Powermate PW0872300 User manual

Brand: Powermate

Model: PW0872300

Category: High-pressure cleaners

Type: User manual

08/05 0063327

IMPORTANT - Please make

certain that everyone who uses

the Pressure Washer thoroughly

reads and understands these

instructions prior to operation.

IMPORTANT - Veiller à ce que

toute personne amenée à utiliser

cet appareil de lise soigneusement

ces instructions et les comprenne

avant de procéder à son

utilisation.

IMPORTANTE - Favor de

ceciorarse de que toda persona

que use el Lavador de presión

lea y entienda todas las

instrucciones antes de la

operación.

PW0872300

Insert

Additif

Adición

REF. PART DESCRIPTION DESCRIPTION DESCRIPCION

NO. NO.

10057648Faip Pump PompeBomba1

2Note AEngine MoteurMotor1

30055894Rubber FootPiedPie2

4Note BNyloc Nut 5/16-18Ecrou autofreinéTuerca de nyloc3

50063255CarrierEnsemble de transportTransportador, conjunto1

60063326Bolt L 1/4-20 x 3.75BoulonPerno1

70058081HoseTuyauManguera1

8Note BNyloc Nut 1/4-20Ecrou autofreinéTuerca de nyloc3

9Note BBolt 5/16-18 X 2.00BoulonPerno3

100063315HandlePoignéeMango1

110057741Vinyl round capCapuchon de rond de vinyleRedondo Vinilo Gorro1

120057704WheelRoueRueda2

130053188Hub capChapeau, essieuTapa de eje2

140061351Gun assemblyPistoletPistola1

150058612Assy, wandEnsemble de baguetteConjunto de varilla1

16Note BWasher Flat 1/4Rondelle, plateArandela plana2

170062098Key SQ 3/16 x 3/16 Gib HeadToucheTecla1

180057701Chemical HoseTuyau pour les produits chimiquesManguera de sustancia química1

190000087Chemical filterFiltre pour les produits chimiquesFiltro de sustancia química1

200061439Thermal Relief ValveSoupape de surpession thermiqueVálvula de descarga de calor1

210057827SpacerEntretoiseEspaciador3

220058613NozzleBuseBoquilla1

230000085Chemical ConnectorConnecteur pour les produits Conectora de sustancia química 1

chimiques

24Note BBolt 1/4-20 x 1.25BoulonPerno2

25Note BNut hex 1/4-20EcrouTuerca1

260063132Handle release buttonBouton de déclenchementBotone de liberación la manija1

PARTS LIST / LISTE DES PIÈCES / LISTA DE PIEZAS

PARTS DRAWING / SCHEMA DES PIÈCES / DIAGRAMA DE PIEZAS

Note A: Powermate Corporation will not provide engines as replacement parts. Engines are covered through the engine manufacturer’s warranty. Consult the

accompanying engine manual or contact our service department for assistance.

Note B: These are standard parts available at your local hardware store.

Remarque A: Powermate Corporation ne fournit pas de moteurs dans ses pièces de rechange. Le moteur est couvert par la garantie du fabricant. Consulter

le manuel du moteur inclus ou contacter notre service après-vente pour toute assistance.

Remarque B: Ces pièces sont des pièces standard disponibles dans les quincailleries.

Nota A: Powermate Corporation no proporcionará motores como piezas de repuesto. Los motores están cubiertos por medio de la garantía del fabricante del

motor. Consulte el manual adjunto del motor o comuníquese con nuestro departamento de servicio para recibir asistencia al respecto.

Nota B: Estas son piezas estándar disponibles en su ferretería local.

PARTS DRAWING / SCHEMA DES PIÈCES / DIAGRAMA DE PIEZAS

PARTS LIST / LISTE DES PIÈCES / LISTA DE PIEZAS

REF. PART DESCRIPTION DESCRIPTION DESCRIPCION

NO. NO.

0057648Pump Assembly MPTV82164PompeEnsamble de la bomba1

10058498Seal 15203000JointSello1

20058499Elastic ring 13301000Anneau élastiqueAro elástico1

30059021Seal 13301200JointSello1

40059022Bearing disc 17400100Grain de crapaudine Disco de cojinete1

50059023Needle bearing 16900100Roulement à aiguillesCojinete de aguja2

90059024Flange MFVR82222Dride d’adaptation Pestaña de adaptación1

110058506Beraring disc 17400200Grain de crapaudine Disco de cojinete1

120058507Needle bearing 16900200Roulement à aiguillesCojinete de aguja1

130059025Wobble plate 57141300Plateau oscillant Placa oscilante1

REF. PART DESCRIPTION DESCRIPTION DESCRIPCION

NO. NO.

140058509Cap 57130600ChapeauTapa1

150058510Bearing disc 57133100Grain de crapaudineDisco de cojinete1

160058533O-ring 15024000Joint torique Aro1

170058632Carter 57140400CharretierCárter1

180058534O-ring 15001500Joint torique Aro3

200059026Bearing 16003500RoulementCojinete1

210058653Screw 10801600Vis Tornillo1

220058532O-ring 15000900Joint torique Aro1

230059027O-ring 15062400Joint torique Aro1

240058538O-ring 15000100Joint torique Aro2

250058539O-ring 15064200Joint torique Aro3

260058540Valve assemly 52022500Ensemble soupapeEnsamble de válvula6

270058541O-ring 15060500Joint torique Aro4

280058633Manifold 23732300/ACollecteurDistribuidor1

310058545Chemical Spring 50136200RessortResorte1

320058546Ball 3/16 stainless steel 17600300BilleRodamiento 3/16 acero inoxidable1

330058943O-ring 15001400Joint torique Aro1

340058548Chemical dosing body 52036700Corps de dosage chimiqueCuerpo de dosificación química1

350058549O-ring 15000600Joint torique Aro1

360058550Cemical dosing screw 50139700Vis de dosage chimiqueTornillo de dosificación química1

370059028No return valve 52032700Clapet de non-retourVálvula sin retorno1

380058552Spring 52032801RessortResorte1

390059029Injector nozzle 52032500InjecteurBoquilla de inyector1

400058554O-ring 15062600Joint torique Aro1

410058555O-ring 15001300Joint torique Aro2

420059029Injection nipple hobby 52032500Mamelon d’injectionEntrerrosca de inyección1

430058512Under-cap 18104600CouvercleCubierta inferior1

440059030Screw 10205200VisTornillo1

450058634By-pass pin 52234500/aGoupille de dérivation Clavija de paso1

460058558Valve seat plate 52068000Plaque de siège de soupapePlaca base de la vàlvula1

470059031Vavle seat 52052302/BSiège de soupapeAro posterior1

480058560Back-ring 15100100 Bague antiextrusion Aro posterior1

490058561O-ring 15001100Joint torique Aro1

500058636By-pass valve body 52036501Corps de soupape de dérivation en plastique Cuerpo plástico de la válvula de paso1

510058563Plug 52038300Bouchon Tapón1

520058564Ball 7mm stainless steel 17600900Bille de 7mm en inox.Rodamiento de acero inoxidable de 7mm1

530059032By-pass piston 52070600Piston de dérivation en plastiquePistón de paso 1

540058638Back-ring 15101700Bague antiextrusion de joint toriqueAro posterior para aro en O1

550058639Spacer 52235301EntretoiseSeparador1

560059033Pressure Reg. spring 23740400Ressort de régulateur de pressionResorte regulador de presión1

570058641Pressure Reg. nut 52070700Vis de régulateur de pressionTornillo regulador de presión1

580058642Ring 52033600BagueAro3

590058643Piston 52076300PistonPistón3

600059034Spring 52045202Ressort Resorte3

610058517Screw 10200400VisTornillo3

620058576O-ring 15000700Joint torique Aro1

630058645Oil seal 15202400Joint d’huileSello del aceite3

640058646Brass bushing 52038801Douille en laitonBuje de bronce3

650058573O-ring 15001800Joint torique Aro3

660058647Oil cap 18107600Bouchon de remplissage d'huileCubierta de llenado de aceite1

670058648High pressure seal 15501800Joint haute pressionSello de alta presión3

680058518O-ring 15065300Joint torique Aro3

690058519Valve seat 52068400Siège de soupapeBase de válvula6

700058520Valve plate 52068101Plaque porte-soupape en acier inoxydableAcero inoxidable de la placa de la válvula6

710058521Spring valve 52068300Soupape à ressortVálvula de resorte6

720058522Valve cage 52068200Cage de soupapeCaja de la válvula6

730058649Brass pump head 52045801/BTête de pompeCabeza de bomba1

740058524Screw 10204100VisTornillo5

750058543O-ring 15065000Joint torique Aro1

760059035Seal PVVR81773JointEmpaque3

770058511Under cap 18102500CouvercleCubierta inferior1

780058528O-ring 15000300Joint torique Aro1

790059036Screw 52032001VisTornillo1

800059037Clutch for chemical dosing body 52036800Embrayage du corps de dosage chimiqueEmbrague para cuerpo dosificador de químicos1

810059038Detergent hose 15611200Flexible à détergentManguera de detergente1

820058652Pin 13580500ChevilleClavija 1

840059039Filter 52037200FiltreFiltro1

850058578O-ring 15061800Joint torique Aro2

860058536Inlet extension 57136300Entrée extensionExtensión de entrada1

870058535Connection ring nut 52069100Retient écrouConexión anillo tuerca1

880058577Washer 12406500RondellesArandela1

890058525Outlet extension 57136200Rallonge de refoulementExtensión de salida1

PARTS LIST / LISTE DES PIÈCES / LISTA DE PIEZAS

PRE-START PREPARATION

Before starting the pressure washer, check for loose or

missing parts and for any damage which may have occurred

during shipment.

Handle Installation

Install handle and hose hook as shown in Figure 1.

START-UP PROCEDURE

1.Make sure water supply is connected and turned on.

2.Release gun safety if locked.

3.To allow air to escape from the hose, squeeze trigger on

the gun until there is a steady stream of water coming

from the nozzle.

4.Remove any dirt or foreign matter from the gun outlet and

the male connector of the wand.

5.Insert the nozzle wand into the gun wand and tighten the

fitting securely.

STARTING THE ENGINE

1.Check oil and fuel level.

2.Set the engine switch to the “ON” position.

3.Push the primer as necessary.

4.Squeeze trigger on pressure washer to release pressure

while pulling on the engine starter rope with a fast steady

pull. Pressure may otherwise build up making starting the

unit difficult.

HIGH PRESSURE HOSE

Attach the high pressure hose to the fitting located on the

front side of the side panel. Only Coleman Powermate

Pressure Washer high pressure hoses should be used.

WATER CONNECTION

Before connecting the inlet hose to the unit, run water

through the garden hose (not supplied) to flush out any foreign

matter. The inlet hose will be connected to the fitting.

See Figure 1.

RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Up to 3540

GPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2.1 GPM

Maximum Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2300 psi

Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5 oz.

The high pressure nozzle position is intended for clean-

ing. When high pressure is required, grasp collar and slide the

collar and nozzle toward the gun.

NOTE: Make sure the nozzle cover is pulled to the

extreme rear position to lock the nozzle in the high pres-

sure position.

When low pressure is required, grasp and slide the nozzle

cover away from the gun.

The adjustable spray nozzle can adjust spray from fan to

pencil point in both the high and low pressure positions. The

spray is adjusted by turning the nozzle cover.

CAUTION: The pencil point spray adjustment

is very aggressive. We recommend that for most

cleaning applications, a twenty degree (20°)

spray angle be used to avoid damage to the

surface being sprayed.

START-UP PROCEDURE SPECIFICATIONS

HIGH PRESSURE/LOW PRESSURE

ADJUSTABLE SPRAY NOZZLE

OPERATING CONNECTIONS

English

Low Pressure

High Pressure

Pin Point Spray

To decrease angle to a pencil point

spray, turn clockwise.

FanSpray

To increase angle to a fan spray,

turn counterclockwise.

Figure 1

Page is loading ...

Powermate Corporation

4970 Airport Road

P. O. Box 6001

Kearney, NE 68848

1-800-445-1805

1-308-237-2181

Fax 1-308-234-4187

Powermate ® is a registered trademark of Powermate Corporation.

Powermate® est une marque déposée de Powermate Corporation.

Powermate ® es una marca comercial registrada de Powermate Corporation.

Powermate PW0872300 User manual

Brand: Powermate

Model: PW0872300

Category: High-pressure cleaners

Type: User manual

Download PDF

report

in other languages

français: Powermate PW0872300 Manuel utilisateur
español: Powermate PW0872300 Manual de usuario

Powermate PW0872300 User manual

Powermate PW0872300 User manual

in other languages

Related papers

Other documents