For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
Introduction
The Model T27327 Bed Extension extends the bed
length of the Model T25920 and T25926 benchtop
lathes to accommodate longer workpieces.
MODEL T27327
22" BED EXTENSION
FOR T25920 & T25926
INSTRUCTION SHEET
COPYRIGHT © JUNE, 2015 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
(FOR MODELS MFD. SINCE 06/15) #JH17496 PRINTED IN CHINA
Installation
1. Thread rubber feet into bottom of bed exten-
sion.
2. Remove (2) M10-1.5 x 12 cap screws secur-
ing retaining plate to tailstock end of lathe
bed.
3. Secure bed extension to lathe bed with both
cap screws removed in previous step, (2)
10mm lock washers, and (2) 10mm flat wash-
ers. Finger-tighten only for now.
A. Bed Extension ............................................ 1
B. Rubber Feet ............................................... 2
C. Flat Washers 10mm ................................... 2
D. Lock Washers 10mm ................................. 2
Inventory (Figure 1)
V1.06.15
Figure 1. Model T27327 inventory.
A
B
DC
4. Center tailstock over bed extension and lathe
(see Figure 2), and tighten clamp handle.
This will align bed extension and lathe bed to
bottom of tailstock.
5. Using a 6mm hex wrench, fully tighten bed
extension cap screws.
6. Loosen tailstock clamp handle, and slide
tailstock over length of bed extension and
lathe bed.
—If tailstock catches where lathe and bed
extension meet, loosen fasteners and
repeat Steps 4–6 until it slides smoothly.
7. Place straightedge over bed extension and
lathe bed to verify they are parallel and
aligned.
Figure 2. Tailstock centered over extension
table and lathe bed (Model T25926 shown).
Bed
Extension
Lathe
Tailstock
Lathe
Bed
Refer to Model T25920 and T25926 manuals for
instructions on operating lathe.
If you need help with your new bed extension, call
our Tech Support at: (570) 546-9663.
— If bed extension tilts down, use a strip of
masking tape along bottom edge of lathe
bed to shim the bed extension up (see
Figure 3), then adjust bed extension rub-
ber feet to level bed surface.
Figure 4. Shimming bed extension down.
Figure 5. Shimming bed extension left.
T27327 Parts Breakdown and List
— If bed extension tilts up, use a strip of
masking tape along top edge of lathe bed
to shim bed extension down (see Figure
4), then adjust rubber feet to level bed sur-
face.
— If bed extension is skewed left or right,
use a vertical strip of masking tape along
corresponding edge of lathe bed to make
bed extension parallel with lathe bed (see
Figure 5).
Figure 3. Shimming bed extension up.
Masking
Tape
Bed
Extension
Lathe
Bed
Extension
Masking
Tape
Lathe
Bed
Extension
Masking
Tape
Lathe
1
2
3
4
*5
6
7
*Note: Part pre-installed on lathe and shown for reference.
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PT27327001 BED EXTENSION 5 PT27327005 CAP SCREW M10-1.5 X 25
2 PT27327002 RETAINING PLATE 6 PT27327006 LOCK WASHER 10MM
3 PT27327003 PHLP HD SCREW M5-.8 X 8 7 PT27327007 FLAT WASHER 10MM
4 PT27327004 RUBBER FOOT M8-1.25 X 15
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.
-
1
-
2
