COMFORT-AIRE VMH36SD-1-CY Owner's manual

Brand: COMFORT-AIRE

Model: VMH36SD-1-CY

Type: Owner's manual

Heat Controller • 1900 Wellworth Ave. • Jackson, MI 49203 • (517)787-2100 • www.heatcontroller.com

REMOTE CONTROLLER

MANUAL

VMH 30/36 SD Series

Inverter Single Zone

Ductless Mini-Split

Heat Controller

TABLE OF CONTENTS

 BatteriesandBatterySpecications/Replacement........................................................ 3

 SpecicationsandFeatures .......................................................................................... 4

 Functions ....................................................................................................................... 5

 RemoteControlDisplay ................................................................................................. 8

 RemoteOperations ....................................................................................................... 9

VMH 30/36 SD Remote Controller

Heat Controller

Remote Control Instructions

Battery Specication

1.Theremotecontrollercanbeusedtocontrolandoperatetheunit

2.Theremote’ssignalcantransmitupto26ft.(8m)away.

3.Anyobstructionsbetweenthesignaloftheremotecontrolandthe

indoorunitcaninterfere,limitingthecapacityofthesignal.

4.Whenabuttonispressedontheremotecontrol,theindoorunit

willemita“beep”,whichindicatesthatthecommandhasbeen

receivedandtransmittedtotheindoorunit.

Tousetheremotecontrol,itisnecessarytoinstalltwo(R03/LR03x2)alkalineAAAbatteries.

Battery Replacement

1.Batteriesshouldbereplacedwhenthereisnota“beep”heardfromtheindoorunitorthesignal

indicatorlightdoesnotilluminatewhenbuttonsarepressedontheremoteorwhentheindoorunit

doesnotrespondtotheremotecontrolscommands.

2.Toreplacethebatteries:

A.Removethecoverbypressingandslidingoff.

B.Removetheoldbatteriesandinsertthenewbatteries,placingthe(+)and(-)endscorrectly.

C.Reattachthecoverbyslidingitbackintoposition.

NOTE:Whenthebatteriesareremoved,theremotecontrollererasesallusersettings.Afterinserting

newbatteries,theremotecontrollermustbereprogrammedforanyuserspecicsettings.

•Theairconditionerwillnotoperateifcurtains,doorsorothermaterialsblockthesignalfromthe

remotecontroltotheunit.

•Avoidspillinganyliquidintotheremote.

•Donotexposetodirectsunlightorheat.

•Iftheinfraredsignalreceiverontheindoorunitisexposedtodirectsunlight,theairconditioner

maynotfunctionproperly.Usecurtainstopreventthesunlightfrominterferringwiththe

receiver’ssignal.

•Ifotherelectricalappliancessignalsreacttothesignalsentbytheremotecontrollerrelocate

these appliances.

•Whenreplacingbatteries,donotuseoldbatteries

•Ifyoudonotusetheremoteforaprolongedperiodoftime,removethebatteries.Otherwise

theymayleakanddamagetheremote

26 ft.(8 m)

CAUTION

VMH 30/36 SD Remote Controller

Heat Controller

Remote Controller Specications

Performance Features

Model RG52A1/BGEFU1

RatedVoltage 3.0V

SignalTransmissionDistance 26ft(8m)withfullbatteries

OperatingEnvironment

23°F~140°F(-5~60°F)

1.OperatingModes:AUTO,COOL,DRY,HEAT

 (heatpumpmodelsonly)andFAN.

2.24hourtimer

3.TemperatureRangeSelection:62°F~86°F.

4.LCD(LiquidCrystalDisplay)

NOTE:Remotecontrollercanbesettodisplaydegreesin°C

or°F.Toalternatebetweenunitofmeasure,pressandhold

thetempandbuttonatthesametime.Release

buttonswhentheunitofmeasurechanges.Repeatthe

processtorevertbacktothepreviousunitofmeasure.

VMH 30/36 SD Remote Controller

Heat Controller

ON/OFF

Pressthisbuttontopoweron,whichstartstheunit’s

operation.Pushthebuttonagaintopoweroff,which

stopstheunit’soperation.

MODE

Eachtimethisbuttonispressed,amodeisselectedin

asequenceofAUTO,COOL,DRY,HEAT*,andFAN

then repeat.

*Heat mode is applicable to heat pump models only.

FAN

Presstoselectthefanspeedinfourintervals:

SLEEP

PressthisbuttontoactivatetheSLEEPmode.Pressit

againtodeactivate.Thisfeaturecanonlybeselected

whentheunitisinCOOL,HEAT*,orDrymode.Usethis

featureforthemostcomfortabletemperaturecontrol

whileyousleepandyourbodytemperaturerises.

*Heat mode is applicable to heat pump models only.

TURBO

ActivatesordeactivatestheTurbofunction.Pressthis

buttonforTurbofunction.Turbofunctionenablesthe

unittoreachthesettemperatureintheshortesttime.In

thecoolingmode,theunitwillblowcoldairatasuper

highfanspeed.Inheatingmode*,theunitwillblowhot

airasuperhighfanspeed.

*Heat mode is applicable to heat pump models only.

SELF CLEAN

Thisfunctionhelpstokeeptheinsideoftheunitdryand

preventsmoldfromforming.Itisparticularlyusefulat

theendoftheseasonwhentheunitwillnotbeinuse

foralongperiodoftime.Presstheselfcleanbuttonto

initiatetheselfcleaningfunction.

Functions

VMH 30/36 SD Remote Controller

Heat Controller

TEMP UP ( )

Pushthisbuttontoincreasetheindoortemperatureset

pointin1°Fincrementsupto86°F.

TEMP DOWN ( )

Pushthisbuttontodecreasetheindoortemperatureset

pointin1°Fincrementsdownto62°F.

SHORTCUT

• Usedtorestorethecurrentsettingsorresumethe

previous setting.

• Thersttimetheunitispoweredonandthe

SHORTCUTbuttonispressed,theunitwilloperatein

AUTOmode,80°Fsettemp,andautofanspeed.

• Pushingthisbuttonwillautomaticallyrevertbackto

theprevioussettingsincludingoperatingmode,set

temperature,fanspeedlevelandsleepfeature(if

activated)andtransmitthesignaltotheunit.

• Whenthisbuttonispressedformorethan2

seconds,thesystemwillautomaticallyrestorethe

currentoperationsettingsincludingoperatingmode,

settemperatures,fanspeedandsleepfeature(if

activated).

TIMER ON

Pressthebuttontoinitiatetheauto-ontimersequence.

Eachpresswillincreasetheauto-ontimersettingin

30minutesincrements.Whenthesettimedisplays10,

eachadditiontimethebuttonispressed,itwillincrease

theauto-ontimersettingin60minuteincrements.To

canceltheauto-ontimerprogram,simplyadjustthe

auto-ontimeto0.0.

Functions

VMH 30/36 SD Remote Controller

Heat Controller

TIMER OFF

Pressthebuttontoinitiatetheauto-offtimersequence.

Eachpresswillincreasetheauto-timersettingin

30minutesincrements.Whenthesettimedisplays

10,eachadditionaltimethebuttonispresseditwill

increasetheauto-timersettingin60minuteincrements.

Tocanceltheauto-timerprogram,simplyadjustthe

auto-offtimerto0.0.

DIRECT

Pressthisbuttontodirecttheairowbyselectingthe

positionofthelouverontheunit.Eachtimethebutton

ispressedthelouverwillopen/closeby6°increments.

NOTE: If the louver moves in a position that could affect

the cooling or heating (heat pump models only) of the

air conditioner, the unit will alter the direction of the

louver angle automatically.

SWING

Pressthisbuttontostart/stoptheautoswingfeature,

whichthelouveroscillatesupanddown.

NOTE: If the louver oscillates or moves in a position

that could affect heating (heat pump models only) or

cooling of the air conditioner, the unit will automatically

adjust the louver position.

FOLLOW ME

PushthisbuttontoinitiatetheFollowMemode.In

followmemode,thetemperaturesensorbuiltintothe

remotecontrolsensestheroomtemperatureinplaceof

thesensorinsidetheindoorunit.Thisallowstheremote

controltocontrolthetemperatureoftheroomwhere

itispresent.Thisfeaturehelpspreventtemperature

stratication.Wheninfollowmemode,theremote

controldisplaywillshowtheactualroomtemperatureit

senses.

LED

Disables/Activatestheindoor\Display.Whenpushing

thebutton,theindoorscreeniscleared,pressitagain

toturnonthelightofthedisplay.

Functions

VMH 30/36 SD Remote Controller

Heat Controller

MODE

Displaysthecurrentoperationmode.Includingauto(),

cool(),dry(),heat*(),fan()andbackto

auto().

*Applicable to heat pump models only

TRANSMISSION INDICATOR

Thistransmissionindicatorlightswhenremotecontroller

transmitssignalstotheindoorunit.

ON/OFF

Showswhenunitison.

TIMER ON

DisplayswhenTIMERONtimeisset.

TIMER OFF

DisplayswhenTIMEROFFtimeisset.

SLEEP

DisplayswheninSLEEPMODE.

FOLLOW ME

DisplayedwhenFOLLOWMEfunctionisactivated.

TEMP./TIMER DISPLAY

Displaysthesettemperature(62°F~86°F).Whenthe

operatingmodeissettoFAN,nosettemperatureis

displayed.InTIMERmode,settheONandOFFtimesettings

are displayed.

FAN

DisplaystheFANspeed,AUTO(nodisplay)andthree

fanspeedlevels“”(LOW)“”

(MED)“”(HIGH)canbeindicated.Thefan

speedisAUTOwhentheoperatingmodeisinAUTOorDRY.

Remote Control Display

VMH 30/36 SD Remote Controller

Heat Controller

AUTO OPERATION

1.PresstheMODEbuttontoselectAuto.

2.PresstheUP/DOWNbuttontosetthedesired

temperature.Thetemperaturecanbesetwithina

rangeof62°F~86°Fin1°Fincrements.

• InAutomode,theunitwillautomaticallyselect

Cool,FanorHeat*modesbesensingthe

differencebetweentheactualambientroom

temperatureandthesettemperatureontheremote

controller.

• IntheAutomode,youcannotchargethefan

speed.Itisbeingautomaticallycontrolled.

COOLING/HEATING/FAN OPERATION

IfAutomodeisuncomfortable,youcanmanually

overridethesettingbyputtingtheunitinCOOL,HEAT*,

orFAN**ONLYmode.

1.PresstheMODEbuttontoselectCOOL,HEAT*

(pump)orFAN**mode.

2.PressthetempUP/DOWNbuttontosetthedesired

temperature.Thetemperaturecanbesetwithina

rangeof62°F~86°Fin1°Fincrements.

3.PresstheFANbuttontoselectthefanspeedinfour

steps-Auto,Low,Med,orHigh.

NOTE

* Heat mode is applicable to heat pump models only.

** In the FAN mode, the set temperature is not

displayed on the remote controller and you are not

able to control the room temperature either. In this

case, only the fan speed can be changed.

Remote Operation

VMH 30/36 SD Remote Controller

Heat Controller

DRY OPERATION

TheDRYmodewillautomaticallyselecttheamountof

dehumidicationbasedonthedifferencebetweenthe

settemperatureandactualroomtemperature.Thefan

speedisautomaticallysettolow.

1.PresstheMODEbuttontoselectDRYmode.

2.PresstheUP/DOWNbuttonstosetthedesired

temperature.Thetemperaturecanbesetwithina

rangeof62°F~86°Fin1°Fincrements.

NOTE

• In the Dry mode, you can not change the fan speed. It

is ceing automatically controlled.

• Due to the difference between the set temperature

and the actual room temperature, the unit will

automatically switch between COOL and FAN only

mode while in DRY mode.

ADJUSTING AIR FLOW DIRECTION

UsetheSWINGorDIRECTbuttontoadjustthedesired

airowdirection.

1.WhentheDIRECTbuttonispushedthehorizontal

louverchangesin6°degreeangleincrements.

2.WhentheSWINGbuttonispushedthelouver

oscillates.

NOTE

When the louver oscillates or moves in a position that

could affect the cooling or heating (heat pump models

only) of the air conditioner, the unit will automatically

change the louver direction.

Remote Operation

VMH 30/36 SD Remote Controller

Heat Controller

TIMER OPERATION

PresstheTIMERONbuttontosetthetimetheunit

shouldautomaticallyturnon.PresstheTIMEROFF

buttontosetthetimetheunitshouldautomaticallyturn

off.

1.PresstheTIMERONbutton.Theremotecontroller

showTIMERON,thelastAuto-onsettimeandthe

“H”iconwillbeshownontheLCDdisplay.Nowitis

readytoresettheAuto-ontimetoSTARToperation.

2.PushtheTIMERONbuttonagaintosetdesiredAuto-

ontime.Eachtimeyoupressthebutton,thetime

increasesbyhalfanhourbetween0and10hours

andbyonehourbetween10and24hours.

3.AftersettingtheTIMERON,therewillbeaone

seconddelaybeforetheremotecontrollertransmits

thesignaltotheairconditioner.Then,after

approximatelyanother2seconds,the“H”iconwill

disappearandthesettemperaturewillre-appearon

theLCDdisplay.

TO SET THE AUTO-OFF TIME

1.PressTIMEROFFbutton.Theremotecontroller

showTIMEROFF,thelastAuto-offsettingtime

andthe“H”iconwillbeshownontheLCDdisplay

area.NowitisreadytoresettheLCDdisplayarea.

NowitisreadytoresettheAuto-offtimetostopthe

operation.

2.PushtheTIMEROFFbuttonagaintosetdesired

Auto-offtime.Eachtimeyoupressthebutton,the

timeincreasesbyhalfanhourbetween0and10

hoursandbyonehourbetween10and24hours.

3.AftersettingtheTIMEROFF,therewillbeaone

seconddelaybeforetheremotecontrollertransmits

thesignaltotheairconditioner.Then,after

approximatelyanother2seconds,thesignal“H”will

disappearandsetthetemperaturewillre-appearon

theLCDdisplay.

Remote Operation

VMH 30/36 SD Remote Controller

Heat Controller

SLEEP FUNCTION

Thesleepfunctionenablestheunittoautomatically

changethetemperatureby2°Fperhourforthersttwo

hours,thenwillremainsteadyforthenext5hours,after

thattheunitwillstopoperating.SLEEPmodecreates

comfortabletemperaturesandsavesenergy.

1.WhentheSLEEPmodeisselectedwhileinCOOL

mode,thetemperatureincreasestocreatethe

mostuncomfortableconditionswhileyourbody

temperatureriseswhenyousleep.WhenSLEEP

isselectedwhileinHEAT*mode,thetemperature

deceasestoensureyoudon’tgettoohotwhileyour

bodytemperatureriseswhenyousleep.

NOTE

The SLEEP function is only selectable when

the unit is in COOL, HEAT* or AUTO modes.

* Heat mode is applicable to heat pump models only.

Remote Operation

VMH 30/36 SD Remote Controller

Heat Controller VMH 30/36 SD Remote Controller

Heat ControllerVMH 30/36 SD Remote Controller

Heat Controller VMH 30/36 SD Remote Controller

VMH 09,12,18,24 SD Remote Controller Heat Controller

:HOOZRUWK$YH-DFNVRQ0,3KZZZKHDWFRQWUROOHUFRP





'XHWRRQJRLQJSURGXFWLPSURYHPHQWVVSHFLILFDWLRQVDQGGLPHQVLRQVDUH

VXEMHFWWRFKDQJHDQGFRUUHFWLRQZLWKRXWQRWLFHRULQFXUULQJREOLJDWLRQV'HWHUPLQLQJWKH

DSSOLFDWLRQDQGVXLWDELOLW\IRUXVHRIDQ\SURGXFWLVWKHUHVSRQVLELOLW\RIWKHLQVWDOOHU

$GGLWLRQDOO\WKHLQVWDOOHULVUHVSRQVLEOHIRUYHULI\LQJGLPHQVLRQDOGDWDRQWKHDFWXDOSURGXFW

SULRUWREHJLQQLQJDQ\LQVWDOODWLRQSUHSDUDWLRQV

,QFHQWLYHDQGUHEDWHSURJUDPVKDYHSUHFLVHUHTXLUHPHQWVDVWRSURGXFWSHUIRUPDQFH

DQGFHUWLILFDWLRQ$OOSURGXFWVPHHWDSSOLFDEOHUHJXODWLRQVLQHIIHFWRQGDWHRIPDQXIDFWXUH

KRZHYHUFHUWLILFDWLRQVDUHQRWQHFHVVDULO\JUDQWHGIRUWKHOLIHRIDSURGXFW

7KHUHIRUHLWLVWKHUHVSRQVLELOLW\RIWKHDSSOLFDQWWRGHWHUPLQHZKHWKHUDVSHFLILF

PRGHOTXDOLILHVIRUWKHVHLQFHQWLYHUHEDWHSURJUDPV

12/2013

COMFORT-AIRE VMH36SD-1-CY Owner's manual

COMFORT-AIRE VMH36SD-1-CY Owner's manual

COMFORT-AIRE VMH36SD-1-CY Owner's manual

Related papers

Other documents