2. Midmark
  3. Classic Series
Classic Series

Midmark Classic Series Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Midmark Classic Series Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the intended use of the Mineral Deposit Reducer?
    Is there any specific local code requirement or restriction for installing the Mineral Deposit Reducer?
    What is the maximum line pressure that the Mineral Deposit Reducer can handle?
    Where should the Mineral Deposit Reducer be installed?
    What is the purpose of the quick connect fittings?
    How can I check for leaks in the system after installation?
    What is the warranty period for Midmark Air and Vacuum Accessories?
    What does the warranty cover?
    What does the warranty exclude?
    What is Midmark's obligation under the warranty?
© Midmark Corporation 2007
1
AA205400
OUT
To Vacuum System
IN
From Water Source
Quick Connect
Fitting
Mineral Deposit Reducer Installation
AVA82000
AMI61010 Rev. A
Components:
Filter Assy ....................................... 1
Bracket Kit ....................................... 1
Bowl Wrench .................................. 1
16’ Tubing ........................................ 1
Bushing (1/2” X 1/4”) ...................... 1
Quick Connect Fittings ................... 4
Intended Use:
To prevent scale and mineral deposits from
adhering to the wet-ring vacuum components.
Step 1: Turn off vacuum system.
Turn off the incoming water source.
Disconnect the water inlet hose from vacuum.
Step 3: Install quick connect fittings to “In” and “Out” ports.
Note: Direction of water flow through Mineral Deposit
Reducer must be maintained during installation.
Step 2: Install mounting bracket to wall.
Install Mineral Deposit Reducer to bracket.
Step 5: Turn water source on.
Turn vacuum system on.
Check for leaks in system.
Requirements / Restrictions:
Install Mineral Deposit Reducer according to local codes.
Protect from freezing.
Do NOT Install: • On line pressures above 100 PSI.
• Near direct sunlight or heat producing equipment.
Step 4: Cut tubing to size for incoming and outgoing water connections.
Install incoming tubing from water source to “In” port.
Install outgoing tubing from “Out” port to vacuum inlet connection.
Note: Bushing is provided for water source connection if needed.
Style A
2
© Midmark Corporation 2007
LIMITED WARRANTY
SCOPE OF WARRANTY
Midmark Corporation (“Midmark”) warrants to the original purchaser its Air and Vacuum accessories (except for components not warranted under “Exclusions”)
manufactured by Midmark to be free from defects in material and workmanship under normal use and service. Midmark’s obligation under this warranty is limited to the
repair or replacement, at Midmark’s option, of the parts or the accessories the defects of which are reported to Midmark within the applicable warranty period and
which, upon examination by Midmark, prove to be defective.
APPLICABLE WARRANTY PERIOD
The applicable warranty period, measured from the date of installation for the original user, shall be:
• Midmark Air and Vacuum Accessories: 90 Days
EXCLUSIONS
This warranty does not cover and Midmark shall not be liable for the following: (1) repairs and replacements because of misuse, abuse, negligence, alteration,
accident, freight damage, or tampering; (2) products which are not installed, used, and properly cleaned as required in the Midmark “Installation” manual and/or
Maintenance” guide for this applicable product; (3) products considered to be of a consumable nature; (4) accessories or parts not manufactured by Midmark; (5)
charges by anyone for adjustments, repairs, replacement parts, installation, or other work performed upon or in connection with such products which is not expressly
authorized in writing in advance by Midmark.
EXCLUSIVE REMEDY
Midmark’s only obligation under this warranty is the repair or replacement of defective parts. Midmark shall not be liable for any direct, special, indirect, incidental,
exemplary, or consequential damages or delay, including, but not limited to, damages for loss of profits or loss of use.
NO AUTHORIZATION
No person or firm is authorized to create for Midmark any other obligation or liability in connection with the products.
THIS WARRANTY IS MIDMARK’S ONLY WARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. MIDMARK MAKES NO IMPLIED WARRANTIES OF
ANY KIND INCLUDING ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. THIS WARRANTY IS LIMITED TO THE REPAIR OR
REPLACEMENT OF DEFECTIVE PARTS.
Midmark Corporation
For contact information, go to:
www.midmark.com
/