Samsung HT-KS700 User manual

Instruction Manual

Digital Surround

AV Receiver System

HT-AS700

1

Safety Warnings

This symbol indicates that dangerous voltage which

can cause electric shock is present inside this unit.

This symbol alerts you to important operating and

maintenance instructions accompanying the unit.

WARNING: To reduce the risk of fire or electric shock, do not

expose this appliance to rain or moisture.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

Wiring the Main Power Supply Plug(UK Only)

IMPORTANT NOTICE

The main lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin

face of the plug and if it requires replacing, a fuse approved to BS1362 of the same rating must be used.

Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must be of the same

colour as the fuse fitted in the plug. Replacement covers are available from your dealer.

If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should

obtain a suitable safety approved extension lead or consult your dealer for assistance.

However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the

plug to a main socket as there is a risk of shock hazard from the bared flexible cord.

Never attempt to insert bare wires directly into a main socket. A plug and fuse must be used at all times.

IMPORTANT

The wires in the main lead are coloured in accordance with the following code:–

BLUE = NEUTRAL BROWN = LIVE

As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as

follows:–

The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK.

The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.

WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH

THE LETTER E OR BY THE EARTH SYMBOL , OR COLOURED GREEN OR GREEN

AND YELLOW.

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE REAR COVER. NO USER SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

CLASS 1 LASER PRODUCT

This Compact Disc player is classified

as a CLASS 1 LASER product.

CAUTION

2

Precautions

Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install

your player horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4inches). Make sure the

ventilation slots are not covered. Do not stack anything on top of the player. Do not place the player on amplifiers or other

equipment which may become hot. Before moving the player, ensure the disc tray is empty. This player is designed for

continuous use. Switching off the DVD player to the stand-by mode does not disconnect the electrical supply. In order to

disconnect the player completely from the power supply, remove the main plug from the wall outlet, especially when left unused

for a long period of time.

Protect the player from moisture(i.e. vases) , and excess

heat(e.g.fireplace) or equipment creating strong magnetic or

electric fields (i.e.speakers...). Disconnect the power cable from

the AC supply if the player malfunctions. Your player is not

intended for industrial use.

Use of this product is for personal use only.

Condensation may occur if your player or disc have been

stored in cold temperatures.

If transporting the player during the winter, wait approximately 2

hours until the unit has reached room temperature before using.

During thunderstorms, disconnect AC main plug from

the wall outlet.

Voltage peaks due to lightning could damage the unit.

Do not expose the unit to direct sunlight or other heat

sources.

This could lead to overheating and malfunction of the

unit.

The battery used with this product contain chemicals

that are harmful to the environment.

Do not dispose of batteries in the general household

trash.

PREPARATION

√√

Let's find out difference between general amplifier and AV receiver!

General Amplifier

2 channels (left speaker and right speaker)

Play back music mainly

No decoder

Not play back various kinds of sound formats

AV Receiver

Multiple Channel (5.1 channel by default)

Play back music and video sound realistically

Has decoder

Dolby Pro Logic ll x

Dolby Pro Logic ll x is a new type of multiple

channel audio signal decoding method that

improves upon existing Dolby Pro Logic.

DTS (Digital Theater Systems)

DTS play backs 5.1 channel sound of wide-range

by playing sound of DVD and CD disk as surround

sound system.

DTS 96/24

DTS is the surround format implementing 5.1

channel multi channel sounds of 96KHz/24bit

without losing the image quality of DVD. In addition,

it can reproduce the matrix 6.1 of DTS 96/24

decoder signal.

DTS-ES

DTS-ES is the surround format implementing

surround type of discrete 6.1 channel while

preserving upper compatibility in response to

existing DTS Digital Sound format.

It is the latest digital sound format maximizing the

space quality and 360 surround experience by

adding rear center channels.

DOLBY DIGITAL EX

It not only significantly enhances space expression

capability of surround channel but also easily

implements the sound localization at the rear

according to sound field reproduction at 6.1 channel

including rear center channel.

DTS

It reproduces the digital PCM or analog stereo

sound source in 6.1 channels using the high

precision digital matrix of DTS only.

It refers to home theater exclusive amplifier by amplifying the audio signal from DVD and CD player as a core element of

home theater.

√√

What is AV receiver?

Features

3

Play back various kinds of sound formats including Dolby

Digital and DTS

Many input/output connectors

No noise using digital signal type

This product is manufactured with technical cooperation with Digital

Theater Systems, Inc., is the registered trademark of Digital

Theater Systems.

Manufactured under license from Dolby Laboratories.

“Dolby”, “ProLogic” and double-D symbol are the trademark of Dolby Laboratories.

Confidential unpublished works

Contents

4

PREPARATION

Safety Warnings ..............................................................................................................1

Precautions......................................................................................................................2

Features ..........................................................................................................................3

Contents ..........................................................................................................................4

Description ......................................................................................................................5

CONNECTIONS

Connecting the Speakers ...............................................................................................9

Connecting External Components ..................................................................................11

Connecting External Component.....................................................................................13

Connecting the FM Antenna............................................................................................14

OPERATION

Before Using AV Receivera .............................................................................................15

Selecting External Component Input ...............................................................................16

Setting the Speakera .......................................................................................................17

Setting DRC (Dynamic Range Compression) .................................................................21

Test Tone ........................................................................................................................22

Setting Speaker Level .....................................................................................................25

Dolby Pro Logic ll x Mode................................................................................................27

Dolby Pro Logic ll x Effect................................................................................................29

NEO:6 Mode....................................................................................................................31

SFE Mode........................................................................................................................33

EX/ES Mode ....................................................................................................................35

Stereo Mode ....................................................................................................................37

RADIO OPERATION

Listening to Radio ...........................................................................................................39

Presetting Radio Stations ...............................................................................................40

About RDS Broadcating ..................................................................................................41

MISCELLANEOUS

Convenient Functions .....................................................................................................43

Operating TV with Remote Control..................................................................................45

Operating VCR (DVD) with Remote Control....................................................................47

Before Calling for Service................................................................................................49

Specifications ..................................................................................................................51

PREPARATION

Description

[

Front Panel

]

[

Display

]

POWER button EXTERNAL VIDEO

INPUT CONNECTOR

VOLUME CONTROL

REMOTE CONTROL Sensor EXTERNAL OPTICAL DIGITAL

AUDIO INPUT CONNECTOR

SELECTION button

TUNING ( ) button

POWER STANDBY Indicator

EXTERNAL AUDIO INPUT CONNECTOR

SURROUND button

HEADPHONE Jack INPUT button

5

S.W

SPEAKER INDICATOR

SUBWOOFER

LEVEL INDICATOR

DOLBY PRO LOGIC

IIX

INDICATOR

VARIOUS

FUNCTION

INDICATOR

RADIO BROADCASTING

RECEIVING INDICATOR

RADIO STEREO INDICATOR

ANALOG INDICATOR

RADIO FREQUENCY

INDICATOR

OPTICAL DIGITAL

INDICATOR

DTS ES 96/24

INDICATOR

LIVE SURROUND

INDICATOR

L.PCM INDICATOR

NEO:6

INDICATOR

DOLBY DIGITAL EX

INDICATOR

MPEG2

INDICATOR

COAXIAL DIGITAL INDICATOR

,

6

DVD VIDEO INPUT

CONNECTOR

COOLING PAN

SAT VIDEO INPUT

CONNECTOR

5.1 CH ANALOG

AUDIO CONNECTOR

VCR VIDEO INPUT CONNECTOR

AM ANTENNA

CONNECTOR

VCR VIDEO OUTPUT CONNECTOR

MONITOR VIDEO OUTPUT

CONNECTOR

FM ANTENNA

CONNECTOR

OPTICAL DIGITAL AUDIO OUTPUT

CONNECTOR

DVD OPTICAL DIGITAL AUDIO INPUT CONNECTOR

SAT OPTICAL DIGITAL AUDIO

INPUT CONNECTOR

CD COAXIAL DIGITAL

AUDIO INPUT

CONNECTOR

SAT S-VIDEO INPUT CONNECTOR

VCR S-VIDEO INPUT CONNECTOR

VCR S-VIDEO OUTPUT CONNECTOR

CENTER SPEAKER TERMINAL

FRONT SPEAKER TERMINAL

REAR SPEAKER TERMINAL

MONITOR S-VIDEO OUTPUT CONNECTOR

[

Rear Panel

]

Accessories

√√

œœ

USER’S GUIDE

CD AUDIO INPUT CONNECTOR

DVD AUDIO INPUT CONNECTOR

SAT AUDIO INPUT CONNECTOR

Remote Control

FM Antenna User’s Manual

Battery(AAA Size 1.5V) AM Antenna

VCR AUDIO INPUT CONNECTOR

VCR AUDIO OUTPUT CONNECTOR

SUBWOOFER OUTPUT CONNECTOR 1

SUBWOOFER OUTPUT CONNECTOR 2

DVD S-VIDEO

INPUT

CONNECTOR

PREPARATION

Description

VOLUME CONTROL button

MUTE button

MENU button

ANALOG/DIGITAL button

POWER button

SLEEP button

TUNER button

NEO : 6 button

EXTERNAL DEVICE PLAYBACK button

DISPLAY button

MODE button

Direct Function Select button

TV Indicator

VCR Indicator

AV RECEIVER Indicator

TV/VIDEO

,

FUNCTION button

DVD Indicator

MODE button

MO/ST button

SUBWOOFER button

SFE MODE button

EX/ES button

EFFECT button

STEREO button

MOVE/SELECT button

TUNER MEMORY button

TUNING/CHANNEL button

SPEAKER LEVEL button

TEST TONE button

SPEAKER SETUP button

SPEAKER DISTANCE button

RDS Selection button

[

Remote Control

]

7

Number(0~9) buttons

8

To open the remote control cover,

push the top of the cover, then slide

downward.

Insert Remote Batteries

The remote control can be used up to approximately 23

feet/7 meters in a straight line. It can also be operated at

a horizontal angle of up to 30° from the remote control

sensor.

Range of Operation of the Remote Control

Remove the battery

cover on the back of

the remote by

pressing down and

sliding the cover in

the direction of the

arrow.

1

Insert two 1.5V AAA

batteries, paying

attention to the correct

polarities (+ and –).

2

Replace the battery

cover.

3

Follow these precautions to avoid leaking or cracking batteries:

•

Place batteries in the remote control so they match the polarity:(+) to (+)and (–)to (–).

•

Use the correct type of batteries.Batteries that look similar may differ in voltage.

•

Always replace both batteries at the same time.

•

Do not expose batteries to heat or flame.

Caution !

PREPARATION

Connecting the Speakers

Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

•

Place the rear left and right speaker at the interval of front

left and right speaker.

•

If there isn't enough now, place rear speakers to face

down other.

•

Place the rear speakers about 70 cm to 1 m above your

ear, facing slightly downwards.

❈ Unlike the front and center speakers, the rear speakers

and used to mainly sound effects and sound will not

come from them all the time.

Rear Speakers

•

If you place 1 rear center speaker, place it so that it faces

forward from the back of listener.

•

Place the rear center speaker about 70 cm to 1 m above

rear speakers, facing slightly downwards.

Rear Center Speaker

SL SR

SB

•

Adjust the angle of front left and right speakers so

that it can form 30 degree to the left and right from

the listening position.

•

Place the speakers so that their tweeters will be at

the same height as your ear.

•

Align the front face of the front speakers with the

front face of the center speaker or place them

slightly in front of the center speaker.

Front Speakers

•

It is best to install center speaker at the same height as

the front speakers.

•

You can also place center speaker directly over or

under the TV.

Center Speaker

•

Place AV Receiver on the dedicated stand or chest of

living room or under the TV stand properly.

Position of AV Receiver

•

The position of the subwoofer is not so critical. Place it

anywhere you like.

•

Usually, it is placed by a corner near the front speakers.

Subwoofer

When you place the speaker on the wall, make sure

to fasten it tightly so that it may not fall off.

9

Caution!

10

CONNECTIONS

•

Never touch speaker terminals while

the power is on. Doing so could

result in electric shock.

•

Make sure the polarities (+ and -)

are correctly.

1

√ Connecting Front Speaker Wire

MAIN UNIT AV-R700

FRONT SPEAKER PSAF700E

CENTER SPEAKER PSAC700E

REAR SPEAKER PSAR700E

REAR CENTER SPEAKER PSAB700E

ACTIVE SUB WOOFER PSAW700E

SYSTEM MODEL NAME : HT-AS700

√ Connecting Center/Rear Speaker Wire

PASSIVE

SUBWOOFER

ACTIVE SUBWOOFER

(BUILT-IN POWER

AMPLIFIER)

PSAW700E

POWER

AMPLIFIER

FRONT (R)

PSAF700E

FRONT (L)

PSAF700E

REAR (R)

PSAR700E

REAR (L)

PSAR700E

MAIN UNIT

AV-R700

CENTER

PSAC700E

REAR CENTER

PSAB700E

Caution!

Turn and loosen the

speaker connector.

2

1

Press the tab of the

speaker connector.

2

Insert the black wire into the black(-)

terminal and the red wire into the

red(+) terminal.

3

Turn and fasten the

speaker connector.

Insert the black wire into the black(-)

terminal and the red wire into the

red(+) terminal.

Connecting External Components

DIGITAL

OUT

AUDIO

OUT

VIDEO

OUT

S-VIDEO

OUT

LR

AUDIO

IN

AUDIO

OUT

VIDEO

OUT IN

S-VIDEO

OUT IN

LRLR

S-VIDEO

IN

DVD Player

Video ProjectorVideo Player

•

Disconnect the power plug from the outlet if you do not use this unit for long period of time.

Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

Connecting Video Component

11

Caution!

VIDEO

IN

S-VIDEO

IN

DIGITAL

OUT

AUDIO

OUT

VIDEO

OUT

S-VIDEO

OUT

LR

DIGITAL

IN

SAT Player

TV MD Player

•

If the Audio Output connector of external

component is only 1, connect Audio Output

connector or external component to either of

Audio Input connector (right or left) of main unit.

•

Connect the red cable of audio cable to red

connector and white cable to white connector.

•

When you connect Video Input connector of

external component to Video Output connector

of main unit, connect Video Input connector of

external component either to Video Output

connector or S-Video Output connector.

12

CONNECTIONS

Connecting External Component

LR

DIGITAL

OUT

AUDIO

OUT

FRONT SURR.

SUB

WOOFER

L

R

L

R

CENTER

CD Player

DVD or 5.1 Channel Player

Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

Connecting Audio Component/ 5.1 Channel

13

14

1. Connect the FM antenna supplied to the FM

75ΩCOAXIAL terminal as a temporary mea-sure.

2. Slowly move the antenna wire around until you find

a location where reception is good, then fasten it to

a wall or other rigid surface.

1. Connect the AM loop antenna supplied to the AM

and terminals.

2. If reception is poor, connect an outdoor single vinyl-

covered wire to the AM ter-minal. (Keep the AM loop

antenna con-nected).

The cooling fan dissipates the heat generated inside the unit so that the unit can

be operated normally. The cooling fan is activated automatically to supply cool air

to the unit.

Please observe the following cautions for your safety.

•

Make sure the unit is well-ventilated. If the unit has poor ventilation, the temperature inside the

unit could rise and may damage it.

•

Do not obstruct the cooling fan or ventilation holes. (If the cooling fan or ventilation holes are

covered with a newspaper or cloth, heat may build up inside the unit and fire may result.)

Connecting the FM and AM

Antennas

FM antenna connection

If AM reception is poor, connect an

outdoor AM antenna(not supplied).

FM Antenna (supplied)

AM Loop Antenna

(supplied)

Snap the tabs on the loop into the

slots of the base to assemble the

AM loop antenna.

COOLING FAN

AM antenna connection

CONNECTIONS

Before Using AV Receiver

Turning On/Off

Functions of Dedicated Remote Control

Connect the power plug to the outlet.

1

Press the POWER ( ) button of the main unit.

•

This unit will be turned on or off.

2

MAIN UNIT

REMOTE CONTROL

Press MODE button.

•

Each time you press this button, it will select and blink TV indicator ➝ VCR indicator

➝DVD indicator ➝AV Receiver indicator in turn.

•

You can operate TV after TV indicator blinking.

You can operate VCR after VCR indicator blinking.

You can operate DVD after DVD indicator blinking.

You can operate AV Receiver after AV Receiver indicator blinking.

•

This unit will not turned on or off even if you press the POWER ( ) button of

remote controller while main unit is turned off.

•

When you turn off the power by pressing the POWER ( ) button of remote

control, this unit will be standby mode.To completely turn off the power, press the

POWER ( ) button of the main unit. Standby indicator will be turned off.

•

Basic operation of remote control is set up based on Samsung products.

Refer to page 45~48 for more details on operation method.

You can operate TV, VCR, DVD, AV Receiver with one remote control.

15

To set the menu function of external component

Press the MENU button.

•

Menu setup screen of TV, VCR and DVD Player will appear.

REMOTE CONTROL

Press the POWER ( ) button of the remote control while main unit is turned on.

•

This unit will be turned on or off.

You can listen ti sound in Analog 2 Channels or Dolby Digital 5.1 Channel using this unit.



16

Press the FUNCTION button.

•

When you select the audio external component (external component without

Video Output connector), the image of video external component (external

component with Video Output connector) used last will appear in the TV screen.

•

You can watch the image of video external component while listening to sound of

audio external component.

Selecting External Component Input

•

You can enjoy Dolby Digital effect only if you connect Audio Output connector of

external audio component to optical/coaxial digital Audio Input connector of main unit.

To Select the Function

To Select Analog/Digital Input

REMOTE CONTROL

•

You can directly select 5.1CH, VCR, DVD, CD, SAT, or AUX.

•

For DVD, SAT, AUX Function

ANALOG and OPTICAL (1, 2, 3) will be selected repetitively.

•

For CD Function

ANALOG and COAXIAL will be selected repetitively.

MAIN UNIT

REMOTE CONTROL

Press INPUT button.

•

Each time you press the this button, 5.1CH MULTI CH ➝CD ➝DVD ➝ SAT ➝VCR ➝AUX

➝FM ➝AM will be selected in turn.

Press the ANALOG/DIGITAL button.

•

You can operate this function only with remote controller.

•

This function will be selected in analogue only for VCR function, and will not work for 5.1CH MULTI CH function.

Caution!

Method 1

Press DIRECT FUNCTION Select button.

Method 2

Press the FUNCTION button.

•

Each time you press the this button, 5.1CH MULTI CH ➝CD ➝DVD ➝ SAT ➝VCR ➝

AUX ➝FM ➝AM will be selected in turn.

OPERATION

Setting the Speaker

Before moving or installing the product, be sure to turn off the power and disconnect the power cord.Signal outputs

and frequency response from the speaker will automatically be adjusted according to your speaker configuration

and whether certain speakers are used or not.

Press SPK SEL. button to select the speaker you want.

•

Each time you press this button, F.SPK ➝ C.SPK ➝S.SPK ➝SB SPK ➝

SW SPK ➝CROVR ➝SPK MODE OFF will be selected in turn.

Press …† button to set the speaker as you want.

Repeat the steps 1 and 2 to set the speaker.

To Exit Setup Mode

•

Wait for about 5 seconds or press the SPK SEL. button of the remote control to

select SPK MODE OFF.

To Use SUBWOOFER button of Remote Control

Press SUBWOOFER button.

•

Each time you press this button, SW SPK : YES, SW SPK : NO will be selected in turn.

•

If you play in 2 Channel Stereo, select 'YES' to use Subwoofer and 'NO' not to use.

√

•

If F.SPK is set to ‘SMALL’, SW SPK is fixed to ‘YES’.

•

If S.SPK is set to ‘NONE’, SB SPK is fixed to ‘NONE’.

•

You cannot use Speaker Setup Mode in 5.1CH MULTI CH function.

17

1

2

3

REMOTE CONTROL

Caution!

Press and hold SURROUND button for about 5 seconds.

•

“SETUP MODE” appears on the display and enters into Setup Mode.

Press INPUT button one time.

•

“SPEAKER SETUP” appears in the display.

Press SURROUND button to select the speaker you want.

Each time you press this button, F.SPK ➝ C.SPK ➝S.SPK ➝SB

SPK ➝SW SPK ➝CROVR will be selected in turn.

Press SELECT ( ) button to set the speaker as you want.

Repeat the steps 3 and 4 to set the speaker.

To Exit Setup Mode

•

Wait for about 5 seconds or turn the VOLUME CONTROL of the main unit.

“SETUP MODE OFF” appears on the display and exits Setup Mode.

•

LARGE : Select when you use large speaker. You can listen to full

ranges of sound from bass to treble.

•

SMALL : Select this when you use small speaker. Bass below

100ß‘ will not be output from the whole speakers but only

from subwoofer.

•

NONE : Select this when you use no speaker.

•

YES : Select this when you use Subwoofer Speaker if you play

back in 2 Channel Stereo.

•

NO : Select when you do not use Subwoofer Speaker if you play

back in 2 Channel Stereo.

•

CROVR: Select the crossover frequency depending on the size of

speaker connected when you use subwoofer. Select 40Hz

if cone paper speaker is 16cm, select 60Hz for 14cm,

80Hz for 12cm, 100Hz for 10cm, 12Hz for 8cm ,150Hz for

6cm and 200Hz for 4cm.

18

•

F.SPK (Front) : LARGE, SMALL

•

C.SPK (Center) : LARGE, SMALL, NONE

•

S.SPK (Rear) : LARGE, SMALL, NONE

•

SB SPK (Rear Center) : LARGE, SMALL, NONE

•

SW SPK (Subwoofer) : YES, NO

•

CROVR (Crossover Frequency): 40, 60, 80, 100, 120, 150,200Hz

Setting the Speaker

MAIN UNIT

1

2

4

5

3

,

OPERATION

Setting the Speaker

Press the SPEAKER DISTANCE button to select the

speaker you want.

•

Each time you press this button, F.L ➝ CEN ➝F.R ➝S.R ➝ S.B ➝S.L ➝

S.W ➝DISTANCE OFF will be selected in turn.

Press …† button to set the speaker distance.

•

For F.L, CEN, F.R, S.W Speaker, you can set the distance from the speaker to

listening position between 0.0~1.5m at the interval of 0.3m.

•

For S. R, S.B, S.L Speaker, you can set the distance from the speaker to

listening position between 0.0~4.5m at the interval of 0.3m.

Repeat the steps 1 and 2 to set the speaker distance.

To Exit Setup Mode

•

Wait for about 5 seconds or press the SPEAKER DISTANCE button of remote control

to select DISTANCE OFF.

19

√

•

If the listening position is beyond the range of speaker

distance setup when you place the speaker, set the

speaker distance to the maximum.

REMOTE CONTROL

1

2

3

Page is loading ...

Samsung HT-KS700 User manual

This manual is also suitable for

Samsung HT-KS700 User manual

Related papers

Other documents