Titan G-10 Airless Gun Owner's manual

Brand: Titan

Model: G-10 Airless Gun

Category: Paint Sprayer

Type: Owner's manual

Titan G-10 Airless Gun

This high-capacity spray gun is designed for professional use and can handle a wide range of coatings, including latex paints, stains, and primers. It features a durable construction and is easy to use.

The G-10 Airless Gun is equipped with a variety of features that make it ideal for both indoor and outdoor use. These features include:

A high-pressure pump that delivers a consistent, powerful spray
A variety of nozzle tips that allow you to adjust the spray pattern and flow rate
A comfortable grip that reduces fatigue during extended use
A built-in filter that helps to prevent clogs

Titan G-10 Airless Gun

The G-10 Airless Gun is equipped with a variety of features that make it ideal for both indoor and outdoor use. These features include:

A high-pressure pump that delivers a consistent, powerful spray
A variety of nozzle tips that allow you to adjust the spray pattern and flow rate
A comfortable grip that reduces fatigue during extended use
A built-in filter that helps to prevent clogs

Instruction Sheet

2-Finger w/tip 0296236

4-Finger w/tip 0296235

G-10

High Capacity Spray Gun

Important Safety Instructions

Read all safety information before operating the

equipment. Save these instructions.

Indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

To reduce the risks of re or explosion, electrical shock and the

injury to persons, read and understand all instructions included in

this manual. Be familiar with the controls and proper usage of the

equipment.

WARNING: EXPLOSION OR FIRE

Solvent and paint fumes can explode or ignite. Property damage and/

or severe injury can occur.

PREVENTION:

 • Donotsprayammableorcombustiblematerialsnearanopename,

pilotlightsorsourcesofignitionsuchashotobjects,cigarettes,motors,

electrical equipment and electrical appliances. Avoid creating sparks from

connecting and disconnecting power cords.

 • Forunitsintendedforusewithonlywater-basedormineralspirit-type

materialswithaminimumashpointof38ºC(100ºF)—Donotsprayor

cleanwithliquidshavingaashpointoflessthan38ºC(100ºF).Flashpoint

isthetemperatureatwhichauidcanproduceenoughvaportoignite.

 • Useextremecautionwhenusingmaterialswithaashpointbelow100ºF

(38ºC).Refer to your pump manual to determine if these materials can

be sprayed.

 • Paintorsolventowingthroughtheequipmentisabletoresultinstatic

electricity. Static electricity creates a risk of re or explosion in the presence

ofpaintorsolventfumes.Allpartsofthespraysystem,includingthe

pump,hoseassembly,spraygunandobjectsinandaroundthesprayarea

shallbeproperlygroundedtoprotectagainststaticdischargeandsparks.

Useonlyconductiveorgroundedhigh-pressureairlesspaintsprayerhoses

speciedbythemanufacturer.

 • Verifythatallcontainersandcollectionsystemsaregroundedtoprevent

static discharge.

 • Connecttoagroundedoutletandusegroundedextensioncords(electric

modelsonly).Donotusea3to2adapter.

 • Donotuseapaintorsolventcontaininghalogenatedhydrocarbons.Such

aschlorine,bleachmildewcide,methylenechlorideandtrichloroethane.

Theyarenotcompatiblewithaluminum.Contactthecoatingsupplier

aboutcompatibilityofmaterialwithaluminum.

 • Keepsprayareawellventilated.Keepagoodsupplyoffreshair

moving through the area to keep the air within the spray area free from

accumulationofammablevapors.Keeppumpassemblyinwellventilated

area.Donotspraypumpassembly.

 • Donotsmokeinthesprayarea.

 • Donotoperatelightswitches,engines,orsimilarsparkproducingproducts

in the spray area.

 • Keepareacleanandfreeofpaintorsolventcontainers,rags,andother

ammablematerials.

 • Knowthecontentsofthepaintandsolventsbeingsprayed.Readall

MaterialSafetyDataSheets(MSDS)andcontainerlabelsprovidedwiththe

paintsandsolvents.Followthepaintandsolventmanufacture’ssafety

instructions.

 • Placepumpatleast25feet(7.62meters)fromthesprayobjectinawell

ventilatedarea(addmorehoseifnecessary).Flammablevaporsareoften

heavierthanair.Floorareamustbeextremelywellventilated.Thepump

contains arcing parts that emit sparks and can ignite vapors.

 • Plasticcancausestaticsparks.Neverhangplastictoenclosesprayarea.Do

notuseplasticdropclothswhensprayingammablematerial.

 • Fireextinguisherequipmentshallbepresentandworking.

WARNING: INJECTION INJURY

Ahighpressurepaintstreamproducedbythisequipmentcanpierce

theskinandunderlyingtissues,leadingtoseriousinjuryandpossible

amputation. See a physician immediately.

PREVENTION:

 • Donotaimthegunat,orsprayanypersonoranimal.

 • Keephandsandotherbodypartsawayfromthedischarge.Forexample,do

nottrytostopleakswithanypartofthebody.

 • NEVERputyourhandinfrontofthegun.Gloveswillnotprovideprotection

against an injection injury.

 • ALWAYSkeepthetipguardinplacewhilespraying.Thetipguardprovides

someprotectionbutismainlyawarningdevice.

 • Onlyuseanozzletipspeciedbythemanufacturer.

 • Usecautionwhencleaningandchangingnozzletips.Inthecasewherethe

nozzletipclogswhilespraying,ALWAYSlockguntrigger,shutpumpo,

andreleaseallpressurebeforeservicing,cleaningtiporguard,orchanging

tip.Pressurewillnotbereleasedbyturningothemotor.ThePRIME/

SPRAYvalveorpressurebleedvalvemustbeturnedtotheirappropriate

positionstorelievesystempressure.RefertoPRESSURERELIEFPROCEDURE

describedinthepumpmanual.

 • Donotleavetheunitenergizedorunderpressurewhileunattended.

Whentheunitisnotinuse,turnotheunitandrelievethepressurein

accordancewiththemanufacturer’sinstructions.

 • High-pressuresprayisabletoinjecttoxinsintothebodyandcauseserious

bodilyinjury.Intheeventthatinjectionoccurs,seekmedicalattention

immediately.

 • Checkhosesandpartsforsignsofdamage,aleakcaninjectmaterialinto

theskin.Inspecthosebeforeeachuse.Replaceanydamagedhosesor

parts.OnlyuseTITANoriginal-high-pressurehosesinordertoensure

functionality,safetyanddurability.

 • Thissystemiscapableofproducing3600PSI/248Bar.Onlyuse

replacementpartsoraccessoriesthatarespeciedbythemanufacturer

andthatareratedaminimumof3600PSI.Thisincludesspraytips,nozzle

guards,guns,extensions,ttings,andhose.

 • Alwaysengagethetriggerlockwhennotspraying.Verifythetriggerlockis

functioning properly.

 • Verifythatallconnectionsaresecurebeforeoperatingtheunit.

 • Knowhowtostoptheunitandbleedpressurequickly.Bethoroughly

familiarwiththecontrols.Pressurewillnotbereleasedbyturningothe

motor.ThePRIME/SPRAYvalveorpressurebleedvalvemustbeturnedto

theirappropriatepositionstorelievesystempressure.RefertoPRESSURE

RELIEFPROCEDUREdescribedinthepumpmanual.

 • Alwaysremovethespraytipbeforeushingorcleaningthesystem.

NOTE TO PHYSICIAN:

Injection into the skin is a traumatic injury which can lead to possible

amputation. It is important to treat the injury as soon as possible. DO

NOT delay treatment to research toxicity. Toxicity is a concern with some

coatings injected directly into the blood stream. Consultation with a plastic

surgeon or reconstructive hand surgeon may be advisable.

WARNING: GENERAL

Cancausesevereinjuryorpropertydamage.

PREVENTION:

 • Alwayswearappropriategloves,eyeprotection,clothingandarespiratoror

mask when painting.

 • Donotoperateorspraynearchildren.Keepchildrenawayfromequipment

at all times.

 • Donotoverreachorstandonanunstablesupport.Keepeectivefooting

andbalanceatalltimes.

 • Stayalertandwatchwhatyouaredoing.

 • Donotoperatetheunitwhenfatiguedorundertheinuenceofdrugsor

alcohol.

 • Donotkinkorover-bendthehose.Airlesshosecandevelopleaksfrom

wear,kinkingandabuse.Aleakcaninjectmaterialintotheskin.

 • Donotexposethehosetotemperaturesorpressuresinexcessofthose

speciedbymanufacturer.

 • Donotusethehoseasastrengthmembertopullorlifttheequipment.

 • Uselowestpossiblepressuretoushequipment.

 • Followallappropriatelocal,stateandnationalcodesgoverningventilation,

re prevention and operation.

 • TheUnitedStatesGovernmentSafetyStandardshavebeenadopted

undertheOccupationalSafetyandHealthAct(OSHA).Thesestandards,

particularlypart1910oftheGeneralStandardsandpart1926ofthe

ConstructionStandardsshouldbeconsulted.

 • Beforeeachuse,checkallhosesforcuts,leaks,abrasionorbulgingofcover.

Checkfordamageormovementofcouplings.Immediatelyreplacehose

ifanyofthoseconditionsexist.Neverrepairapainthose.Replacewitha

conductivehigh-pressurehose.

 • Donotsprayoutdoorsonwindydays.

 • Alwaysunplugcordfromoutletbeforeworkingonequipment(electric

modelsonly).

0414•FormNo.0286928E

English

 2 ©TitanToolInc.Allrightsreserved.

Using the Gun Trigger Lock

Alwaysengagethegun’striggerlockwhenthegunisnotinuse.

 1. Tolockthetrigger,rotatethetriggerlockforwarduntilitstops.

 2. Tounlockthetrigger,rotatethetriggerlockbackwarduntilitis

vertical.

Trigger locked

(gun will not spray)

igger unlocked

(gun will spray)

Setup

Never attempt to assemble, change, or clean the gun, tip,

or tip guard without first relieving pressure from the spray

system. Follow the “Pressure Relief Procedure” in the

sprayer’s Owner’s Manual.

Always use a tip safety guard for added protection against

injection. Beware that the guard alone will not prevent

injection. Never cut off tip guard! Always engage gun trigger

lock when the gun is not in use. Before servicing equipment,

consult Owner’s Manuals and follow all warnings.

 1. Setupthesprayer.Refertotheinstructionsinthesprayer’sOwner’s

Manual.

 2. Attachagrounded,airlesssprayhosetothematerialinletonthegun.

Usingtwowrenches(oneonthegunandoneonthehose),tighten

securely.

 3. Withthetipandtipguardothegun,startthesprayer.Flushand

preparethespraysystemaccordingtothesprayer’sOwner’sManual.

Inspect the spray system to make sure that all ttings are secure and

that there are no leaks.

Tip Seal

Seal

Tip

Guard

 4. Performthe“PressureRelief

Procedure”describedinthesprayer’s

Owner’sManual.

 5. Usingapenorsimilarobject,insert

thetipsealandsealintotheback

of the tip guard. Press in for nal

adjustment.

 6. Insertthetipintotheslotonthetip

guard.

 7. Threadthetipguardontothegun.

Position the tip guard in the desired

sprayingposition,thentighten

securelybyhand.

NOTE: The arrow on the tip handle should be pointing in the

forward direction for spraying.

Operation

1. Make sure the arrow on the tip handle is pointing in the forward

direction for spraying.

 2. Startthesprayer.Refertotheinstructionsinthesprayer’sOwner’s

Manual.

 3. Adjusttheuidpressureonthesprayeruntilthesprayiscompletely

atomized.Alwayssprayatthelowestpressurenecessarytogetthe

desired results.

NOTE: The spray tip determines the size of spray pattern and

coverage. When more coverage is needed, use a larger tip

instead of increasing uid pressure.

 4. Toclearacloggedtip:

 a. Rotatethetip180ºsothatthearrowonthetiphandleis

pointing opposite the spray direction.

 b. Triggerthegunoncesothatthepressurecanblowtheclogout.

IMPORTANT: Never pull the trigger more than once at time with the tip

in the reverse position.

 c. Continuethisprocedureuntilthetipisclearoftheclog.

Changing a Tip

Tipscanberemovedandreplacedeasilywithoutdisassemblingthegun.

Never attempt to change or clean the tip or tip guard without

first performing the “Pressure Relief Procedure.”

 1. Performthe“PressureReliefProcedure”describedinthesprayer’s

Owner’sManual.

 2. Removethetipfromtheslotonthetipguard.

 3. Insertthenewtipintotheslotonthetipguard.Thearrowonthetip

handleshouldbepointingintheforwarddirectionforspraying.

Removing the Seal and Tip seal

 1. Removethetipfromthetipguard.

 2. Insertthetiphandlethroughthefrontofthetipguard.

 3. Pushthesealandtipsealoutthroughthebackofthetipguard.

Tip Guar

Tip

Tip Seal Retainer

Tip Seal

Identifying Tip Sizes

Toidentifytipsizes,usethefollowingformula.A“517”tipsizewillbeusedin

this example.

Therstdigitmultipliedbytworepresentsthesizeofthespraypatternwhen

spraying12”awayfromtheworksurface:

5x2=10”spraypattern

Thesecondtwodigitsrepresentthediameteroftheoriceonthetip:

17=.017”orice

NOTE: Worn spray tips will adversely aect the spray pattern

and result in reduced production, poor nish, and wasted

material. Replace worn tips immediately.

Cleanup

Maintainingacleangunisimportanttoensuretrouble-freeoperation.Flush

thegunaftereachuseandstoreinadrylocation.Donotleavethegunorany

of its parts in water or solvents.

Special cleanup instructions for use with flammable solvents:

 • Alwaysushspraygunpreferablyoutsideandatleastonehose

length from spray pump.

 • Ifcollectingushedsolventsinaonegallonmetalcontainer,

place it into an empty ve gallon container, then ush solvents.

 • Areamustbefreeofammablevapors.

 • Followallcleanupinstructions.

IMPORTANT: The sprayer, hose, and gun should be cleaned thoroughly

after daily use. Failure to do so permits material to cake, seriously

affecting the performance of the unit.

Always spray at minimum pressure with

the tip and tip guard removed when

using mineral spirits or any other solvent

to clean the sprayer, hose, or gun. Static

electricity buildup may result in a fire or

explosion in the presence of flammable

vapors. Hold the gun firmly against a

metal container while flushing.

©TitanToolInc.Allrightsreserved. 3

Maintenance

Follow all safety precautions as described in the Safety

Precautions section of this manual before proceeding.

NOTE: Refer to the Parts List section in this manual for part

identication.

Replacing/Servicing the Seal Assembly

Ifyourspraygunleaksorspitsatthetipwhenyoureleasethetrigger,the

needleorseatisworn,damaged,ordirtyandmustbereplacedorcleaned.

Never attempt to perform maintenance on the spray gun

without first performing the “Pressure Relief Procedure.”

 1. Disconnecttheuidhosefromthegun.

 2. Removethetipandtipguard.

 3. Withthetriggerdepressed,removethediuserfromthefrontofthe

gun.

 4. Removethelocknut,rearhousing,andretractorpinsfromtherearof

the gun head.

 5. Removethesealassemblyfromthefrontofthegunheadbypushing

orgentlytappingatthebackofthesealassembly.

 6. Soaktheremovedpartsintheappropriatesolventandwipeclean.

 7. Inspectthepartsforwearordamageandusenewpartsduring

reassemblyofthegun,whennecessary.

NOTE: Lubricate all packings and moving parts before

reassembly with a lithium-based grease.

 8. Installthesealassemblyintothefrontofthegunhead.

9. Install the retractor pins into the rear of the gun head. Slide the rear

housing onto the retractor pins and secure in position with the lock

nut.

 10. WIththetriggerdepressed,installthediuserintothefrontofthe

gun head and tighten securely with a wrench.

 11. Performthe“AdjustingtheSealAssembly”proceduredescribed

below.

Adjusting the Seal Assembly

Proper adjustment of the seal assembly is essential to ensure

positive shut-off when the trigger is released.

 1. Tightenthelocknutuntiltherearhousingisushagainstthegun

head.

 2. Unscrewthelocknut3/4ofaturn.

NOTE: To check the adjustment of the seal assembly:

1. Move the gun trigger lock to the locked position.

2. Pull the trigger.

With the trigger lock engaged, there should be 1/32” of

movement between the lock nut and the rear housing

while pulling the trigger.

Replacing/Removing the Filter

 1. Pullthebottomofthetriggerguardforwardsothatitcomesloose

fromthehandleassembly.

 2. Loosenandremovethehandleassemblyfromthegunhead.

 3. Pulltheoldlteroutofthegunhead.

 4. Slidethenewlter,taperedendrst,intothegunhead.

 5. Makesurethehandlesealisinpositionandthreadthehandle

assemblyintothegunheaduntilsecure.

 6. Snapthetriggerguardbackontothehandleassembly.

Gun Filter Chart

Part

Number

Application Filter Type Color of

Filter Body

0089960 Syntheticresin,enamels,clean

varnishes,stains,azures

Extrane red

0089959 Basecoatenamels,primer

enamels,llers,markingpaints,

textured enamels

Fine yellow

0089958 Emulsions,latexpaints,acrylic

paints

Medium white

0089957 Fillerpaints,largeareasurfaces Coarse green

Parts List

Item Part # Description Quantity

 1 0296228 Gunhead ................................................................................1

 2 0296284 Triggerscrew,short ............................................................1

 3 0296285 Triggerassembly,4-ngergun ...................................... 1

 4 0296230 Triggerguard ........................................................................1

 5 0296270 Sealassembly ....................................................................... 1

 6 0296404 Diuser ...................................................................................1

 7 0297045 Seal ...........................................................................................1

 8 662-517 Tipassembly(includesitems7and10) ...................... 1

 9 0289228 Tipguard ...............................................................................1

 10 0297007 Tipseal .................................................................................... 1

 11 9910201 Locknut .................................................................................. 1

 12 0296222 Rearhousing .........................................................................1

 13 0296286 Retractorpin ......................................................................... 2

 14 0296287 Triggerscrew,long .............................................................1

 15 0089958 Filter,medium ...................................................................... 1

 16 0296289 Handleseal ............................................................................ 1

 17 0296342 Handle .....................................................................................1

 18 0296343 Spring ...................................................................................... 1

 19 0347706 Swivel ......................................................................................1

 20 0296291 Triggerassembly,2-ngergun ...................................... 1

 21 0279185 Collarassembly,2-ngergun .........................................1

  0296345 Handleassembly(includesitems17–19)

  0296294 Gunrepairkit(includesitems5,6,and11)

English

Warranty

TitanTool,Inc.,(“Titan”)warrantsthatatthetimeofdeliverytotheoriginalpurchaserforuse(“EndUser”),theequipmentcoveredbythis

warrantyisfreefromdefectsinmaterialandworkmanship.Withtheexceptionofanyspecial,limited,orextendedwarrantypublishedbyTitan,

Titan’sobligationunderthiswarrantyislimitedtoreplacingorrepairingwithoutchargethosepartswhich,toTitan’sreasonablesatisfaction,are

showntobedefectivewithintwelve(12)monthsaftersaletotheEndUser.Thiswarrantyappliesonlywhentheunitisinstalledandoperatedin

accordance with the recommendations and instructions of Titan.

Thiswarrantydoesnotapplyinthecaseofdamageorwearcausedbyabrasion,corrosionormisuse,negligence,accident,faultyinstallation,

substitutionofnon-Titancomponentparts,ortamperingwiththeunitinamannertoimpairnormaloperation.

DefectivepartsaretobereturnedtoanauthorizedTitansales/serviceoutlet.Alltransportationcharges,includingreturntothefactory,if

necessary,aretobeborneandprepaidbytheEndUser.RepairedorreplacedequipmentwillbereturnedtotheEndUsertransportation

prepaid.

THEREISNOOTHEREXPRESSWARRANTY.TITANHEREBYDISCLAIMSANYANDALLIMPLIEDWARRANTIESINCLUDING,BUTNOTLIMITEDTO,

THOSEOFMERCHANTABILITYANDFITNESSFORAPARTICULARPURPOSE,TOTHEEXTENTPERMITTEDBYLAW.THEDURATIONOFANYIMPLIED

WARRANTIESWHICHCANNOTBEDISCLAIMEDISLIMITEDTOTHETIMEPERIODSPECIFIEDINTHEEXPRESSWARRANTY.INNOCASESHALL

TITANLIABILITYEXCEEDTHEAMOUNTOFTHEPURCHASEPRICE.LIABILITYFORCONSEQUENTIAL,INCIDENTALORSPECIALDAMAGESUNDER

ANYANDALLWARRANTIESISEXCLUDEDTOTHEEXTENTPERMITTEDBYLAW.

TITANMAKESNOWARRANTYANDDISCLAIMSALLIMPLIEDWARRANTIESOFMERCHANTABILITYANDFITNESSFORAPARTICULARPURPOSE

WITHRESPECTTOACCESSORIES,EQUIPMENT,MATERIALSORCOMPONENTSSOLDBUTNOTMANUFACTUREDBYTITAN.THOSEITEMSSOLD,

BUTNOTMANUFACTUREDBYTITAN(SUCHASGASENGINES,SWITCHES,HOSES,ETC.)ARESUBJECTTOTHEWARRANTY,IFANY,OFTHEIR

MANUFACTURER.TITANWILLPROVIDETHEPURCHASERWITHREASONABLEASSISTANCEINMAKINGANYCLAIMFORBREACHOFTHESE

WARRANTIES.

United States Sales & Service

1770 Fernbrook Lane

Minneapolis, MN 55447

www.titantool.com

Phone:

Fax:

1-800-526-5362

1-800-528-4826

1770 Fernbrook Lane

Minneapolis, MN 55447

Fax: 1-763-519-3509

International

[email protected]

Titan G-10 Airless Gun Owner's manual

Brand: Titan

Model: G-10 Airless Gun

Category: Paint Sprayer

Type: Owner's manual

Titan G-10 Airless Gun

The G-10 Airless Gun is equipped with a variety of features that make it ideal for both indoor and outdoor use. These features include:

A high-pressure pump that delivers a consistent, powerful spray
A variety of nozzle tips that allow you to adjust the spray pattern and flow rate
A comfortable grip that reduces fatigue during extended use
A built-in filter that helps to prevent clogs

Download PDF

report

Titan G-10 Airless Gun Owner's manual

Titan G-10 Airless Gun Owner's manual

Related papers

Other documents