Calvin Klein PW0881900 User manual

PW0881900 INSERT

www.colemanpowermate.com LFL 06/04 0062414

IMPORTANT - Please make

certain that everyone who uses

the Coleman® Powermate®

Pressure Washer thoroughly

reads and understands these

instructions prior to operation.

IMPORTANT - Veiller à ce que

toute personne amenée à utiliser cet

appareil de Coleman® Powermate®

lise soigneusement ces instructions

et les comprenne avant de procéder

à son utilisation.

IMPORTANTE - Favor de

ceciorarse de que toda persona

que use el Lavador de presión

Coleman® Powermate® lea y

entienda todas las instrucciones

antes de la operación.

REF. PART DESCRIPTION DESCRIPTION DESCRIPCION

NO. NO.

1 0058700Faip Pump PompeBomba1

2Note AEngine 3.5 Sprint B&SMoteurMotor1

30048736Nyloc Nut 5/16-18Ecrou autofreinéTuerca de nyloc3

50052068Key SQ 3/16 x .88ToucheTecla1

60057756CarrierEnsemble de transportTransportador, conjunto1

70052336Rubber FootPiedPie4

8Note BBolt 1/4-20 x 1.25BoulonPerno2

10Note BNyloc Nut 1/4-20Ecrou autofreinéTuerca de nyloc6

11Note BBolt 5/16-18 x 1.50”BoulonPerno3

120054732HandlePoignéeMango1

130058081Hose 25’ x 1/4”TuyauManguera1

140057837Gun Assy.PistoletPistola1

150058804Assy, wand & quick connectBaguette et branchement rapideEnsamblado de varilla de pulverización1

160055199NozzleBuseBoquilla1

170000085Chemical connectorConnecteur pour les produits Conectora de sustancia química1

chimiques

180057701Chemical hoseTuyau pour les produits chimiquesManguera de sustancia química1

190000087Chemical filterFiltre pour les produits chimiquesFiltro de sustancia química1

20Note BBolt 1/4-20 x 1.50BoulonPerno4

*0061439Thermal Relief ValveSoupape de surpession thermiqueVálvula de descarga de calor1

PARTS LIST / LISTE DES PIÈCES / LISTA DE PIEZAS

PARTS DRAWING / SCHEMA DES PIÈCES / DIAGRAMA DE PIEZAS

Note A: Coleman Powermate, Inc. will not provide engines as replacement parts. Engines are covered through the engine

manufacturer’s warranty. Consult the accompanying engine manual or contact our service department for assistance.

Note B: These are standard parts available at your local hardware store.

Remarque A: Coleman Powermate, Inc. ne fournit pas de moteurs dans ses pièces de rechange. Le moteur est couvert par la

garantie du fabricant. Consulter le manuel du moteur inclus ou contacter notre service après-vente pour toute

assistance.

Remarque B: Ces pièces sont des pièces standard disponibles dans les quincailleries.

Nota A: Coleman Powermate, Inc. no proporcionará motores como piezas de repuesto. Los motores están cubiertos por medio

de la garantía del fabricante del motor. Consulte el manual adjunto del motor o comuníquese con nuestro

departamento de servicio para recibir asistencia al respecto.

Nota B: Estas son piezas estándar disponibles en su ferretería local.

REF. PARTDESCRIPTION DESCRIPTION DESCRIPCIONQTY

NO. NO.

0058700Pump Assembly PompeEnsamble de la bomba1

10058498Seal 15203000JointSello1

20058499Elastic Ring 13301000Anneau élastiqueAro elástico1

30058531Vented Valve assy 57015402Ensemble soupape de ventilationEnsamble de válvula con ventilación1

40058500Oil Vented Valve 52045401 Soupape de ventilation des vapeurs d'huile Válvula de aceite con ventilación1

50058501O-Ring 15001600Joint toriqueAro1

60058664Oil Vented Cap 52045302Chapeau d’évacuation Tapa del respiradero1

70058503O-Ring 15602200Joint toriqueAro1

80058504Spring Vented Valve 52067400Soupape de ventilation à ressortVálvula de resorte con ventilación1

90058505Flange 57138700BridePestaña1

100058532O-Ring 15000900Joint toriqueAro1

PUMP

PARTS DRAWING / SCHEMA DES PIÈCES / DIAGRAMA DE PIEZAS

REPAIR KITS/KITS DE REPARACIÓN PARA/KITS DE REPARACIÓN PARA

REF. PART DESCRIPTION DESCRIPTION DESCRIPCION

NO. NO.

10058488Inlet KitNécessaire d'admissionKit de conexión de entrada

20058489Outlet KitNécessaire de refoulementKit de conexión de salida

30058490Oil Seal KitNécessaire de bagues d'étanchéitéKit de sello de aceite

40058491Packing KitNécessaire de garnituresKit de empaque

50058492Valve KitNécessaire de soupapesKit de válvula

60058493Unloader CheckClapet de marche à videVerificación del descargador

70058494Injector RepairTrousse de réparation d'injecteurReparación del inyector

80058658 Unloader SetEnsemble dispositif de marche à videConjunto del descargador

90058659Unloader StemTige du dispositif de marche à videVarilla del descargador

100058660Manifold AssemblyEnsemble collecteurEnsamble de distribuidor

PARTS LIST / LISTE DES PIÈCES / LISTA DE PIEZAS

REF. PARTDESCRIPTION DESCRIPTION DESCRIPCION

NO. NO.

110058506Bearing Disc 17400200Grain de crapaudineDisco de cojinete3

120058507Needle Bearing 16900200Roulement à aiguillesCojinete de aguja2

130058508Wobble Plate 59131801Plateau oscillantPlaca oscilante1

140058509Cap 57130600ChapeauTapa1

150058510Bearing Disc 57133100Grain de crapaudineDisco de cojinete1

160058533O-Ring 15024000Joint toriqueAro3

170058529Carter 57137900CharretierCárter1

180058534O-Ring 15001500Joint toriqueAro3

200058535Connection Ring 52069100Bague de raccordementAro de conexión1

210058536Inlet Extension 57136300Rallonge d'admissionExtensión de entrada1

220058537Gasket with Filter 52052100Ensemble joint et filtreEmpaque con filtro1

230058511Under Cap 18102500CouvercleCubierta inferior1

240058538O-Ring 15000100Joint toriqueAro3

250058539O-Ring 15064200Joint toriqueAro3

260058540Valve Assy 52022500Ensemble soupapeEnsamble de válvula6

270058541O-Ring 15060500Joint toriqueAro4

280058542Manifold 23732300CollecteurDistribuidor1

290058543O-Ring 15065000Joint toriqueAro1

300058544Screw M6 10801900VisTornillo1

310058545Chemical Spring 50136200RessortElasticidad química1

320058546Ball 3/16 17600300Bille de 6 mm en inox.Rodamiento de acero inoxidable de 6mm.1

330058943O-Ring 15001400Joint toriqueAro1

340058548Chemical Dosing Body 52036700Corps de dosage chimiqueCuerpo de dosificación química1

350058549O-Ring 15000600Joint toriqueAro1

360058550Chemical Dosing Screw 50139700Vis de dosage chimiqueTornillo de dosificación química1

370059028No Return Valve50139700Clapet de non-retourVálvula sin retorno1

380058552Spring 52032801Ressort Resorte1

390059029Injector nozzle 52032500InjecteurBoquilla de inyector1

400058554O-Ring 15062600Joint toriqueAro1

410058555O-Ring 15001300Joint toriqueAro2

420058556Injection Nipple Hobby 52032601Mamelon d'injectionEntrerrosca de inyección1

430058512Under Cap 18104600CouvercleCubierta inferior1

440058513Screw M5 10203200VisTornillo4

450058634By-Pass pin 52234500Goupille de dérivationClavija de paso1

460058558Valve Seat Plate 52068000Plaque de siège de soupapePlaca base de la válvula1

470058635Valve Seat 52052302/ASiège de soupapeBase de la válvula1

480058560Back Ring 15100100Bague antiextrusionAro posterior1

490058561O-Ring 15001100Joint toriqueAro1

500058636By-Pass valve plastic body 52036501Corps de soupape de dérivation en plastiqueCuerpo plástico de la válvula de paso1

510058563Plug 52038300BouchonTapón1

520058564Ball 7mm 17600900Bille de 7 mm en inox.Rodamiento de acero inoxidable de 7mm.1

530058565By-Pass Brass Piston 52235600Piston de dérivation en plastiquePistón de paso 1

540058638Back-Ring for 0-Ring 15101700Bague antiextrusion de joint toriqueAro posterior para aro en O1

550058639Spacer 52235301EntretoiseSeparador1

560058640Pressure Reg. spring 23731400/BRessort de régulateur de pressionResorte regulador de presión1

570058641Pressure Reg. screw 52070700Vis de régulateur de pressionTornillo regulador de presión1

580058514Ring 52548000BagueAro3

590058515Piston 52563600PistonPistón3

600058516Spring 52045201Ressort Resorte3

610058517Screw 10200400VisTornillo3

620058570O-Ring 15065600Joint toriqueAro2

630058571Oil Seal 15201600Joint d’huileSello del aceite3

640058572Brass Bushing 52536000Douille en laitonBuje de bronce3

650058573O-Ring 15001800Joint toriqueAro3

660058574Oil Fill Cap 57137400Bouchon de remplissage d'huileCubierta de llenado de aceite2

670058575High Pressure SealJoint haute pressionSello de alta presión3

680058518O-Ring 15665300Joint toriqueAro3

690058519Valve Seat 52068400Siège de soupapeBase de válvula6

700058520Valve Plate Stainless Steel 52068101Plaque porte-soupape en acier inoxydableAcero inoxidable de la placa de la válvula6

710058521Spring Valve 52068300Soupape à ressortVálvula de resorte6

720058522Valve Cage 52068200Cage de soupapeCaja de la válvula6

730058523Pump Head 52030202Tête de pompeCabeza de bomba1

740058524Screw m6 10204100VisTornillo4

750058576O-Ring 15000700Joint toriqueAro1

760058577Washer 12406500Rondelles PlatesArandela, plana1

770058578O-Ring 15061800Joint toriqueAro2

780058525Outlet Extension 57136200Rallonge de refoulementExtensión de salida1

790058526Black Cap 52045100Couvercle noirCubierta negra1

850058652Pin 13500500ChevilleClavija 1

860058527Bearing 16003000RoulementCojinete1

870058653Screw 10801600VisTornillo

880058528O-Ring 15000300Joint toriqueAro1

890000085Chemical injectorChimique injectionQuímico del inyector1

900000086Detergent HoseFlexible à détergentManguera de detergente1

910000087FilterFiltreFiltro1

PRE-START PREPARATION

Before starting the pressure washer, check for loose or

missing parts and for any damage which may have occurred

during shipment.

Handle Installation

Slide handle assembly onto handle supports. Align bolt

holes and install 1/4” x 1 1/4” bolts and 1/4” nyloc nuts and

tighten securely.

START-UP PROCEDURE

1.Make sure water supply is connected and turned on.

2.Release gun safety if locked.

3.To allow air to escape from the hose, squeeze trigger on

the gun until there is a steady stream of water coming

from the nozzle.

4.Remove any dirt or foreign matter from the gun outlet and

the male connector of the wand.

5.Insert the nozzle wand into the gun wand and tighten the

fitting securely.

STARTING THE ENGINE

Primer bulb

1.Check oil and fuel level.

2.Set the engine switch to the “ON” position.

3.Push the primer as necessary.

4.Squeeze trigger on pressure washer to release pressure

while pulling on the engine starter rope with a fast steady

pull. Pressure may otherwise build up making starting the

unit difficult.

HIGH PRESSURE HOSE

Attach the high pressure hose to the fitting located on the

front side of the side panel. Only Coleman® Powermate®

Pressure Washer high pressure hoses should be used.

WATER CONNECTION

Before connecting the inlet hose to the unit, run water

through the garden hose (not supplied) to flush out any foreign

matter. The inlet hose will be connected to the fitting located

on the back of the side panel.

RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Up to 3600

GPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.0

Maximum Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1900psi

Oil Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5oz.

The high pressure nozzle position is intended for clean-

ing. When high pressure is required, grasp collar and slide the

collar and nozzle toward the gun.

NOTE: Make sure the nozzle cover is pulled to the

extreme rear position to lock the nozzle in the high pres-

sure position.

When low pressure is required, grasp and slide the nozzle

cover away from the gun.

The adjustable spray nozzle can adjust spray from fan to

pencil point in both the high and low pressure positions. The

spray is adjusted by turning the nozzle cover.

CAUTION: The pencil point spray adjustment

is very aggressive. We recommend that for most

cleaning applications, a twenty degree (20°)

spray angle be used to avoid damage to the

surface being sprayed.

START-UP PROCEDURE SPECIFICATIONS

HIGH PRESSURE/LOW PRESSURE

ADJUSTABLE SPRAY NOZZLE

OPERATING CONNECTIONS

English

Low Pressure

High Pressure

Pin Point Spray

To decrease angle to a pencil point

spray, turn clockwise.

FanSpray

To increase angle to a fan spray,

turn counterclockwise.

Page is loading ...

4970 Airport Road

P. O. Box 6001

Kearney, NE 68848

1-800-445-1805

1-308-237-2181

Fax 1-308-234-4187

are registered trademarks of The Coleman Company, Inc. used under license.

Powermate ® is a registered trademark of Coleman Powermate, Inc.

sont des marques déposées de The Coleman Company, Inc. utilisées sous licence.

Powermate® est une marque déposée de Coleman Powermate, Inc.

son marcas comerciales registradas de The Coleman Company, Inc. utilizadas bajo licencia.

Powermate ® es una marca comercial registrada de Coleman Powermate, Inc.

Coleman® and

Coleman® et

Coleman® y

Calvin Klein PW0881900, Powermate PMC545008, PW0881801 User manual

Other documents