PLUS DE 20 mm

MARTELETE ROTATIVO ROMPEDOR DE 20 mm SDS-PLUS

3/4" SDS PLUS ROTARY HAMMER

Page is loading ...

TECHNICAL DATA

Rated input ................................................................................

Output ........................................................................................

Voltage.......................................................................................

No-load speed ...........................................................................

Speed under load max. .............................................................

Rate of percussion under load max. ..........................................

Impact energy per stroke according to EPTA-Procedure 05/2009 ......

Drilling capacity in concrete .......................................................

Drilling capacity in steel .............................................................

Drilling capacity in wood ............................................................

Optimized capacity in concrete/brick .........................................

Chuck neck diameter .................................................................

Weight according EPTA-Procedure 01/2003 .............................

Noise Information

Measured values determined according to EN 60745.

Typically, the A-weighted noise levels of the tool are:

Sound pressure level (K = 3 dB(A)) .........................................

Sound power level (K = 3 dB(A)) .............................................

Wear ear protectors!

Vibration Information

Total vibration values (vector sum in the three axes)

determined according to EN 60745.

Vibration emission value a

h

:

Hammer-drilling in concrete: ..................................................

Uncertainty K = ......................................................................

GENERAL POWER TOOL SAFETY WARNINGS

WARNING! Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric

shock, re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

power tool.

1) Work area safety

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres, such

as in the presence of ammable liquids, gases or dust.

Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodied plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces,

such as pipes, radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is earthed

or grounded.

c) Do not expose power tools to rain or wet conditions. Water

entering a power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable,

use a residual current device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

tool while you are tired or under the inuence of drugs,

alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in

the off position before connecting to power source and/

or battery pack, picking up or carrying the tool. Carrying

power tools with your nger on the switch or energising power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating

part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewellery or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

WARNING

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given

in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.

The declared vibration emission level represents the main applications of the tool. However if the tool is used for different

applications, with different accessories or poorly maintained, the vibration emission may differ. This may signicantly increase

the exposure level over the total working period.

An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or

when it is running but not actually doing the job. This may signicantly reduce the exposure level over the total working

period.

Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the

accessories, keep the hands warm, organisation of work patterns.

5263-59 / 5263-59A 5263-59B

..................... 620 W ........................... 620 W

..................... 310 W ........................... 310 W

220-240 V~ 50-60Hz ............127V~ 50-60Hz

............0-3700 min

-1 ...............................

0-3700 min

-1

............0-2700 min

-1

..................0-2700 min

-1

............0-4400 min

-1

..................0-4400 min

-1

........................2,0 J ..............................2,0 J

.....................20 mm ...........................20 mm

.....................13 mm ...........................13 mm

.....................30 mm ...........................30 mm

..................5-12 mm ........................5-12 mm

.....................43 mm ...........................43 mm

......................1,9 kg ............................1,9 kg

.................90 dB (A) .......................90 dB (A)

...............101 dB (A) .....................101 dB (A)

....................12 m/s

2

..........................12 m/s

2

...................1,5 m/s

2

.........................1,5 m/s

2

21

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for

your application. The correct power tool will do the job better

and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tool or these

instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other condition

that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind

and are easier to control.

g) Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed. Use

of the power tool for operations different from those intended

could result in a hazardous situation.

5) Battery tool use and care

a) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of battery

pack may create a risk of re when used with another battery

pack.

b) Use power tools only with specically designated battery

packs. Use of any other battery packs may create a risk of

injury and re.

c) When battery pack is not in use, keep it away from other

metal objects, like paper clips, coins, keys, nails, screws

or other small metal objects, that can make a connection

from one terminal to another. Shorting the battery terminals

together may cause burns or a re.

d) Under abusive conditions, liquid may be ejected from the

battery; avoid contact. If contact accidentally occurs, ush

with water. If liquid contacts eyes, additionally seek medical

help. Liquid ejected from the battery may cause irritation or burns.

6) Service

a) Have your power tool serviced by a qualied repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS

Wear ear protectors when impact drilling. Exposure to

noise can cause hearing loss.

Use auxiliary handles supplied with the tool. Loss of

control can cause personal injury.

Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accessory

may contact hidden wiring or its own cord. Cutting

accessory contacting a „live“ wire may make exposed metal

parts of the power tool „live“ and could give the operator an

electric shock.

Appliances used at many different locations including open

air should be connected via a residual current device of

30 mA or less.

Always wear goggles when using the machine. It is

recommended to wear gloves, sturdy non slipping shoes and

apron.

Sawdust and splinters must not be removed while the

machine is running.

Always disconnect the plug from the socket before carrying

out any work on the machine.

Only plug-in when machine is switched off.

Keep mains lead clear from working range of the machine.

Always lead the cable away behind you.

When working in walls ceiling, or oor, take care to avoid

electric cables and gas or waterpipes.

The dust produced when using this tool may be harmful to

health. Do not inhale the dust. Wear a suitable dust

protection mask.

Under the effect of extreme electromagnetic interferences

from the outside, temporary variations in the speed of

rotation could arise in particular cases.

SPECIFIED CONDITIONS OF USE

The rotary pneumatic hammer can be used for hammer

drilling and drilling in wood, metal as well as plastic.

Do not use this product in any other way as stated for normal

use.

MAINS CONNECTION

Connect only to single-phase a.c. current and only to the

system voltage indicated on the rating plate. It is also

possible to connect to sockets without an earthing contact as

the design conforms to safety class II.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all

times.

Important note! If the carbon brushes are worn, in addition to

exchanging the brushes the tool should be sent to after-

sales service. This will ensure long service life and top

performance.

Use only Milwaukee accessories and spare parts. Should

components need to be replaced which have not been

described, please contact one of our Milwaukee service

agents.

SYMBOLS

Please read the instructions carefully before

starting the machine.

Always wear hearing protection when using the

machine.

Always wear goggles when using the machine.

Seal of Electrical Security

Always disconnect the plug from the socket before

carrying out any work on the machine.

Accessory - Not included in standard equipment,

available as an accessory.

Do not dispose of electric tools together with

household waste material! In observance of

European Directive 2002/96/EC on waste electrical

and electronic equipment and its implementation in

accordance with national law, electric tools that

have reached the end of their life must be collected

separately and returned to an environmentally

compatible recycling facility.

Class II construction, tool in which protection

against electric shock does not rely on basic

insulation only, but in which additional safety

precautions, such as double insulation or reinforced

insulation, are provided.

22

LIMITED WARRANTY - USA AND CANADA

Every MILWAUKEE power tool (including cordless product – tool, battery pack(s) - see separate & distinct CORD-

LESS BATTERY PACK LIMITED WARRANTY statements & battery charger and Work Lights*) is warranted to

the original purchaser only to be free from defects in material and workmanship. Subject to certain exceptions,

MILWAUKEE will repair or replace any part on an electric power tool which, after examination, is determined by

MILWAUKEE to be defective in material or workmanship for a period of ve (5) years* after the date of purchase

unless otherwise noted. Return of the power tool to a MILWAUKEE factory Service Center location or MILWAUKEE

Authorized Service Station, freight prepaid and insured, is required. A copy of the proof of purchase should be

included with the return product. This warranty does not apply to damage that MILWAUKEE determines to be from

repairs made or attempted by anyone other than MILWAUKEE authorized personnel, misuse, alterations, abuse,

normal wear and tear, lack of maintenance, or accidents.

*The warranty period for, Job Site Radios, M12™ Power Port, M18™ Power Source, and Trade Titan™ Industrial

Work Carts is one (1) year from the date of purchase. The warranty period for a LED Work Light and LED Upgrade

Bulb is a limited LIFETIME warranty to the original purchaser only, if during normal use the LED bulb fails the Work

Light or Upgrade Bulb will be replaced free of charge.

*This warranty does not cover Air Nailers & Stapler, Airless Paint Sprayer, Cordless Battery Packs, Gasoline Driven

Portable Power Generators, Hand Tools, Hoist – Electric, Lever & Hand Chain, M12™ Heated Jackets, Reconditioned

product and Test & Measurement products. There are separate and distinct warranties available for these products.

Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE power tool product.

The manufacturing date of the product will be used to determine the warranty period if no proof of purchase is

provided at the time warranty service is requested.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A

CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT

AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAU-

KEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY

COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY

DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS

FOR LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL

OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL.

TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING

WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WAR-

RANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED

ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO

THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,

AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

This warranty applies to product sold in the U.S.A. and Canada only.

Please consult the ‘Service Center Search’ in the Parts & Service section of MILWAUKEE’s website www.mil-

waukeetool.com or call 1.800.SAWDUST (1.800.729.3878) to locate your nearest service facility for warranty and

non-warranty service on a Milwaukee electric power tool.

23

MILWAUKEE ELECTRIC TOOL CORPORATION

58-14-5264d4 08/12 Impreso en China

961075216-01( )

Importado por:

Techtronic Industries Comércio de

Ferramentas do Brasil Ltda.

Prolongamento da Travessa Claudio Armando,

nº 171, Bloco 2, galpão 21.

Bairro Assunção, São Bernardo do Campo, SP.

CEP: 09861-730 – Brasil

CNPJ: 11.857.988/0001-26

Importado por:

Techtronic Ind Argentina SRL

Cuit: 33-71069847-9

Av. Leandro N. Alem 110 piso 13

C.A.B.A (1001), BUENOS AIRES

ARGENTINA

Milwaukee SDS PLUS 5263-59A, 5263-59, 5263-59A, 5263-59B, SDS PLUS 5263-59, SDS PLUS 5263-59B User manual

Related papers

Other documents