On-Q IC5004WH Operating instructions

Brand: On-Q

Model: IC5004WH

Category: Door intercom systems

Type: Operating instructions

This manual is also suitable for

Selective Call Intercom Patio Unit

301 Fulling Mill Road, Suite G

Middletown, PA 17057

Phone (800) 321-2343 / Fax (717) 702-2546

www.onqlegrand.com

Page 1 of 3

INSTRUCTION/INSTALLATION SHEET

Selective Call Intercom Patio Unit

IS-0388 REV. A

1. Introduction

The On-Q /Legrand Selective Call Intercom Patio Unit, PN IC5004-XX

(see Figure 1), is weather resistant for outdoor use, and supports

responding to a selective call, initiating a page within the house, local

control of the mute and monitor functions and the ability to talk to a Door

Unit. A separate high quality speaker and microphone provide superior

sound quality. It is available in white (-WH), shiny brass (-SB), antique

brass (-AB), brushed stainless (-BS) and oil-rubbed bronze (-OB).

2. Description

The Patio Unit is a 2-gang product that mounts within an outdoor

weatherproof box (56” from the floor to the bottom of the box). There is

also a two-gang surface-mount box available (P/N IC5006-BK) for unique

or retrofit installation requirements.

3. Installation

Installation of the Selective Call Patio Unit is best accomplished at multiple times during new construction, at

“Rough-in” before the drywall is installed, and at “Trim-out” after the drywall is installed and painted.

A. “Rough-in” steps:

1. Run a Cat 5 cable from the Enclosure where the Selective Call Intercom Module will be installed to the

2 gang box at the Selective Call Patio Unit location.

NOTE: A single Patio Unit in a one Module system may be run up to 1000 feet from the Module to

support a remote application. All other Patio Units on the system must be within 330 feet (100 meters)

of the Distribution Module.

NOTE: It is important to keep all Category 5e cable runs, regardless of use, at least 12 inches away from

AC electrical cables. If it proves necessary to cross an existing AC cable, do so only at a 90 degree

angle.

B. “Trim-out” steps:

NOTE: All terminations can be correctly completed by following the T568A pin assignments. It is

important that you accurately terminate using T568A at all locations. All terminations of the Selective Call

Intercom System are RJ45 jacks. Refer to Figure 2 for correct T568A termination of RJ45 plugs.

Figure 1

RJ-45

1 – White/Green

2 – Green

3 – White Orange

4 – Blue

5 – White/Blue

6 – Orange

7 – White/Brown

8 – Brown

RJ-45

1 – White/Green

2 – Green

3 – White Orange

4 – Blue

5 – White/Blue

6 – Orange

7 – White/Brown

8 – Brown

Figure 2

301 Fulling Mill Road, Suite G

Middletown, PA 17057

Phone (800) 321-2343 / Fax (717) 702-2546

www.onqlegrand.com

Page 2 of 3

INSTRUCTION/INSTALLATION SHEET

Selective Call Intercom Patio Unit

IS-0388 REV. A

NOTE: Make sure that the included weather proofing gasket is placed as shown in Figure 3.

1. As shown in Figure 3, the first step to installing the

Selective Call Patio Unit is to place the included rear

gasket against the gang or back box, and secure the

gasket in place with the included mounting bracket.

NOTE: Insure that the mounting bracket is installed with

the center tab pointed up, as the Patio Unit will be

“hung” from this tab in a later step.

NOTE: There are slotted holes in the mounting bracket

to allow for leveling of the Patio Unit in case the gang or

back box was installed off level.

2. Use the four provided screws to attach the mounting

bracket to the gang or back box.

3. Pull the Cat 5 cable from the enclosure through the

mounting bracket and terminate the cable with an RJ45

plug and insert the plug into the RJ45 jack on the rear of

the Patio Unit (see Figure 4). Follow the T568A

standards described in Figure 2.

4. Hang the Patio Unit from the top tab on the mounting bracket

and use the provided 1/16” allen wrench to tighten the two set

screws at the bottom of the Patio Unit.

5. Terminate the other end of the Cat 5 cable, at the Selective Call

Intercom Module, with an RJ45 plug using the T568A wiring

standard.

6. Insert the RJ45 plug into any of the eight Room, Patio, or Door

Unit jacks on the Intercom Module, (labeled 1-8).

7. After all Units and Modules are connected, apply power to the

Selective Call Intercom Module and verify system functionality.

All Selective Call Room, Door and Patio Units will be discovered

and shown on each Room Unit LCD.

Figure 3

rear

gasket

center tab

mounting

bracket

set screws

RJ45

jack

Figure 4

front gasket

301 Fulling Mill Road, Suite G

Middletown, PA 17057

Phone (800) 321-2343 / Fax (717) 702-2546

www.onqlegrand.com

Page 3 of 3

INSTRUCTION/INSTALLATION SHEET

Selective Call Intercom Patio Unit

IS-0388 REV. A

4. Operation

Please refer to Figure 5 to familiarize yourself with the basic operation of the Selective Call Intercom Patio Unit.

Please refer to the Selective Call System Installation Manual (P/N 1308003) shipped with the Room Unit for

more detailed instructions on how to use any Selective Call Room Unit to configure and personalize the

Selective Call System. Refer to the Selective Call System User Manual (P/N 1308001) shipped with the

Selective Call Module to familiarize yourself with the operation of the Selective Call Intercom System.

By default, the Patio Unit will not respond to Page All commands or hear internally monitored rooms. These

settings can be changed to allow both actions by using any Room Unit to change the defaults.

Figure 5

talk: Depressing this button will allow you to

communicate with all other active units. Hold in the talk

button while speaking, and let it go when you are done.

Your voice will be heard on any active Room or other

enabled Patio Unit within the system. Patio Units cannot

initiate a selective call.

volume: There are two volume control buttons

labeled + and -. Pressing the volume + button will

increase the volume level. You can also hold in the

volume + or - button until you have reached the

desired volume level.

door: Depressing this button will allow you to communicate

with the last Door Unit that rang its door tone. Hold in the

door button while speaking and let it go when you are done.

SPEAKER

MICROPHONE

monitor: Press this button once to put the Unit in

MONITOR mode and the monitor button will change its

normal white backlit color to red. This means that all other

non-Muted and non-Monitored units (other than Doors) will

be able to monitor this unit. If someone wants to contact the

monitored Patio unit they must place a selective call to that

unit. If the Mute button is also pressed, the unit cannot be

contacted. Press the monitor button again to return the Unit

back to normal mode. While in MONITOR mode, the

microphone is constantly active, and any voice or noise

within the area will be heard by any monitoring station. Door

Units are excluded from being Monitoring Stations. Multiple

Units can be in MONITOR mode at the same time.

NOTE: When in MONITOR mode, a door bell button

push at a Door Unit will not result in a door chime ring

at the Patio Unit.

mute: Press this button once to put the Unit in MUTE mode

and the button will change its normal white backlit color to

red. Press the button again to return the Unit back to normal

mode. While in MUTE mode, both the speaker and

microphone of the unit will be inactive. MUTE mode is useful

for maintaining privacy in a particular living space.

On-Q IC5004WH Operating instructions

Brand: On-Q

Model: IC5004WH

Category: Door intercom systems

Type: Operating instructions

This manual is also suitable for

Selective Call Intercom Patio Unit

Download PDF

report

On-Q IC5004WH Operating instructions

This manual is also suitable for

On-Q IC5004WH Operating instructions

Related papers

Other documents