Brother BM2800 User manual

Page is loading ...

———————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—————

1

IMPORTANT SAFETY

INSTRUCTIONS

Please read these safety instructions

before attempting to use the machine.

DANGER - To reduce the

risk of electric shock:

1 Always unplug the machine from

the electrical outlet immediately after

using, when cleaning, when making

any user servicing adjustments

mentioned in this manual, or if you are

leaving the machine unattended.

WARNING - To reduce the

risk of burns, fire, electric shock, or

injury to persons.

2 Always unplug the machine from

the electrical outlet when making any

adjustments mentioned in the

instruction manual:

• To unplug the machine, switch the

machine to the symbol “O” position

to turn it off, then grasp the plug and

pull it out of the electrical outlet. Do

not pull on the cord.

• Plug the machine directly into the

electrical outlet. Do not use an

extension cord.

• Always unplug your machine if the

power is cut.

3 Never operate this machine if it has

a damaged cord or plug, if it is not

working properly, if it has been

dropped or damaged, or water is spilled

on the unit. Return the machine to the

nearest authorized dealer or service

center for examination, repair,

electrical or mechanical adjustment.

• While the machine is stored or in use

if you notice anything unusual, such

as an odor, heat, discoloration or

deformation, stop using the machine

and immediately unplug the power

cord.

• When transporting the machine, be

sure to carry it by its handle. Lifting

the machine by any other part may

damage the machine or result in the

machine falling, which could cause

injuries.

• When lifting the machine, be careful

not to make any sudden or careless

movements, otherwise you may

injure your back or knees.

4 Always keep your work area clear:

• Never operate the machine with any

air openings blocked. Keep

ventilation openings of the machine

and foot control free from the build

up of lint, dust, and loose cloth.

• Do not store objects on the foot

controller.

• Do not use extension cords. Plug the

machine directly into the electrical

outlet.

• Never drop or insert any object into

any opening.

• Do not operate where aerosol (spray)

products are being used or where

oxygen is being administered.

• Do not use the machine near a heat

source, such as a stove or iron;

otherwise, the machine, power cord

or garment being sewn may ignite,

resulting in fire or an electric shock.

• Do not place this machine on an

unstable surface, such as an unsteady

or slanted table, otherwise the

machine may fall, resulting in

injuries.

5 Special care is required when

sewing:

• Always pay close attention to the

needle. Do not use bent or damaged

needles.

2

—————

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—

——————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

• Keep fingers away from all moving

parts. Special care is required around

the machine needle.

• Switch the machine to the symbol

“O” position to turn it off when

making any adjustments in the needle

area.

• Do not use a damaged or incorrect

needle plate, as it could cause the

needle to break.

• Do not push or pull the fabric when

sewing, and follow careful instruction

when freehand stitching so that you

do not deflect the needle and cause it

to break.

6 This machine is not a toy:

• Your close attention is necessary

when the machine is used by or near

children.

• The plastic bag that this machine was

supplied in should be kept out of the

reach of children or disposed of.

Never allow children to play with the

bag due to the danger of suffocation.

• Do not use outdoors.

7 For a longer service life:

• When storing this machine, avoid

direct sunlight and high humidity

locations. Do not use or store the

machine near a space heater, iron,

halogen lamp, or other hot objects.

• Use only neutral soaps or detergents

to clean the case. Benzene, thinner,

and scouring powders can damage

the case and machine, and should

never be used.

• Always consult the operation manual

when replacing or installing any

assemblies, the presser feet, needle,

or other parts to assure correct

installation.

8 For repair or adjustment:

• If the Light unit (light-emitting diode)

is damaged, it must be replaced by

authorized dealer.

• In the event a malfunction occurs or

adjustment is required, first follow the

troubleshooting table in the back of

the operation manual to inspect and

adjust the machine yourself. If the

problem persists, please consult your

local authorized Brother dealer.

Use this machine only for its intended

use as described in this manual.

Use accessories recommended by the

manufacturer as contained in this

manual.

The contents of this manual and

specifications of this product are

subject to change without notice.

For additional product information,

visit our web site at www.brother.com

SAVE THESE

INSTRUCTIONS

This machine is intended

for household use.

This appliance is not intended for use by

persons (including children) with

reduced physical, sensory or mental

capabilities, or lack of experience and

knowledge, unless they have been given

supervision or instruction concerning use

of the appliance by a person responsible

for their safety.

Children should be supervised to ensure

that they do not play with the appliance.

FOR USERS IN THE UK, EIRE,

MALTA AND CYPRUS ONLY

IMPORTANT

• In the event of replacing the plug fuse, use a fuse

approved by ASTA to BS 1362, i.e. carrying the

mark, rating as marked on plug.

• Always replace the fuse cover. Never use plugs

with the fuse cover omitted.

• If the available electrical outlet is not suitable for

the plug supplied with this equipment, you

should contact your authorized dealer to obtain

the correct lead.

———————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—————

3

CONTENTS

IMPORTANT SAFETY INSTRUCTIONS ...........1

1. KNOWING YOUR SEWING

MACHINE .................................. 4

ACCESSORIES .................................................4

Optional accessories .......................................... 4

THE MAIN PARTS ...........................................5

Flat bed attachment ............................................ 5

USING YOUR SEWING MACHINE ................6

Connecting plugs ............................................... 6

Main power and sewing light switch .................. 7

Foot controller .................................................... 7

Checking the needle ........................................... 7

Replacing the needle .......................................... 7

Changing the presser foot ................................... 8

THE CONTROLS .............................................9

Pattern selection dial .......................................... 9

Stretch stitching .................................................. 9

Patterns and stitch names ................................. 10

Stitch length dial .............................................. 12

Stitch width dial ............................................... 12

Reverse sewing lever ........................................ 13

THREADING THE MACHINE .......................13

Winding the bobbin ......................................... 13

Lower threading ............................................... 15

Lower threading (for models equipped with a

quick-set bobbin) ............................................. 16

Upper threading ............................................... 17

Using the needle threader (for models equipped

with a needle threader) ..................................... 19

Drawing up the lower thread ............................ 21

FABRIC, THREAD, AND NEEDLE

COMBINATIONS .........................................22

2. SEWING BASICS ......................23

Please read before sewing ................................ 23

Starting sewing ................................................. 23

Trial sewing ...................................................... 24

Changing the sewing direction ......................... 24

Sewing thick fabrics ......................................... 24

Sewing thin fabrics ........................................... 25

Sewing stretch fabrics ....................................... 25

Stitching cylindrical pieces ............................... 25

Sewing with a twin needle (Option) ................. 25

Thread tension ................................................. 27

3. BUILT-IN STITCHES ................. 28

Straight stitching ...............................................28

Zigzag stitching .................................................28

Blind hem stitching ...........................................28

Shell tuck stitching ............................................30

Elastic stitching .................................................30

Double action stitching .....................................31

Fagoting ............................................................31

Overedge stitching ............................................32

Feather stitching ................................................33

Triple zigzag stretch stitching ............................33

Decorative stitching ..........................................33

4. SEWING BUTTONHOLES AND

BUTTONS ............................... 34

Making a buttonhole

(1-step automatic buttonhole) ...........................34

Adjusting buttonholes .......................................36

Sewing buttons .................................................37

5. USING ATTACHMENTS AND

APPLICATIONS ....................... 38

Zipper insertion ................................................38

Gathering ..........................................................39

Darning ............................................................39

Appliqués .........................................................39

OPTIONAL ACCESSORIES ........................... 40

Using the walking foot ......................................40

Using the quilting guide ....................................41

Using the quilting foot ......................................41

Using the 1/4-inch quilting foot ........................42

Using the narrow hemmer foot .........................42

Using the blind stitch foot .................................44

6. APPENDIX ................................ 45

MAINTENANCE ........................................... 45

Restrictions on oiling ........................................45

Precautions on storing the machine ..................45

Cleaning ...........................................................45

TROUBLESHOOTING .................................. 47

INDEX .......................................................... 50

4

—————

——————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

1

1 KNOWING YOUR SEWING MACHINE

ACCESSORIES

We have designed these accessories to help you easily perform most sewing tasks.

Note

● The included accessories vary depending on the machine model.

Optional accessories

The following are available as optional accessories to be purchased separately. Depending on the model you

purchased, the following accessory may be included with your machine.

1. 2. 3. 4. 5.

6. 7. 8. 9.

No. Part Name

Part Code

Americas Others

1

Zigzag foot “J”

(on machine)

XC4901-021

2 Buttonhole foot “A” XD1792-031

3 Zipper foot “I” XE9369-001

4 Darning Plate XC6063-021

5 Button sewing foot “M” XE2137-001

6

Bobbin

(One is on machine)

SA156

SFB:

XA5539-151

7

Needle set

(90/14 needle)

3-piece set: XE5328-001

2-piece set: XE7064-001

8 Oval screwdriver XE5241-001

9 Foot controller See page 5

No. Part Name

Part Code

Americas Others

1. 2. 3. 4. 5.

6. 7. 8.

No. Part Name

Part Code

Americas Others

1 Extra spool pin XE2241-001

2

Twin needle

(2.0/75 needle)

X57521-021

3 Walking Foot SA107

F034N:

XC2165-002

4 Quilting Foot SA129

F005N:

XC1948-052

5 1/4-inch Quilting Foot SA125

F001N:

XC1944-052

6 Narrow Hemmer Foot SA127

F003N:

XC1945-052

7 Blind Stitch Foot SA134

F018N:

XC1976-052

8 Quilting guide SA132

F016N:

XC2215-052

No. Part Name

Part Code

Americas Others

KNOWING YOUR SEWING MACHINE ————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————

—————

5

THE MAIN PARTS

1 Bobbin winder (Page 13)

This winds the thread onto the bobbin for use as the

lower thread.

2 Stitch length dial (Page 12)

Rotate the dial to control the stitch length.

3 Spool pin (Page 14, 17)

This holds the spool of thread.

4 Stitch width dial (Page 12)

Rotate the dial to control the stitch width.

5 Upper tension-control dial (Page 27)

This controls the tension of the upper thread.

6 Thread guide (Page 14, 17)

This is used when winding the thread onto the

bobbin and then threading the machine.

7 Thread take-up lever (Page 18)

8 Thread cutter (Page 24)

Pass the threads through the thread cutter to cut

them.

9 Needle threader (Page 19)

(This is only available on certain models.)

0 Quick-set bobbin (Page 16)

(This is only available on certain models.)

A Flat bed attachment with accessory compartment

(Page 5)

B Presser foot (Page 8)

C Reverse sewing lever (Page 13)

Push this lever to stitch in the reverse direction.

D Pattern selection dial (Page 9)

Rotate the dial in either direction to choose the

stitch you want.

E Handwheel

Used to manually raise and lower the needle.

F Buttonhole fine-adjustment screw (Page 36)

G Main power and sewing light switch (Page 7)

You can turn the main power and sewing light

switch on and off.

H Foot controller jack / socket (Page 6)

Plug in the foot controller plug and connect the

machine to the power supply.

I Presser foot lever (Page 18)

Used to raise and lower the presser foot.

J

Buttonhole lever (1-Step automatic buttonhole)

(

Page 34

)

Lower the buttonhole lever when sewing

buttonholes.

K Foot controller (Page 7)

You can use this to control the sewing speed, and to

start and stop sewing.

Foot Controller: Model KD-1902 for 110/120V area

Model KD-2902 for 220/240V area

The foot controller part code differs depending on the

country or region. Contact your dealer or the nearest

authorized service center.

Flat bed attachment

The accessories can be stored in a compartment inside

the flat bed attachment.

1

Slide the flat bed attachment to the left to

open it.

1 Flat bed attachment

2 Storage compartment

1

3

2

4

5

6

7

8

9

0

A

B

C

D

G

F

H

I

K

E

J

1

2

6

—————

——————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

1

USING YOUR SEWING MACHINE

WARNING

CAUTION

Connecting plugs

1

Connect the foot controller plug to the

machine.

2

Connect the power supply plug to a wall

outlet.

Note

● If a power outage occurs while the sewing

machine is being operated, turn off the main

power and unplug the power supply cord.

When restarting the sewing machine, follow

the necessary procedure to correctly operate

the machine.

(For U.S.A. only)

● This appliance has a polarized plug (one

blade wider than the other). To reduce the

risk of electric shock, this plug is intended to

fit in a polarized outlet only one way. If the

plug does not fit fully in the outlet, reverse

the plug.

If it still does not fit, contact a qualified

electrician to install the proper outlet. Do

not modify the plug in any way.

● Use only regular household electricity for the power source. Using other power sources may

result in fire, electric shock, or damage to the machine.

● Make sure that the plugs on the power cord are firmly inserted into the electrical outlet and

the power supply jack on the machine.

● Do not insert the plug on the power cord into an electrical outlet that is in poor condition.

● Turn off the main power and remove the plug in the following circumstances:

• When you are away from the machine

• After using the machine

• When the power fails during use

• When the machine does not operate correctly due to a bad connection or a disconnection

• During electrical storms

● Use only the power cord included with this machine.

● Do not use extension cords or multi-plug adapters with many other appliances plugged in to

them. Fire or electric shock may result.

● Do not touch the plug with wet hands. Electric shock may result.

● When unplugging the machine, always turn off the main power first. Always grasp the plug to

remove it from the outlet. Pulling on the cord may damage the cord, or lead to fire or electric

shock.

● Do not allow the power cord to be cut, damaged, modified, forcefully bent, pulled, twisted,

or bundled. Do not place heavy objects on the cord. Do not subject the cord to heat. These

things may damage the cord and cause fire or electric shock. If the cord or plug is damaged,

take the machine to your authorized dealer for repairs before continuing use.

● Unplug the power cord if the machine is not to be used for a long period of time. Otherwise

a fire may result.

2

1

KNOWING YOUR SEWING MACHINE ————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————

—————

7

Main power and sewing

light switch

This switch turns the main power and sewing light on or

off.

1 Turn on (toward the ‘I’ mark)

2 Turn off (toward the ‘O’ mark)

Foot controller

When you press the foot controller down lightly, the

machine will run at a low speed. When you press

harder, the machine’s speed will increase. When you

take your foot off the foot controller, the machine will

stop.

1 Slower

2 Faster

You should make sure that nothing is placed on the foot

controller when the machine is not in use.

CAUTION

Note

(For U.S.A. only)

● Foot Controller: Model KD-1902

This foot controller can be used on the

machine with product code 885-X06,

885-X08, 885-X26, 885-X28.

The product code is mentioned on the

machine rating plate.

Checking the needle

The sewing needle must always be straight and sharp

for smooth sewing.

■ Checking the needle correctly

Put the flat side of the needle on a flat surface.

Check the needle from the top and the sides.

Dispose of any bent needles safely.

1 Parallel space

2 Level surface (bobbin cover, glass, etc.)

Replacing the needle

CAUTION

1

Turn off the machine.

2

Raise the needle by turning the

handwheel toward you

(counterclockwise) so that the mark on

the wheel points up.

3

Lower the presser foot lever.

1 Presser foot lever

● Do not allow pieces of cloth and dust to

build up on the foot controller. Doing so

could cause a fire or an electric shock.

2

1

2

● Always turn off the machine before you

change the needle. Otherwise, injuries

may occur if the foot controller is

accidentally pressed and the machine

starts sewing.

● Only use sewing machine needles for

home use. Other needles may bend or

break and cause injury.

● Never sew with a bent needle. A bent

needle will easily break and cause injury.

1

2

1

8

—————

——————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

1

CAUTION

4

Hold the needle with your left hand, and

then use an oval screwdriver to turn the

needle clamp screw counterclockwise to

remove the needle.

1 Use an oval screwdriver

2 Needle clamp screw

• Do not use excessive force when loosening

or tightening the needle clamp screw,

otherwise certain parts of the sewing

machine may be damaged.

5

With the flat side of the needle toward the

back of the machine, insert the needle

until it touches the needle stopper. Next,

tighten the needle clamp using an oval

screwdriver.

Install the twin needle in the same way.

CAUTION

Changing the presser foot

CAUTION

You will have to change the presser foot depending on

what you want to sew and how.

1

Turn off the machine.

Raise the presser foot lever.

2

Raise the needle by turning the

handwheel toward you

(counterclockwise) so that the mark on

the wheel points up.

3

Press the black button at the back of the

presser foot holder to release the presser

foot.

4

Put a different presser foot on the needle

plate so that the bar on the presser foot is

in line with the slot on the shank.

● Before replacing the needle, place fabric

or paper under the presser foot to

prevent the needle from falling into the

hole in the needle plate.

1 Use an oval

screwdriver

2 Needle stopper

3 Needle

21

2

3

1

● Make sure you insert the needle until it

touches the stopper, and securely tighten

the needle clamp screw with an oval

screwdriver, otherwise the needle may

break or the machine may be damaged.

● Always turn off the machine before you

change the presser foot. If you leave the

power on and step on the controller, the

machine will start and you may be

injured.

● Always use the correct presser foot for

the stitch pattern you have chosen. If

you use the wrong presser foot, the

needle may strike the presser foot and

bend or break, and may cause injury.

● Only use presser feet that have been

designed to be used with this machine.

Using any other presser foot may cause

accident or injury.

1 Black button

2 Presser foot holder

3 Presser foot

1

2

3

KNOWING YOUR SEWING MACHINE ————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————

—————

9

5

Lower the presser foot lever and fix the

presser foot onto the shank. If the presser

foot is in the correct place, the bar should

snap in.

1 Shank

2 Bar

■ Presser foot installation orientation

CAUTION

THE CONTROLS

Pattern selection dial

CAUTION

To choose a stitch, simply turn the pattern selection dial

in either direction. The next section shows

recommended stitch lengths and widths.

1 Pattern selection dial

2 Chosen pattern number

Stretch stitching

Raise the needle by turning the handwheel toward you

(counterclockwise) so that the mark on the wheel points

up.

Setting the stitch length dial to “ ” changes the

selected pattern to a stretch stitch.

1

2

● If the presser foot is not installed with

the correct orientation, the needle may

strike the presser foot, which may bend

or break the needle and cause injury.

● When you use the pattern selection dial

to choose a pattern, raise the needle by

turning the handwheel toward you

(counterclockwise) so that the mark on

the wheel points up. If the needle is in

the down position when you turn the

pattern selection dial, the needle, presser

foot or fabric may be damaged.

2

1

10

—————

——————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

1

Patterns and stitch names

■ 37 Stitches

(only available on certain models)

■ 27 Stitches

1

2

3

4

5

6

7

8 9 10

11

12

13

14

15

16

17

18

19

20

21

22

23 24

25

26

27

28

29

30

31

32

33

34

35

36

37

1

2

3

4

5

6

7

8 9 10

11

12

13

14

15

16 17 18 19

20

21

22

23

24

25

26

27

Pattern

Stitch Name

Recommended

Width

(mm (inch))

Recommended

Length

(mm (inch))

Reference Page

37 Stitches 27 Stitches

1-STEP AUTOMATIC

BUTTONHOLE

3-5

(1/8 – 3/16)

F-1.5

(1/64-1/16)

34

STRAIGHT STITCH

0-5 (0-3/16)

(Changes needle

position)

1-4

(1/16-3/16)

28, 38, 39, 40,

41, 42, 44

ZIGZAG STITCH

0-5

(0-3/16)

F-4

(1/64-3/16)

28, 37, 39, 40,

44

BLIND HEM STITCH

3-5

(1/8-3/16)

F-2

(1/64-1/16)

28, 44

SHELL TUCK STITCH

3-5

(1/8-3/16)

F-3

(1/64-1/8)

30

ELASTIC STITCH

3-5

(1/8-3/16)

F-2.5

(1/64-3/32)

30

STRETCH BLIND HEM

STITCH

3-5

(1/8-3/16)

F-1.5

(1/64-1/16)

28

SCALLOP STITCH

3-5

(1/8-3/16)

F-1.5

(1/64-1/16)

33

DOUBLE ACTION STITCH

3-5

(1/8-3/16)

F-3

(1/64-1/8)

31

BRIDGING STITCH

3-5

(1/8-3/16)

F-3

(1/64-1/8)

31

RAMPART STITCH

3-5

(1/8-3/16)

F-3

(1/64-1/8)

31

ELASTIC SHELL TUCK

STITCH

3-5

(1/8-3/16)

F-3

(1/64-1/8)

32

1 1

2

3 3

4

5 5

6

7 7

8

9 9

10

11 11

12

Page is loading ...

12

—————

——————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

1

Stitch length dial

Depending on the selected stitch, you may need to

adjust the stitch length for best results.

The numbers marked on the stitch length dial represent

the stitch length in millimeters (mm) (1/25 inch).

THE HIGHER THE NUMBER, THE LONGER THE

STITCH. With the “0” setting, material is not fed. This is

used when sewing a button.

The “F”-“1” range is for making a satin stitch (closed

zigzag stitch), which is used for making buttonholes

and decorative stitches. The position needed for making

the satin stitch varies according to the material and

thread being used. To determine the exact dial position,

first test the stitch and length settings on a scrap piece of

fabric to observe the feeding of the material.

1 Stitch length dial

2 Shorter

3 Longer

CAUTION

Stitch width dial

Raise the needle by turning the handwheel toward you

(counterclockwise) so that the mark on the wheel points

up. The numbers marked on the dial represent the stitch

width.

1 Stitch width dial

When the Straight or Triple Stretch Stitch is selected, the

needle position can be changed from left to right by

adjusting the stitch width dial.

DECORATIVE STITCH

5

(3/16)

Fixed

2.5 (3/32)

33

— DECORATIVE STITCH

5

(3/16)

Fixed

2.5 (3/32)

33

— DECORATIVE STITCH

5

(3/16)

Fixed

2.5 (3/32)

33

— LINK STITCH

5

(3/16)

Fixed

2.5 (3/32)

33

— DECORATIVE STITCH

3-5

(1/8-3/16)

Fixed

2.5 (3/32)

33

— DECORATIVE STITCH

5

(3/16)

Fixed

2.5 (3/32)

33

Pattern

Stitch Name

Recommended

Width

(mm (inch))

Recommended

Length

(mm (inch))

Reference Page

37 Stitches 27 Stitches

32

27

33

34

35

36

37

1

2

3

1

● If the stitches are bunched together,

lengthen the stitch length and continue

sewing. Do not continue sewing without

lengthening the stitch length, otherwise

the needle may break and cause injury.

1

KNOWING YOUR SEWING MACHINE ————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————

—————

13

CAUTION

Reverse sewing lever

You can use reverse sewing for back tacking and

reinforcing seams.

To sew in reverse, push the reverse sewing lever in as

far as possible and hold it in that position while you

lightly push the foot controller. To sew forward, release

the reverse sewing lever. The machine will then sew

forward.

1 Reverse sewing lever

THREADING THE MACHINE

Winding the bobbin

CAUTION

● After adjusting the stitch width, slowly

turn the handwheel toward you

(counterclockwise) and check that the

needle does not touch the presser foot. If

the needle hits the presser foot, the

needle may bend or break.

● If the stitches are bunched together,

increase the stitch length. Continuing to

sew with the stitches bunched together

may result in the needle bending or

breaking.

1

● We designed the bobbin that comes with this machine. If you use bobbins from other models,

the machine will not work properly. Only use the bobbin that comes with this machine or

bobbins of the same type (part code: SA156, SFB: XA5539-151). Using other bobbins may

cause damage to the machine.

Actual size

11.5 mm

(7/16 inch)

This model Other models

14

—————

——————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

1

Pull up the spool pin and put a spool of

thread on this pin.

2

While holding the thread from the spool

with your right hand, pass the thread

toward you, in the groove on the thread

guide. Then, pass the thread around the

pre-tension disk and pull the thread in

completely.

1 Pre-tension disk

CAUTION

3

Pass the end of the thread through the

hole on the bobbin from the inside of the

bobbin.

4

Put the bobbin onto the bobbin winder

shaft and slide the bobbin winder shaft to

the right. Turn the bobbin clockwise, by

hand, until the spring on the shaft slides

into the notch of the bobbin.

• Make sure to pull out 7 to 10 cm (3-4 inches)

of thread from the hole on the bobbin.

1 Spring on the shaft

2 Notch

3 7-10 cm (3-4 inches)

CAUTION

5

Turn on the machine.

1 Pre-tension disk 2 Bobbin winder shaft 3 Bobbin

1

3

2

1 Pull the thread

in completely.

● If the spool of thread is in the wrong

place, or is set incorrectly, the thread

may tangle on the spool pin.

1

● Pull the thread taut and hold the end of

the thread straight up. If the thread is too

short, not pulled taut or held at an angle,

injuries may occur when the thread is

wound around the bobbin.

3

1

2

KNOWING YOUR SEWING MACHINE ————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————

—————

15

6

While holding the end of the thread,

gently press the foot controller to wind

the thread around the bobbin a few times.

Then stop the machine.

7

Trim the excess thread above the bobbin.

1 1 cm (1/2 inch)

CAUTION

8

Press the foot controller to start.

9

When the bobbin seems full and begins

spinning slowly, take your foot off the foot

controller.

0

Cut the thread, slide the bobbin winder

shaft to the left and remove the bobbin.

Note

● When the sewing machine is started or the

handwheel is turned after winding the thread

around the bobbin, the machine will make a

clicking sound; this is not a malfunction.

● The needle bar does not move when you slide

the bobbin winder shaft to the right.

CAUTION

Lower threading

Install the bobbin wound with thread.

• For more details on using the quick-set

bobbin, see page 16.

CAUTION

1

Prepare the bobbin wound properly

before threading the lower thread.

• See page 13 for the details about bobbin

winding.

2

Raise the needle by turning the

handwheel toward you

(counterclockwise) and raise the presser

foot lever.

3

Remove the bobbin cover by sliding it and

lift toward you.

1 Bobbin cover

● Make sure you follow the instructions

carefully. If you do not cut the excess

thread completely before winding the

bobbin, when the thread runs low it may

tangle around the bobbin and cause the

needle to break.

1

● Not winding the bobbin properly may

cause the thread tension to loosen, and

may break the needle.

1 Wound evenly

2 Wound poorly

● Make sure you turn off the machine

while threading. If you accidentally step

on the foot controller and the machine

starts to sew, you could be injured.

1 2

1

16

—————

——————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

1

4

Put the bobbin in so the thread comes out

in the direction shown by the arrow.

CAUTION

5

Hold the end of the thread, push the

bobbin down with your finger, and then

pass the thread through the slit, as shown.

• If the thread is not correctly inserted through

the tension-adjusting spring of the bobbin

case, it may cause incorrect thread tension.

1 Tension-adjusting spring

6

Replace the bobbin cover. Put the

projection into the race retainer groove

and push closed.

1 Groove

2 Projection

• Make sure that the end of the thread comes

out from the cover toward the rear of the

machine (as shown in the illustration).

• Draw up the lower thread before starting

sewing. Refer to “Drawing up the lower

thread” on page 21 after threading the upper

thread.

Lower threading (for

models equipped with a

quick-set bobbin)

Install the bobbin wound with thread.

This feature is only available on certain models.

1

Follow steps 1 to 4 from “Lower

threading” on page 15.

2

While lightly holding down the bobbin

with your right hand as shown, guide the

thread through the slit (

1 and 2). Then,

pull the thread toward you to cut it with

the cutter (

3).

• At this time, check that the bobbin easily

rotates counterclockwise.

1 Slit

2 Cutter (Cut the thread with the cutter.)

● Make sure you set the bobbin so the

thread unrolls in the right direction. If

the thread unrolls in the wrong

direction, it may cause the thread

tension to be incorrect or break the

needle.

1

2

1

2

3

1

KNOWING YOUR SEWING MACHINE ————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————

—————

17

Note

● If the thread is not correctly inserted through

the tension-adjusting spring of the bobbin

case, it may cause incorrect thread tension.

1 Tension-adjusting spring

3

Replace the bobbin cover. Put the

projection into the race retainer groove

and push closed.

1 Groove

2 Projection

• Start sewing after threading the lower and

upper thread. When sewing gathers or darts,

you can draw up the lower thread by hand so

that some thread will be left over. Refer to the

steps in “Drawing up the lower thread”

(page 21).

Upper threading

1 Spool pin

2 Thread guide (back)

3 Thread guide (front)

4 Thread take-up lever

5 Mark on the handwheel

CAUTION

1

2

● When threading the upper thread, carefully follow the instructions. If the upper threading is

not correct, the thread may become tangled or the needle may bend or break.

● Never use a thread weight of 20 or lower.

● Use the needle and the thread in the correct combination. For details on the correct

combination of needles and threads, refer to “FABRIC, THREAD, AND NEEDLE

COMBINATIONS” on page 22.

4

3

2

1

5

18

—————

——————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

1

Turn off the machine.

2

Raise the presser foot lever.

1 Presser foot lever

3

Raise the needle by turning the

handwheel toward you

(counterclockwise) so that the mark on

the wheel points up.

• If the needle is not correctly raised, the

sewing machine can not be threaded.

1 Mark on the wheel

4

Pull up the spool pin and put a spool of

thread on this pin.

CAUTION

5

While holding the thread from the spool

with your right hand, pass the thread

toward you, in the groove on the thread

guide.

• Make sure that the spring in the groove

catches the thread.

1 Spring

6

Feed the upper thread as shown in the

following illustration.

7

Make sure you guide the thread through

the thread take-up lever from right to left

as shown in the following illustration.

1 Thread take-up lever

Memo

● If the thread take-up lever is lowered, the

upper thread can not be wrapped around

the thread take-up lever. Make sure you

raise the needle by turning the handwheel

toward you (counterclockwise) so that the

mark on the wheel points up.

● If the spool of thread is in the wrong

place, or is set incorrectly, the thread

may tangle on the spool pin and cause

the needle to break.

1

KNOWING YOUR SEWING MACHINE ————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————

—————

19

8

Put the thread behind the guide above the

needle.

• The thread can easily be passed behind the

needle bar thread guide by holding the

thread in your left hand, then feeding the

thread with your right hand.

1 Needle bar thread guide

9

Thread the needle from front to back

leaving a thread tail of about 5 cm

(2 inch).

• If your sewing machine is equipped with a

needle threader, use the needle threader to

thread the needle (see next section).

1 5 cm (2 inch)

Note

● Make sure you raise the presser foot lever

and the thread take-up lever before you feed

the upper thread.

● If you incorrectly feed the thread you may

cause sewing problems.

Using the needle threader

(for models equipped with

a needle threader)

This feature is only available on certain models.

CAUTION

1

Follow steps 1 to 8 from “Upper

threading” on page 17 before using the

needle threader.

2

Lower the presser foot lever.

3

Make sure that the mark on the wheel

points up as shown in the following

illustration.

1 Mark on the wheel

4

While lowering the needle threader lever,

hook the thread onto the guide.

1 Needle holder

2 Needle threader lever

1

● The needle threader can be used with a

75/11 through 100/16 home sewing

machine needle. However, the needle

threader cannot be used with a 65/9

home sewing machine needle. When

using special thread such as transparent

nylon thread or metallic thread, the

needle threader cannot be used.

● Thread with a thickness of 130/120 or

thicker cannot be used with the needle

threader.

● The needle threader cannot be used with

the wing needle or the twin needle.

● If the needle threader cannot be used,

refer to “Upper threading” on page 17.

1

2

20

—————

——————————————————————————————————————————————————————————————————————————

—

————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

1

1 Needle holder

2 Needle threader lever

3 Guide

5

Pull down the needle threader lever as

much as possible, and then turn the lever

toward the back of the machine (away

from you). Make sure that the hook passes

through the eye of the needle and grabs

the thread.

1 Hook

2 Thread

• Hold the thread in front of the needle to

make sure that the hook grabs it.

6

While lightly holding the thread, turn the

needle threader lever toward the front of

the machine (toward you). The hook will

pull the thread through the needle.

7

Raise the needle threader lever.

8

Pull the loop of the thread passed through

the eye of the needle toward the rear of

the machine.

1 Loop of thread

CAUTION

9

Raise the presser foot lever.

1

2

3

1 21

● Be careful not to pull on the thread with

force or it may bend the needle.

● If the thread does not pass through the

eye of the needle, start from step

3

again.

1

KNOWING YOUR SEWING MACHINE ————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————

—