Vents SRS-1 User manual

Vents
Brand
Vents
Model
SRS-1
Type
User manual

Vents SRS-1 is a sensor speed controller that allows you to control the speed of ventilation units and domestic fans. It is equipped with a sensitive sensor panel made of hardened glass, with the button and two buttons for speed control from minimum to maximum value. The speed controller has a power supply voltage of 230 V/50-60 Hz and a maximum load current of 1 A. It has a temperature range of -10 up to +45 °C and a humidity range of 5-80% (no condensation). The service life is 100,000 switching operations and the Ingress Protection Rating is IP 30. The weight is 138 g.

Vents SRS-1 is a sensor speed controller that allows you to control the speed of ventilation units and domestic fans. It is equipped with a sensitive sensor panel made of hardened glass, with the button and two buttons for speed control from minimum to maximum value. The speed controller has a power supply voltage of 230 V/50-60 Hz and a maximum load current of 1 A. It has a temperature range of -10 up to +45 °C and a humidity range of 5-80% (no condensation). The service life is 100,000 switching operations and the Ingress Protection Rating is IP 30. The weight is 138 g.

Sensor speed controller
SRS-1
DESCRIPTION
The speed controller is equipped with a sensitive sensor panel made of hardened glass, with the
button and two buttons for speed control from minimum ( ) to maximum value ( ).
MOUNTING
WARNING!
Make sure that the speed controller is not damaged. Do not operate a damaged speed controller! Do not install the speed controller on an
uneven surface! Do not apply excessive forces to avoid the product deformation.
Mounting sequence of the sensor speed controller:
Unfasten gently the front panel latches of the speed controller.
Unfasten gently the front panel latches of the speed controller.
Route the cable in the wall to the panel mounting place.
Attach the back panel to the wall or in the mounting box through the fastening openings.
Install the front panel on the latches.
86
62
4
52
86 31
21
R1,5
11
58
OUTOUT OUTOUT IN
LL1L2L3L4
Sensor speed controller mounting
OVERALL AND CONNECTING DIMENSIONS
Speed controller outline drawing
TECHNICAL DATA
Power supply voltage [V/Hz] 230 / 50-60
Maximum load current [A] 1
Cable cross section [mm
2
] from 0,35 up to 1
Temperature range [°C] from -10 up to +45
Humidity range [%] 5-80 (no condensation)
Service life 100 000 switching operations
Ingress Protection Rating IP 30
Weight [g] 138
V95EN-02.indd 1 21.09.2015 12:56:32
WIRING DIAGRAM
WARNING!
All the operations with the products are allowed after power supply cutoff.
All mounting, addition, modification and maintenance operation for electric
equipment must be performed by qualified electricians with a work permit for electric
operations.
Connect the speed controller to ventilation units and domestic fans in compliance
with the wiring diagram below.
OUTOUT OUTOUT IN
LL1L2L3L4
230 V, 50/60 Hz
L
L
Speed controller wiring diagram
Speed controller operation
WARRANTY
Warranty period is 12 months since the sales date.
The Supplier bears no responsibility for any damages of the product incurred by violation of the transportation rules, product misuse,
unauthorized modification or repair.
is duly recognized as serviceable.
Approval mark Date of manufacture _____________________________________________
Sold by
name and stamp of the trade company _________________________________________________________________
_________________________________________________________________________________________________________________
Date of sale ________________________________
SENSOR SPEED CONTROLLER SRS1
V95EN-02
Operation Key
When connected to power mains the button has blue soft light
To turn ventilation equipment on press the button
To turn ventilation equipment o press the button
To decrease ventilation equipment speed press the button
To increase ventilation equipment speed press the button
Minimum speed setting:
1. Press and hold the button for about 5 seconds until the indicator shows
about 50 % of the operating speed range (that helps distinguish the setup
mode from the operating mode). The ventilation equipment will operate with
maximum speed.
2. Set minimum speed:
To set speed up press the button
To set speed down press the button
The set speed level is displayed on the LED indicator
To save set point press the button
To turn fan on and to activate its operation in set mode press the button
The minimum speed set point will be saved.
Every time you enter the set up mode the previous minimum fan speed is set as 100 % of the total capacity by default.
CONTROL
V95EN-02.indd 2 21.09.2015 12:56:33
  • Page 1 1
  • Page 2 2

Vents SRS-1 User manual

Vents
Brand
Vents
Model
SRS-1
Type
User manual

Vents SRS-1 is a sensor speed controller that allows you to control the speed of ventilation units and domestic fans. It is equipped with a sensitive sensor panel made of hardened glass, with the button and two buttons for speed control from minimum to maximum value. The speed controller has a power supply voltage of 230 V/50-60 Hz and a maximum load current of 1 A. It has a temperature range of -10 up to +45 °C and a humidity range of 5-80% (no condensation). The service life is 100,000 switching operations and the Ingress Protection Rating is IP 30. The weight is 138 g.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents