2. Heat Controller
  3. DVC/DVH SERIES

Heat Controller DVC/DVH SERIES, Fan DVC/DVH SERIES User manual

  • Hello! I am an AI chatbot trained to assist you with the Heat Controller DVC/DVH SERIES User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Heat Controller • 1900 Wellworth Ave. • Jackson, MI 49203 • (517)787-2100 • www.heatcontroller.com
REMOTE CONTROLLER
MANUAL
DVC/DVH Series
Inverter Single Zone
Ductless Mini-Split
2
DVC/DVH Remote Controller Heat Controller
TABLE OF CONTENTS
BatteriesandBatterySpecications/Replacement........................................................ 3
SpecicationsandFeatures .......................................................................................... 4
Functions ....................................................................................................................... 5
RemoteControlDisplay ................................................................................................. 8
RemoteOperations ....................................................................................................... 9
3
Heat Controller DVC/DVH Remote Controller
Remote Control Instructions
Battery Specication
1.Theremotecontrollercanbeusedtocontrolandoperatetheunit
2.Theremote’ssignalcantransmitupto26ft.(8m)away.
3.Anyobstructionsbetweenthesignaloftheremotecontrolandthe
indoorunitcaninterfere,limitingthecapacityofthesignal.
4.Whenabuttonispressedontheremotecontrol,theindoorunit
willemita“beep”,whichindicatesthatthecommandhasbeen
receivedandtransmittedtotheindoorunit.
Tousetheremotecontrol,itisnecessarytoinstalltwo(R03/LR03x2)alkalineAAAbatteries.
Battery Replacement
1.Batteriesshouldbereplacedwhenthereisnota“beep”heardfromtheindoorunitorthesignal
indicatorlightdoesnotilluminatewhenbuttonsarepressedontheremoteorwhentheindoorunit
doesnotrespondtotheremotecontrolscommands.
2.Toreplacethebatteries:
A.Removethecoverbypressingandslidingoff.
B.Removetheoldbatteriesandinsertthenewbatteries,placingthe(+)and(-)endscorrectly.
C.Reattachthecoverbyslidingitbackintoposition.
NOTE:Whenthebatteriesareremoved,theremotecontrollererasesallusersettings.Afterinserting
newbatteries,theremotecontrollermustbereprogrammedforanyuserspecicsettings.
•Theairconditionerwillnotoperateifcurtains,doorsorothermaterialsblockthesignalfromthe
remotecontroltotheunit.
•Avoidspillinganyliquidintotheremote.
•Donotexposetodirectsunlightorheat.
•Iftheinfraredsignalreceiverontheindoorunitisexposedtodirectsunlight,theairconditioner
maynotfunctionproperly.Usecurtainstopreventthesunlightfrominterferringwiththe
receiver’ssignal.
•Ifotherelectricalappliancessignalsreacttothesignalsentbytheremotecontrollerrelocate
these appliances.
•Whenreplacingbatteries,donotuseoldbatteries
•Ifyoudonotusetheremoteforaprolongedperiodoftime,removethebatteries.Otherwise
theymayleakanddamagetheremote
26 ft.(8 m)
!
CAUTION
4
DVC/DVH Remote Controller Heat Controller
Remote Controller Specications
Performance Features
Model RG52B/BGEU
RatedVoltage 3.0V
SignalTransmissionDistance 26ft(8m)withfullbatteries
OperatingEnvironment
23°F~140°F(-5~60°F)
1.OperatingModes:AUTO,COOL,DRY,HEAT
(heatpumpmodelsonly)andFAN.
2.24hourtimer
3.TemperatureRangeSelection:62°F~86°F.
4.LCD(LiquidCrystalDisplay)
NOTE:Remotecontrollercanbesettodisplaydegreesin°C
or°F.Toalternatebetweenunitofmeasure,pressandhold
thetempandbuttonatthesametime.Release
buttonswhentheunitofmeasurechanges.Repeatthe
processtorevertbacktothepreviousunitofmeasure.
5
Heat Controller DVC/DVH Remote Controller
ON/OFF
Pressthisbuttontopoweron,whichstartstheunit’s
operation.Pushthebuttonagaintopoweroff,which
stopstheunit’soperation.
MODE
Eachtimethisbuttonispressed,amodeisselectedin
asequenceofAUTO,COOL,DRY,HEAT*,andFAN
then repeat.
*Heat mode is applicable to heat pump models only.
FAN
Presstoselectthefanspeedinfourintervals:
SLEEP
PressthisbuttontoactivatetheSLEEPmode.Pressit
againtodeactivate.Thisfeaturecanonlybeselected
whentheunitisinCOOL,HEAT*,orDrymode.Usethis
featureforthemostcomfortabletemperaturecontrol
whileyousleepandyourbodytemperaturerises.
*Heat mode is applicable to heat pump models only.
TURBO
ActivatesordeactivatestheTurbofunction.Pressthis
buttonforTurbofunction.Turbofunctionenablesthe
unittoreachthesettemperatureintheshortesttime.In
thecoolingmode,theunitwillblowcoldairatasuper
highfanspeed.Inheatingmode*,theunitwillblowhot
airasuperhighfanspeed.
*Heat mode is applicable to heat pump models only.
SELF CLEAN
Thisfunctionhelpstokeeptheinsideoftheunitdryand
preventsmoldfromforming.Itisparticularlyusefulat
theendoftheseasonwhentheunitwillnotbeinuse
foralongperiodoftime.Presstheselfcleanbuttonto
initiatetheselfcleaningfunction.
Functions
1
2
3
4
5
6
*
6
DVC/DVH Remote Controller Heat Controller
TEMP UP ( )
Pushthisbuttontoincreasetheindoortemperatureset
pointin1°Fincrementsupto86°F.
TEMP DOWN ( )
Pushthisbuttontodecreasetheindoortemperatureset
pointin1°Fincrementsdownto62°F.
SHORTCUT
• Usedtorestorethecurrentsettingsorresumethe
previous setting.
• Thersttimetheunitispoweredonandthe
SHORTCUTbuttonispressed,theunitwilloperatein
AUTOmode,80°Fsettemp,andautofanspeed.
• Pushingthisbuttonwillautomaticallyrevertbackto
theprevioussettingsincludingoperatingmode,set
temperature,fanspeedlevelandsleepfeature(if
activated)andtransmitthesignaltotheunit.
• Whenthisbuttonispressedformorethan2
seconds,thesystemwillautomaticallyrestorethe
currentoperationsettingsincludingoperatingmode,
settemperatures,fanspeedandsleepfeature(if
activated).
TIMER ON
Pressthebuttontoinitiatetheauto-ontimersequence.
Eachpresswillincreasetheauto-ontimersettingin
30minutesincrements.Whenthesettimedisplays10,
eachadditiontimethebuttonispressed,itwillincrease
theauto-ontimersettingin60minuteincrements.To
canceltheauto-ontimerprogram,simplyadjustthe
auto-ontimeto0.0.
Functions
7
8
9
7
Heat Controller DVC/DVH Remote Controller
TIMER OFF
Pressthebuttontoinitiatetheauto-offtimersequence.
Eachpresswillincreasetheauto-timersettingin
30minutesincrements.Whenthesettimedisplays
10,eachadditionaltimethebuttonispresseditwill
increasetheauto-timersettingin60minuteincrements.
Tocanceltheauto-timerprogram,simplyadjustthe
auto-offtimerto0.0.
DIRECT
Pressthisbuttontodirecttheairowbyselectingthe
positionofthelouverontheunit.Eachtimethebutton
ispressedthelouverwillopen/closeby6°increments.
NOTE: If the louver moves in a position that could affect
the cooling or heating (heat pump models only) of the
air conditioner, the unit will alter the direction of the
louver angle automatically.
SWING
Pressthisbuttontostart/stoptheautoswingfeature,
whichthelouveroscillatesupanddown.
NOTE: If the louver oscillates or moves in a position
that could affect heating (heat pump models only) or
cooling of the air conditioner, the unit will automatically
adjust the louver position.
FOLLOW ME
PushthisbuttontoinitiatetheFollowMemode.In
followmemode,thetemperaturesensorbuiltintothe
remotecontrolsensestheroomtemperatureinplaceof
thesensorinsidetheindoorunit.Thisallowstheremote
controltocontrolthetemperatureoftheroomwhere
itispresent.Thisfeaturehelpspreventtemperature
stratication.Wheninfollowmemode,theremote
controldisplaywillshowtheactualroomtemperatureit
senses.
LED
Disables/Activatestheindoor\Display.Whenpushing
thebutton,theindoorscreeniscleared,pressitagain
toturnonthelightofthedisplay.
Functions
10
11
12
13
14
8
DVC/DVH Remote Controller Heat Controller
MODE
Displaysthecurrentoperationmode.Includingauto(),
cool(),dry(),heat*(),fan()andbackto
auto().
*Applicable to heat pump models only
TRANSMISSION INDICATOR
Thistransmissionindicatorlightswhenremotecontroller
transmitssignalstotheindoorunit.
ON/OFF
Showswhenunitison.
TIMER ON
DisplayswhenTIMERONtimeisset.
TIMER OFF
DisplayswhenTIMEROFFtimeisset.
SLEEP
DisplayswheninSLEEPMODE.
FOLLOW ME
DisplayedwhenFOLLOWMEfunctionisactivated.
TEMP./TIMER DISPLAY
Displaysthesettemperature(62°F~86°F).Whenthe
operatingmodeissettoFAN,nosettemperatureis
displayed.InTIMERmode,settheONandOFFtimesettings
are displayed.
FAN
DisplaystheFANspeed,AUTO(nodisplay)andthree
fanspeedlevels“”(LOW)“”
(MED)“”(HIGH)canbeindicated.Thefan
speedisAUTOwhentheoperatingmodeisinAUTOorDRY.
Remote Control Display
9
Heat Controller DVC/DVH Remote Controller
AUTO OPERATION
1.PresstheMODEbuttontoselectAuto.
2.PresstheUP/DOWNbuttontosetthedesired
temperature.Thetemperaturecanbesetwithina
rangeof62°F~86°Fin1°Fincrements.
• InAutomode,theunitwillautomaticallyselect
Cool,FanorHeat*modesbesensingthe
differencebetweentheactualambientroom
temperatureandthesettemperatureontheremote
controller.
• IntheAutomode,youcannotchargethefan
speed.Itisbeingautomaticallycontrolled.
COOLING/HEATING/FAN OPERATION
IfAutomodeisuncomfortable,youcanmanually
overridethesettingbyputtingtheunitinCOOL,HEAT*,
orFAN**ONLYmode.
1.PresstheMODEbuttontoselectCOOL,HEAT*
(pump)orFAN**mode.
2.PressthetempUP/DOWNbuttontosetthedesired
temperature.Thetemperaturecanbesetwithina
rangeof62°F~86°Fin1°Fincrements.
3.PresstheFANbuttontoselectthefanspeedinfour
steps-Auto,Low,Med,orHigh.
NOTE
* Heat mode is applicable to heat pump models only.
** In the FAN mode, the set temperature is not
displayed on the remote controller and you are not
able to control the room temperature either. In this
case, only the fan speed can be changed.
Remote Operation
10
DVC/DVH Remote Controller Heat Controller
DRY OPERATION
TheDRYmodewillautomaticallyselecttheamountof
dehumidicationbasedonthedifferencebetweenthe
settemperatureandactualroomtemperature.Thefan
speedisautomaticallysettolow.
1.PresstheMODEbuttontoselectDRYmode.
2.PresstheUP/DOWNbuttonstosetthedesired
temperature.Thetemperaturecanbesetwithina
rangeof62°F~86°Fin1°Fincrements.
NOTE
• In the Dry mode, you can not change the fan speed. It
is ceing automatically controlled.
• Due to the difference between the set temperature
and the actual room temperature, the unit will
automatically switch between COOL and FAN only
mode while in DRY mode.
ADJUSTING AIR FLOW DIRECTION
UsetheSWINGorDIRECTbuttontoadjustthedesired
airowdirection.
1.WhentheDIRECTbuttonispushedthehorizontal
louverchangesin6°degreeangleincrements.
2.WhentheSWINGbuttonispushedthelouver
oscillates.
NOTE
When the louver oscillates or moves in a position that
could affect the cooling or heating (heat pump models
only) of the air conditioner, the unit will automatically
change the louver direction.
Remote Operation
1
2
11
Heat Controller DVC/DVH Remote Controller
TIMER OPERATION
PresstheTIMERONbuttontosetthetimetheunit
shouldautomaticallyturnon.PresstheTIMEROFF
buttontosetthetimetheunitshouldautomaticallyturn
off.
1.PresstheTIMERONbutton.Theremotecontroller
showTIMERON,thelastAuto-onsettimeandthe
“H”iconwillbeshownontheLCDdisplay.Nowitis
readytoresettheAuto-ontimetoSTARToperation.
2.PushtheTIMERONbuttonagaintosetdesiredAuto-
ontime.Eachtimeyoupressthebutton,thetime
increasesbyhalfanhourbetween0and10hours
andbyonehourbetween10and24hours.
3.AftersettingtheTIMERON,therewillbeaone
seconddelaybeforetheremotecontrollertransmits
thesignaltotheairconditioner.Then,after
approximatelyanother2seconds,the“H”iconwill
disappearandthesettemperaturewillre-appearon
theLCDdisplay.
TO SET THE AUTO-OFF TIME
1.PressTIMEROFFbutton.Theremotecontroller
showTIMEROFF,thelastAuto-offsettingtime
andthe“H”iconwillbeshownontheLCDdisplay
area.NowitisreadytoresettheLCDdisplayarea.
NowitisreadytoresettheAuto-offtimetostopthe
operation.
2.PushtheTIMEROFFbuttonagaintosetdesired
Auto-offtime.Eachtimeyoupressthebutton,the
timeincreasesbyhalfanhourbetween0and10
hoursandbyonehourbetween10and24hours.
3.AftersettingtheTIMEROFF,therewillbeaone
seconddelaybeforetheremotecontrollertransmits
thesignaltotheairconditioner.Then,after
approximatelyanother2seconds,thesignal“H”will
disappearandsetthetemperaturewillre-appearon
theLCDdisplay.
Remote Operation
1
12
DVC/DVH Remote Controller Heat Controller
SLEEP FUNCTION
Thesleepfunctionenablestheunittoautomatically
changethetemperatureby2°Fperhourforthersttwo
hours,thenwillremainsteadyforthenext5hours,after
thattheunitwillstopoperating.SLEEPmodecreates
comfortabletemperaturesandsavesenergy.
1.WhentheSLEEPmodeisselectedwhileinCOOL
mode,thetemperatureincreasestocreatethe
mostuncomfortableconditionswhileyourbody
temperatureriseswhenyousleep.WhenSLEEP
isselectedwhileinHEAT*mode,thetemperature
deceasestoensureyoudon’tgettoohotwhileyour
bodytemperatureriseswhenyousleep.
NOTE
The SLEEP function is only selectable when
the unit is in COOL, HEAT* or AUTO modes.
* Heat pump is applicable to heat pump models only.
Remote Operation
1
13
Heat Controller DVC/DVH Remote Controller
14
DVC/DVH Remote Controller Heat Controller
15
Heat Controller DVC/DVH Remote Controller
16
DVC/DVH Remote Controller Heat Controller
:HOOZRUWK$YH-DFNVRQ0,3KZZZKHDWFRQWUROOHUFRP

07/2013
Design, material, performance specications and components
subject to change without notice.
/