HP D5259A - Pavilion M70 - 17" CRT Display User manual

Brand: HP

Model: D5259A - Pavilion M70 - 17" CRT Display

Category: TVs & monitors

Type: User manual

This manual is also suitable for

User’s Guide

Color Monitor Series

v72

HP, Hewlett-Packard, and the Hewlett-Packard logo are trademarks of

Hewlett-Packard Company in the U.S. and other countries/regions.

Microsoft, MS-DOS, Windows, and Windows NT are trademarks of

Microsoft Corporation in the U.S. and other countries/regions.

Intel, Pentium, Intel Inside, and Celeron are trademarks of Intel

Corporation in the U.S. and other countries/regions.

Adobe, Acrobat, and Acrobat Reader are trademarks or registered

trademarks of Adobe Systems Incorporated.

All other product names mentioned herein may be trademarks of their

respective companies.

Hewlett-Packard Company shall not be liable for technical or

editorial errors or omissions contained herein or for incidental

or consequential damages in connection with the furnishing,

performance, or use of this material. The information in this document

is provided “as is” without warranty of any kind, including, but

not limited to, the implied warranties of merchantability and fitness

for a particular purpose, and is subject to change without notice.

The warranties for HP products are set forth in the express limited

warranty statements accompanying such products. Nothing herein

should be construed as constituting an additional warranty.

THE WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT

TO THE EXTENT LAWFULLY PERMITTED, DO NOT EXCLUDE,

RESTRICT OR MODIFY AND ARE IN ADDITION TO ANY

MANDATORY STATUATORY RIGHTS APPLICABLE TO THE SALE

OF THIS PRODUCT OR SERVICE TO YOU.

This document contains proprietary information that is protected

by copyright. No part of this document may be photocopied,

reproduced, or translated to another language without the prior

written consent of Hewlett-Packard Company.

WARNING: Text set off in this manner indicates that failure to

follow directions could result in bodily harm or loss of life.

CAUTION: Text set off in this manner indicates that failure to follow

directions could result in damage to equipment or loss of

information.

User’s Guide iii

Contents

1 Introduction

Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1

2 Safety and Maintenance Guidelines

Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . 2–1

Power Requirements . . . . . . . . . . . . . . . . . . . 2–1

Important Safety Information. . . . . . . . . . . . . . 2–1

Maintenance Guidelines . . . . . . . . . . . . . . . . . . . 2–2

Removing the Monitor Base . . . . . . . . . . . . . . 2–4

3 Installation

Monitor Base Installation . . . . . . . . . . . . . . . . . . . 3–1

Monitor Installation . . . . . . . . . . . . . . . . . . . . . . . 3–2

4Operation

Information Files. . . . . . . . . . . . . . . . . . . . . . . . . 4–1

Installing Drivers . . . . . . . . . . . . . . . . . . . . . . 4–2

Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . 4–5

On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . 4–6

On-Screen Display Functions . . . . . . . . . . . . . 4–7

Monitor Messages . . . . . . . . . . . . . . . . . . . . . . . 4–9

No Signal Message. . . . . . . . . . . . . . . . . . . . 4–9

Out of Frequency Range Message. . . . . . . . . 4–10

Using the Energy Saver Mode . . . . . . . . . . . . . . 4–11

iv User’s Guide

A Troubleshooting

Solving Common Problems . . . . . . . . . . . . . . . . . A–1

Using the World Wide Web . . . . . . . . . . . . . . . . A–4

Preparing to Call Technical Support . . . . . . . . . . . A–4

B Technical Specifications

v72 Series Monitor . . . . . . . . . . . . . . . . . . . . . . . B–1

C Agency Regulatory Notices

Federal Communications Commission Notice. . . . . C–1

Modifications . . . . . . . . . . . . . . . . . . . . . . . . C–1

Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . C–2

Declaration of Conformity for Products Marked

with FCC Logo, United States Only. . . . . . . . . . . . C–2

Canadian Notice . . . . . . . . . . . . . . . . . . . . . C–2

Avis Canadien . . . . . . . . . . . . . . . . . . . . . . . C–3

European Notice. . . . . . . . . . . . . . . . . . . . . . C–3

Japanese Notice . . . . . . . . . . . . . . . . . . . . . . C–3

Korean Notice . . . . . . . . . . . . . . . . . . . . . . . C–3

EPA Energy Star Compliance . . . . . . . . . . . . . C–4

Power Cord Set Requirements . . . . . . . . . . . . . . . C–4

D TCO‘99 Requirements

Environmental Requirements. . . . . . . . . . . . . . . . . D–3

Flame Retardants. . . . . . . . . . . . . . . . . . . . . . D–3

Cadmium . . . . . . . . . . . . . . . . . . . . . . . . . . . D–4

Mercury . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–4

CFCs (Freons) . . . . . . . . . . . . . . . . . . . . . . . . D–4

Lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–5

User’s Guide 1–1

Introduction

Your microprocessor-based, digitally controlled color monitor is a

high-performance and easy-to-use product. It employs the latest

on-screen menu technology.

Kit Contents

The monitor kit contains:

■ CRT monitor

■ Monitor Base (pre-installed on select models)

■ AC power cord (select models)

■ Documentation kit

Introduction

1–2 User’s Guide

User’s Guide 2–1

Safety and Maintenance

Guidelines

Safety Guidelines

Power Requirements

Refer to the “Power Cord Set Requirements” on page C–4 for

information on the correct power cord set for this device.

Important Safety Information

WARNING: To reduce the risk of electric shock or damage to your

equipment, do not disable the power cord grounding feature. This

equipment is designed to be connected to a grounded (earthed)

power outlet that is easily accessible to the operator. The grounding

plug is an important safety feature.

WARNING: For your safety, be sure that the power outlet you plug

the power cord into is easily accessible and located as close to the

equipment as possible. When you need to disconnect the power to

the equipment, unplug the power cord from the power outlet by

grasping the plug firmly. Never pull on the cord.

CAUTION: For the protection of your monitor, as well as your

computer, connect all power cords for your computer and its

peripheral devices (such as a monitor, printer, scanner) to some form

of surge protection device such as a power strip or Uninterruptible

Power Supply (UPS). Not all power strips provide surge protection;

the power strips must be specifically labeled as having this ability.

Use a power strip whose manufacturer offers a Damage

Replacement Policy so you can replace your equipment if surge

protection fails.

Safety and Maintenance Guidelines

2–2 User’s Guide

Maintenance Guidelines

To enhance the performance and extend the life of your monitor,

follow these guidelines:

■ Do not open your monitor cabinet or attempt to service this

product yourself. If your monitor is not operating properly, or

has been dropped or damaged, first unplug from power outlet,

then contact your Hewlett-Packard authorized dealer, reseller,

or service provider.

■ Adjust only those controls that are discussed in the operating

instructions.

■ Place your monitor at least 3 inches (76 mm) away from walls

or other enclosures.

■ Use only a power source and connection appropriate for this

monitor, as indicated on the label/back plate of the monitor.

■ Be sure the total ampere rating of the products connected to

the outlet does not exceed the current rating of the electrical

outlet, and the total ampere rating of the products connected

to the cord does not exceed the rating of the cord. Look on the

power label to determine the ampere rating (AMPS or A) for

each device.

■ Install your monitor near an outlet that you can easily reach.

Disconnect the monitor by grasping the plug firmly and pulling

it from the outlet. Never disconnect the monitor by pulling

the cord.

■ Turn your monitor off when not in use. You can substantially

increase the life of your monitor by using a screen saver

program and turning off the monitor when not in use.

■ Unplug your monitor from the wall outlet before cleaning. Do

not use liquid cleaners or aerosol cleaners. Use a damp cloth

for cleaning. If the screen requires additional cleaning, use an

antistatic CRT screen cleaner.

CAUTION: Do not use benzene, thinner, ammonia, or any other

volatile substances to clean your monitor or the screen. These

chemicals may damage the cabinet finish as well as the screen.

Safety and Maintenance Guidelines

User’s Guide 2–3

■ Slots and openings in the cabinet are provided for ventilation.

These openings must not be blocked or covered. Never push

objects of any kind into cabinet slots or other openings.

■ Do not place plants on top of your monitor. Water or dirt from

the plant may get into the vents.

■ Do not drop your monitor or place it on an unstable surface.

■ Do not allow anything to rest on the power cord. Do not walk

on the cord.

■ Keep your monitor in a well-ventilated area, away from

excessive light, heat or moisture. Keep your monitor away

from high-capacity transformers, electric motors, and other

devices with strong magnetic fields.

■ In a two-monitor system, place your monitors as far apart from

one another as possible to lessen interference between them.

■ Do not place the monitor face down. Damage could result to

the front panel controls or the monitor screen.

Safety and Maintenance Guidelines

2–4 User’s Guide

Removing the Monitor Base

In the event that you need to disassemble the base from the

monitor, follow these instructions:

1. If you must remove the base attachment, release the catch and

slide the base toward the back of your monitor.

2. Lift the base up and away from your monitor.

User’s Guide 3–1

Installation

Monitor Base Installation

On some monitors, the base must be attached prior to monitor

installation. If you need to attach the base, follow these steps:

1. Align the hooks on the base with the sockets on the bottom of

the monitor and attach the base.

Installation

3–2 User’s Guide

2. Push the base toward the front of the monitor until it stops.

Monitor Installation

Before installing your monitor, place it in a convenient,

well-ventilated location near your computer.

1. Turn off the power to your computer and other peripheral

devices.

2. Connect the video cable (blue connector) 1 from the back of

the monitor to the blue 15-pin connector on the back of the

computer. Tighten the cable screws to secure the cable to the

connector.

CAUTION: To avoid damaging the video cable, ensure that the

cable aligns with the 15-pin connector. Do not force the cable onto

the connector.

Installation

User’s Guide 3–3

3. Connect the power cord 2 to the back of the monitor, then

connect the power cord to a power outlet.

4. Power on your computer and monitor.

If your monitor fails to function properly, refer to Appendix A,

“Troubleshooting.”

5. If necessary, adjust the front panel monitor controls according

to your personal preference. See “Front Panel Controls” on

page 4–5 for detailed information.

Your monitor installation is now complete.

Installation

3–4 User’s Guide

User’s Guide 4–1

Operation

Information Files

The CD-ROM included with this monitor contains two data files

that must be installed onto your computer: An .INF file and an

.ICM file.

The .INF file designates software and defines monitor resources

used by Microsoft Windows to ensure monitor compatibility with

the graphics adapter in your computer.

The .ICM file provides color matching consistency between your

monitor screen and your printer. Once installed, this file is

activated by graphics programs that have this color-matching

feature.

To install these files on your computer:

1. Insert the CD-ROM disc that came with the monitor in your

computer’s optical drive.

2. Perform the steps to install the drivers. See “Installing Drivers”

on page 4–2 and choose the steps for your operating system.

3. To get the latest .INF and .ICM files, download them from the

HP Web site. Access http://www.hp.com and follow the links

to the Support page for monitors to download the appropriate

files.

Operation

4–2 User’s Guide

Installing Drivers

The HP monitor comes with driver software allowing you to take

advantage of the Plug and Play feature of the Windows Me,

Windows 2000, or Windows XP operating system. This software

enables the computer to communicate with the monitor and use all

the monitor features.

HP computers may come with the Plug and Play drivers

pre-installed. If you have an older computer, these drivers may not

be pre-installed and you may need to install the drivers from the

CD-ROM disc that came with the monitor.

If the installation procedure for the operating system is different, or

if you need more detailed installation information, please refer to

the Microsoft Windows information that came with the computer.

Windows 2000 users

The procedure for installing the driver for your operating system

may vary.

To install the driver for the v72 monitor:

1. Click Start, select Settings, and then click Control Panel.

2. Double-click Display.

3. Click the Settings tab.

4. Click Advanced Properties or Advanced, and select the

Monitor tab.

5. Click Properties.

6. Click the Driver tab.

7. Click Update Driver and click Next.

8. Select the recommended option, and then click Next.

9. Select the Specify a Location box.

10. Find and open the hp_v72.inf file on the CD-ROM disc in the

Drivers directory, and click OK.

11. Click Next to install the monitor driver.

Operation

User’s Guide 4–3

Windows Me users

The procedure for installing the driver for your operating system

may vary.

To install the driver for the v72 monitor:

1. Click Start, select Settings, and then click Control Panel.

2. Double-click Display.

3. Click the Settings tab.

4. Click the Advanced button.

5. Select the Monitor tab.

6. Click the Change button.

7. Select the Specify the location of the driver box, and

then click Next.

8. Find and open the hp_v72.inf file on the CD-ROM disc in the

Drivers directory, and click OK.

9. Click Next to install the monitor driver.

Windows XP users

The procedure for installing the driver for your operating system

may vary.

To install the driver for the v72 monitor:

1. Click Start.

2. Click Control Panel.

3. Click Appearance and Themes.

4. Click Display.

5. Select the Settings tab.

6. Click the Advanced button.

7. Select the Monitor tab.

Operation

4–4 User’s Guide

8. Click Properties.

9. Select the Driver tab.

10. Click Update Driver.

11. Select the Install from a list or specific location box,

and then click Next.

12. Select the Don’t search box, and then click Next.

13. Click Have Disk.

14. Click Browse.

15. Find and open the hp_v72.inf file on the CD-ROM disc in the

Drivers directory, and click OK.

16. Click Next to install the monitor driver.

If the installation procedure of the monitor driver for the Windows

2000, Windows Me, or Windows XP operating system is different,

or if you need more detailed installation information, refer to the

Microsoft Windows information that came with the PC.

Operation

User’s Guide 4–5

Front Panel Controls

Item Icon Name Function

Select Launches on-screen displays,

selects functions and

adjustments, and exits menus

and On-Screen Display.

Left Adjustment Moves backward through menu

options or decreases

adjustment levels.

Right Adjustment Moves forward through menu

options or increases adjustment

levels.

Power/LED Controls power to the monitor.

The LED on the power button

indicates the state of the

monitor.

Operation

4–6 User’s Guide

On-Screen Display

The On-Screen Display (OSD) adjusts the screen image based on

your viewing preferences. To access the OSD, do the following:

1. If the monitor is not already on, press the Power button to turn

on the monitor.

2. Press the Select button to display the On-Screen Display menu.

A screen similar to this one appears. For a description of the

icons that appear on the screen, see “On-Screen Display

Functions” on page 4–7.

3. To move to a function, press the Right-Adjustment or

Left-Adjustment button on the front panel of your monitor until

the function is highlighted.

4. Press the Select button on the monitor choose the function.

5. The adjustment window displays. Press the Right-Adjustment or

Left-Adjustment buttons to increase (Right) or decrease (Left) the

level of adjustment.

6. Press Select to save the new adjustment.

7. To exit the On-Screen Display, select the Exit icon and press

the Select button once.

Page is loading ...

HP D5259A - Pavilion M70 - 17" CRT Display User manual

Brand: HP

Model: D5259A - Pavilion M70 - 17" CRT Display

Category: TVs & monitors

Type: User manual

This manual is also suitable for

Download PDF

report

HP D5259A - Pavilion M70 - 17" CRT Display User manual

This manual is also suitable for

HP D5259A - Pavilion M70 - 17" CRT Display User manual

Related papers

Other documents