Legrand Selective Call Intercom Room Unit - IC5000-xx Installation guide

Brand: Legrand

Model: Selective Call Intercom Room Unit - IC5000-xx

Category: Door intercom systems

Type: Installation guide

Legrand Selective Call Intercom Room Unit - IC5000-xx

The Legrand Selective Call Intercom Room Unit lets you enjoy crystal clear audio communication with other rooms, compatible door and patio units, and answer the door - all from the comfort of your room. It features an intuitive, user-friendly color LCD display that allows for seamless operation, including features like talk, talk to door, monitor, mute, and many others.

Legrand Selective Call Intercom Room Unit - IC5000-xx

INSTRUCTION / INSTALLATION SHEET

Selective Call Intercom Room Unit

IS-0386 Rev. B

301Fulling Mill Road, Suite G

Middletown, PA 17057

Phone (800) 321-2343 / Fax (717) 702-2546

www.onqlegrand.com

1. Introduction

The Legrand Selective Call Intercom Room Unit, PN IC5000-XX

(see Figure 1), is a critical component of the On-Q Selective

Call Intercom System. Using the intuitive Graphical User

Interface (GUI) provided via the color Liquid Crystal Display

(LCD), it provides both basic intercom communications

functions such as talk, talk to door, monitor, mute, and

advanced functions such as dynamic sorting of users or

monitoring multiple rooms at the same time. The Room Unit

GUI provides the only means to custom configure, or

personalize, the On-Q SCI Intercom System. The Room Unit is

available in white (-WH), light almond (-LA), gloss black (-GB)

and titanium (-TI).

2. Description

The Selective Call Room Unit is a two-gang decorator-style

product that connects to the Selective Call Distribution Module in

the enclosure via a single Cat 5e cable, up to 330’ in length.

3. Installation

Installation of the Selective Call Room Unit is best accomplished

at multiple times during new construction, at “Rough-in” before

the drywall is installed, and at “Trim-out” after the drywall is

installed and painted.

A. “Rough-in” steps:

To provide optimal display quality of the LCD on the Room

Unit, the two gang box that it is mounted in should be

located for eye level operation (see Figure 2). The bottom

of the two gang box should be approximately 56” from the

floor.

1. Run a Cat 5 cable from the Enclosure where the

Selective Call Intercom Distribution Module will be

installed to the 2 gang deep electrical box at the Room

Unit location.

NOTE: It is important to keep all Category 5e cable

runs, regardless of use, at least 12 inches away from

AC electrical cables. If it proves necessary to cross an

existing AC cable, do so only at a 90 degree angle.

Figure 1

Figure 2

INSTRUCTION / INSTALLATION SHEET

Selective Call Intercom Room Unit

IS-0386 Rev. B

301Fulling Mill Road, Suite G

Middletown, PA 17057

Phone (800) 321-2343 / Fax (717) 702-2546

www.onqlegrand.com

B. “Trim-out” steps:

NOTE: All terminations can be correctly completed by following the T568A pin assignments. It is

important that you accurately terminate using T568A at all locations. The Selective Call Intercom

System uses RJ45 plugs for all terminations on the Modules, the Room Units, the Door Units and

Patio Units. Refer to Figure 3 for correct T568A termination for RJ45 plugs.

1. As shown in Figure 4, label and terminate an RJ45 plug on the Cat 5 cable from the Selective Call

Intercom Module and attach it to the RJ45 jack on the rear of the Room Unit. Follow the T568A standards

described in Figure 3.

2. Insert the Selective Call Room Unit in position and the Cat 5 cable into the 2 gang box and secure the

unit to the box using the 4 included panhead screws. If using the included screwless wallplate option,

install mounting plate to Room Unit using 4 flathead screws and snap on the wall plate cover.

3. Terminate the other end of the Cat 5 cable, at the Selective Call Intercom Module, with an RJ45 plug

using the T568A wiring standard.

4. Insert the RJ45 plug into any of the eight ROOM UNIT jacks on the Selective Call Intercom Module in

the enclosure.

5. After all Units and Modules are connected, apply power to the Selective Call Intercom Module and

verify system functionality. All Selective Call Room, Door and Patio Units will be discovered and

shown on each Room Unit LCD.

RJ-45

1 – White/Green

2 – Green

3 – White Orange

4 – Blue

5 – White/Blue

6 – Orange

7 – White/Brown

8 – Brown

RJ-45

1 – White/Green

2 – Green

3 – White Orange

4 – Blue

5 – White/Blue

6 – Orange

7 – White/Brown

8 – Brown

Figure 4

Figure 3

RJ45 jack

Mounting Box screw

location (4 places)

Wall Plate Mounting

Plate screw location

(4 places)

INSTRUCTION / INSTALLATION SHEET

Selective Call Intercom Room Unit

IS-0386 Rev. B

301Fulling Mill Road, Suite G

Middletown, PA 17057

Phone (800) 321-2343 / Fax (717) 702-2546

www.onqlegrand.com

4. Operation

Please refer to the Selective Call System Installation Manual (P/N 1308003) shipped with the SCI Module for

more detailed instructions on how to use any Selective Call Room Unit to configure and personalize the

Selective Call System.

Figure 5

talk/select: Depressing this button will allow you to

communicate with any active units selected on the LCD

Display. Hold in the talk/select button while speaking, and

let it go when you are done. Your voice will be heard on

the selected Unit, or any active Room or Patio Unit if All is

selected.

monitor: Press this button once to put the Unit in

MONITOR mode. The LCD will display a message stating

that “MONITOR is On” and the monitor button will change

its normal white backlit color to red. This means that all

other non-Monitored units will be able to listen to this unit.

While in MONITOR mode, the microphone is constantly

active, and any voice or noise within the room will be heard

by any monitoring station. Multiple Units can be in

MONITOR mode at the same time. If someone wants to

contact the monitored unit they must place a selective call

to that unit. Press the monitor button again to return the

Unit back to normal mode. The LCD will tell you “MONITOR

is Off”. If the mute button is also pressed, the LCD will

indicate that you are in MONITOR and MUTE mode and the

unit cannot be contacted.

NOTE: When in MONITOR mode, a door bell button

push at a Door Unit will not result in a door chime ring

at the Room Unit.

volume: There are two volume control buttons, labeled +

and -. When either button is pressed, the LCD display turns

into a horizontal volume bar graph. Pressing the volume up

button increases the volume (the bar graph moves to the

right). You can also hold in the volume up or down button

until you have reached the desired volume level. The LCD

changes back to its normal display after 2 seconds of

inactivit

mute: Press this button once to put the Unit in MUTE

mode. The LCD will display a message that you are in

MUTE mode and the button will change its normal white

backlit color to red. Press the button again to return the Unit

back to normal mode. The LCD will display a message that

MUTE is Off. While in MUTE mode, both the speaker and

microphone of the unit will be inactive. MUTE mode is useful

for maintaining privacy in a particular room.

LCD: This is the Liquid Crystal Display that is used to

customize, personalize and operate the Selective Call

Intercom System. It identifies which unit is calling you, and

gives you status of all the individual units. It also provides

pop-up messages to inform you of specific operational

parameters.

SPEAKER

MICROPHONE

Legrand Selective Call Intercom Room Unit - IC5000-xx Installation guide

Brand: Legrand

Model: Selective Call Intercom Room Unit - IC5000-xx

Category: Door intercom systems

Type: Installation guide

Legrand Selective Call Intercom Room Unit - IC5000-xx

Download PDF

report

Legrand Selective Call Intercom Room Unit - IC5000-xx Installation guide

Legrand Selective Call Intercom Room Unit - IC5000-xx Installation guide

Related papers

Other documents