AVerMedia Technologies EB1304 NET User manual

AVerMedia

®

AVerDiGi EB1304 NET

Operation Manual

www.avermedia.com

www.averdigi.com

FCC NOTICE (Class B)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Federal Communications Commission Statement

NOTE- This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be required to correct the interference at his own

expense.

CAUTION ON MODIFICATIONS

To comply with the limits for the Class B digital device, pursuant to Part 15 of the FCC Rules, this device must

be installed in computer equipment certified to comply with the Class B limits. All cables used to connect the

computer and peripherals must be shielded and grounded. Operation with non-certified computers or

non-shielded cables may result in interference to radio or television reception.

Changes and modifications not expressly approved by the manufacturer could void the user’s authority to

operate this equipment.

European Community Compliance Statement (Class B)

This product is conformity with the protection requirements of EU Council Directives 89/336/EEC

amended by 92/31/EEC on the laws of the Member States relating to electromagnetic compatibility.

Warning - This is a Class B product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures to correct this interference.

DISCLAIMER

No warranty or representation, either expressed or implied, is made with respect to the contents of this

documentation, its quality, performance, merchantability, or fitness for a particular purpose. Information

presented in this documentation has been carefully checked for reliability; however, no responsibility is

assumed for inaccuracies. The information contained in this documentation is subject to change without notice.

In no event will AVerMedia be liable for direct, indirect, special, incidental, or consequential damages arising out

of the use or inability to use this product or documentation, even if advised of the possibility of such damages.

TRADEMARKS

AVerMedia is registered trademarks of AVerMedia TECHNOLOGIES, Inc. IBM PC is a registered trademark of

International Business Machines Corporation. Macintosh is a registered trademark of Apple Computer, Inc.

Microsoft is a registered trademark and Windows is a trademark of Microsoft Corporation. All other products or

corporate names mentioned in this documentation are for identification and explanation purposes only, and

may be trademarks or registered trademarks of their respective owners.

COPYRIGHT

transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means

without the written permission of AVerMedia TECHNOLOGIES, Inc.

The mark of Crossed-out wheeled bin indicates that this product must not be disposed of with your

other household waste. Instead, you need to dispose of the waste equipment by handing it over to

a designated collection point for the recycling of waste electrical and electronic equipment. For

more information about where to drop off your waste equipment for recycling, please contact your

household waste disposal service or the shop where you purchased the product.

Battery Safety Information

- Store the batteries in a cool dry place.

- Do not dispose of used batteries in domestic waste. Dispose of batteries at special collection points or

return to point of sale if applies.

- Remove the batteries during long periods of non-use. Always remove exhausted batteries from the

remote control. Battery leakage and corrosion can damage this remote control, dispose of batteries

safely.

- Do not mix old and new batteries.

- Do not mix different types of batteries: alkaline, standard (carbon-zinc) or rechargeable

(nickel-cadmium).

- Do not dispose of batteries in a fire. The batteries may explode or leak.

- Never short circuit the battery terminals.

-

WARNING

TO REDUCE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE

CAUTION

IF THERE IS ANY DAMAGE, SHORTAGE OR INAPPROPRIATE

ITEM IN THE PACKAGE, PLEASE CONTACT WITH YOUR LOCAL

DEALER. WARRANTY VOID FOR ANY UNAUTHORIZED

PRODUCT MODIFICATION

Table of Contents

Chapter 1

Introduction ......................................................................1

1.1 Package Content........................................................................................ 1

1.2 Features and Specifications ....................................................................... 1

1.3 Front Panel ................................................................................................ 2

1.4 Back Panel................................................................................................. 2

1.5 Setting Up the DVR Unit ............................................................................ 3

1.5.1 Installing the Hard Disk.......................................................................... 3

1.5.2 Connecting Devices............................................................................... 5

1.5.3 Connecting the Sensor/Relay device..................................................... 5

Chapter 2

Operating the EB1304 NET..............................................7

2.1 Familiarizing the Remote Control Buttons.................................................. 7

2.1.1 Using AB Repeat Function..................................................................... 8

2.1.2 Using USB Backup Button..................................................................... 9

2.2 Using the EB1304 NET for the First Time .................................................. 9

2.2.1 Set up the System Date and Time ......................................................... 9

2.3 Surveillance Screen ................................................................................. 10

2.4 Playback the Video .................................................................................. 10

Chapter 3

OSD Navigation Tree......................................................12

3.1 Menu Function ......................................................................................... 13

Chapter 4

Using the USB Playback Console.................................23

4.1 Recommended system requirements....................................................... 23

4.2 Installing the USB Playback Console ....................................................... 23

4.3 Running the USB Playback Application.................................................... 24

4.3.1 To Cut and Save the Portion of the Recorded Video ........................... 26

4.3.2 Playback DVR Recorded File from Hard Disk ..................................... 26

4.3.3 Playback Backup File(*.dvr)................................................................. 22

Chapter 5

Backup Recorded Video File.........................................28

5.1 Recommended system requirements....................................................... 28

5.2 Familiarizing with HDD Backup Application.............................................. 28

5.3 To Backup Recorded Video File............................................................... 29

Chapter 6

ImageVerification ...........................................................31

6.1 To Run the ImageVerification ................................................................... 31

Chapter 7

Video Enhancer..............................................................32

Chapter 8

Using the Remote Programs .........................................34

8.1 Familiarizing the WebCam Buttons .......................................................... 35

8.1.1 To Setup Remote System Setting........................................................ 36

8.2 Familiarizing the Remote Console Buttons .............................................. 43

8.2.1 To Setup Remote Console Setting....................................................... 44

8.3 Using the Remote Playback..................................................................... 45

8.3.1 Familiarizing the Local Playback Buttons ............................................ 46

8.3.2 Familiarizing the Download and Playback Buttons .............................. 48

Appendix A Registering Domain Names............................................................. 49

1

Chapter 1 Introduction

1.1 Package Content

(1) AVerDiGi EB1304 NET unit

(2) Remote Control (batteries included)

(3) Quick Installation Guide

(4) Power Cord

* The power cord varies depending on the standard power outlet of

the country where it is sold.

(5) Power Adapter

(6) DVR accessories (including 4 screws)

(7) Software CD (User Manual included)

1.2 Features and Specifications

 Non-PC stand-alone network digital video recorder

 4 composite video inputs and 1 composite output

 VGA output for LCD or CRT monitor display

 On Screen Display(OSD) control menu

 MPEG4 video compression

 Auto-detect NTSC or PAL video system

 Support Web viewer on Internet Explorer

 Support Central Management System(CMS)

 Support remote console

 Support USB backup to pen drive and external hard disk

 Support network playback and recording simultaneously

 Supports 1 hard disk drive (not included)

 Full-screen resolution:

Display: 720 x 480 (NTSC) / 720 x 576 (PAL)

Recording: 720 x 480 (NTSC) / 720 x 576 (PAL)

 Recording frame rate:

D1 mode: 60fps(NTSC) / 50fps (PAL)

CIF mode: 120 fps (NTSC) / 100fps (PAL)

 Scheduled recording (00:00~23:00 set by hour )

 Search for recorded video files by date/time/event

 Input/Output: 4 sensor inputs and 1 relay output control

 Multiple language operation screens

2

1.3 Front Panel

(1)(2) (3) (4)

Name Function

(1) DVR Power LED

:

Light when the unit is power on

(2) HDD LED

:

Indicate the hard disk running state. Light when the HDD is

running (Read/Write)

(3) IR Sensor

:

Receive the signal from the remote control to operate the unit

(4) USB 2.0 Port

:

Connect to pen drive / external hard disk for backup

1.4 Back Panel

(1) (2) (4) (6) (8) (9) (11) (12)

(3) (5) (7) (10)

Name Function

(1) RJ-45 port :

Ethernet connection port

(2) Audio In :

Input the audio signal from audio output device which it has a

power supply by itself. The audio is embedded with channel 1

(3) Audio Out :

Output the audio signal to a audio out device which it has a power

supply by itself

(4) CH1 :

Input the video camera signal and display it on channel 1

(5) CH2 :

Input the video camera signal and display it on channel 2

(6) CH3 :

Input the video camera signal and display it on channel 3

(7) CH4 :

Input the video camera signal and display it on channel 4

Output the video signal to other vedio output device through BNC

port

(8) Video Out :

The DVR unit support 2 video output ports and you can

only select to output the video either from the VGA OUT or

VIDEO OUT

(9) VGA OUT :

Output the video signal to a CRT or LCD monitor

(10) Sensor In &

Alarm Out

:

Support up to 4 sensor device and 1 relay device (Relay: 1A @

125V AC/30V DC)

(11) TV-VGA Switch :

Switch to select the video output. Make sure to set the video output

before turning on the unit

(12) 12V DC :

Connect the power adapter into this port

3

1.5 Setting Up the DVR Unit

1.5.1 Installing the Hard Disk

The DVR unit allows user to install one hard disk. Before installing the hard disk,

make sure to set the hard disk master jumper setting. Adjust the jumper setting

according to the instructions on the hard disk label.

i

Use 40GB/ 7200RPM IDE interface hard disk or larger is recommended

Follow the illustrated instructions below to install the hard disk:

1. Loosen all screws

2. Push the cover backward and lift

3. Loosen the hard disk rack 4 screws

4. Secure the brackets on the hard disk

4

5. Connect the end of the IDE cable

and the power connector to the hard

disk

6. Secure the hard disk inside the unit

then replace unit cover

7. Push the cover forward

8. Secure the cover

9.

You may now connect all the cables. When the power is connected, the Power

LED light

turns on

5

1.5.2 Connecting Devices

The back panel of the DVR unit, user can connect up to 4 video cameras, 4 sensor

devices, 1 alarm device and output video to a TV or CRT/LCD monitor. Connecting

the unit to a PC, through USB connection, the bundled software enables user to

transfer, playback and segment the video.

Follow the illustration below to make the connection:

Each time user changes the video display output, the power must be

UNPLUGGED and PLUGGED to reset

1.5.3 Connecting the Sensor/Relay device

The Sensor and Alarm ports enable you to connect (4) sensor inputs and (1) relay

outputs. Just connect the external sensor and relay pin directly to the pinhole.

Check the table below and locate which pinhole is assigned to sensor input and

relay output.

6

1.5.3.1 I/O Card Sensor and Relay pinhole allocation:

The signal from the sensor (i.e., infrared sensors, smoke detectors, proximity

sensors, door sensors, etc.) is being transmitted to the unit and this triggers the

system to respond and send signal to relay device (i.e., alarm, telephone etc).

Pin # Definition

1 Sensor 1 positive pole signal

2 Sensor 1 negative pole signal

3 Sensor 2 positive pole signal

4 Sensor 2 negative pole signal

5 Sensor 3 positive pole signal

6 Sensor 3 negative pole signal

7 Sensor 4 positive pole signal

8 Sensor 4 negative pole signal

9 Relay negative pole signal

10 Relay positive pole signal

7

Chapter 2 Operating the EB1304 NET

2.1 Familiarizing the Remote Control Buttons

Use the Remote control to operate the OSD menu on surveillance screen.

0

FN

RIGHTUPLEFT

EB DVR

2 3

5 6

8 97

1

4

▼

▲

REC

A-B

MENUSELECT

ZOOM

-

SPEED

+

SPEED

-

FOCUS

-

ZOOM

+

DOWNFOCUS

+

▲

▼

RM-H6

▼

PTZ

(2)

(1)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

(10)

(11)

(18)

(17)

(12)

(13)

(14)

(15)

(16)

Button Function

(1)

FN

A functional key for multiple DVR system remote control

Switch to Channel 1

(2)

1

As a number key for entering password

Switch to Channel 2

(3)

3

As a number key for entering password

Switch to Channel 3

(4)

7

As a number key for entering password

Switch to Channel 4

(5)

9

As a number key for entering password

Switch to CIF mode

(6)

5

As a number key for entering password

2

4

6

8

(7)

0

As a number key for entering password

(8)

A-B

Set a playing recorded video from A point to B point segment

and repeat playing on surveillance screen(See 2.1.1)

(9)

Pause the playing

(10)

▲

To play the video

8

Button Function

(

11)

▼

Decrease the video playback at the speed of 2x, 4x 8x or 16x

(

12)

▼

Fast play the video playback at the speed of 2x, 4x 8x or 16x

(13)

Stop playing / Stop recording

(14)

USB backup(see 2.1.2)

▼

To move the selection to the left and right

▲

(15)

▼

To go up and down and select the items in the menu list or

change the settings

(16)

To enter the OSD Main menu / Exit from the main menu or sub-menu

display

Make a selection

(17)

Enter sub-menu

(18)

REC

Start video recording

i

The lower parts of buttons are not functional for the DVR system.

2.1.1 Using AB Repeat Function

AB Repeat function allow user to set a video segment from A to B point and play on

the surveillance screen until user stop. User also can backup AB Repeat file to pen

drive or external hard disk (See 2.1.2).

1. Press

▲

(play button) to call out the

SEARCH MODE

menu to find the

recorded video that user wants to

playback.

2. Select

TIME SEARCH

or

EVENT LIST

.

-

TIME SEARCH

(search by date and

time): select the date and time from

where you want to begin the video

playback.

-

EVENT LIST

(search by condition): select from the list.

3. During the playback, press

A-B

to set the A point of video segment. And then,

press

A-B

again to set the B point of video segment. On the surveillance

screen will display “

A-B

” and repeat playing the AB point video segment which

user has set. To cancel AB repeat, press

A-B

again.

A-B

9

USB BAKCUP

YES(SELECT) / NO(MENU)

2.1.2 Using USB Backup Button

User can press button to backup the AB Repeat video file.

1. Set the AB Repeat file (see 2.1.1).

2. Plug in pen drive or external hard disk to DVR

system.

3. During the AB Repeat playback, press

button.

4. And then, press (YES)

to start backup file or

press (NO) to exit backup mode.

i

The DVR system doesn’t support the power for external hard disk.

Therefore, the external hard disk need has power supply by itself.

2.2 Using the EB1304 NET for the First Time

Upon connecting the power, the unit automatically detects the status of the hard

disk. The hard disk must be formatted before user can use it with EB1304 NET. If

you are prompt to format the hard disk, press (select) for

YES

to format the

hard disk and (menu) for

NO

to remain unchanged.

HARD DISKS INFORMATION

VERSION 1 . 3. 03

MASTER HDD

HDD FORMAT YES (SELECT) / NO (MENU)

HDD CHECKING . . .

SIZE 76GB 509MB

2.2.1 Set up the System Date and Time

Before starting record video, adjust the date and time first.

1. Press to call up the OSD menu and then use

▲

and

▼

to go up

and down and select Submenu. And then, press to confirm the selection.

2. In Submenu, select the Date and press again to make a selection. And

then, use

▲

and

▼

o to adjust the date and use

▼

and

▼

buttons

to move the selection to the left and right.

3. To adjust Time, follow the above step 2 and 3.

4. Press to go back to main menu after adjustment.

10

2.3 Surveillance Screen

To know if the channel is being recorded, the “” record symbol would appear

beside the channel number. The (microphone) and (speaker) indicate that

the audio is available. The information below the screen shows the current date

and time, recording mode (record schedule setting), and the percentage of the

used hard disk space.

D1 (A) HDD 29%

D1 mode Screen Preview

CIF(A) HDD 29%

CIF model Preview

When you are in full screen preview, press the following buttons on the remote

control to switch to different channel, or preview all 4 channels:

1

CH1: Camera1

3

CH2: Camera 2

7

CH3: Camera 3

9

CH4: Camera 4

5

QUAD: 4-Channel

2.4 Playback the Video

The DVR system can record and playback video simultaneously. Therefore, user

don’t need to stop recording while playback the video.

1. Press

▼

2. Use the

▲

and

▼

buttons to go up and

down and select TIME SEARCH or EVENT LIST.

Then, press or

▼

to make a selection.

SEARCH METHOD

TIME SEARCH

EVENT LIST

11

TIME SEARCH (search by date and time):

1. Use the

▲

and

▼

buttons and select

SEARCH TIME

. Then press or

▼

again to make the selection.

2. In the

SEARCH TIME

, user may now select the

date and time from where you want to begin the

video playback.

TIME SEARCH

START TIME

END TIME : 2006 / 05 / 05 13 : 08 : 13

: 2006 / 05 / 04 10 : 00 : 01

: 2006 / 05 / 04 10 : 00 : 01SEARCH TIME

HARD DISK :

Use the

▼

and

▼

buttons to move the selection to the left and right. Use the

▲

and

▼

buttons to select the date and time. Then press or

▼

again to make

the selection.

3. To start video playback, the time in second must be set. Use the

▼

buttons to move the

selection to the right most. Use the

▲

and

▼

buttons and select the time in second.

Then press or

▼

.

EVENT LIST (search by event):

1. Use the

▲

and

▼

buttons to select from

the list. Press or

▼

again to make the

selection. User and

to go next page

or back to previous page.

Listed below are the following recording

conditions:

EVENT LIST

S

A

2006 / 05 / 03

13 : 26 : 34

13 : 00 : 01

13 : 26 : 50

13 : 16 : 46

A 2006 / 05 / 03 12 : 00 : 01 13 : 00 : 01

B 2006 / 05 / 03

11 : 48 : 37 12 : 00 : 00

A 2006 / 05 / 03 11 : 30 : 23 11 : 31 : 18

A 2006 / 05 / 03

11 : 29 : 47 11 : 30 : 13

B 2006 / 05 / 03

11 : 28 : 55 11 : 28 : 58

S 2006 / 05 / 03 11 : 28 : 33 11 : 28 : 55

A 2006 / 05 / 03 11 : 25 : 41 11 : 28 : 32

A 2006 / 05 / 03 11 : 23 : 26 11 : 23 : 30

A – Always Recording

It records non-stop and automatically continue recording when interrupted

S – Sensor Recording

It records when the sensor has triggered

M – Motion Recording

It records when any movement has detected

B – Button Recording

It records when the

REC

record button is pressed

2. The “” play symbol would appear beside the channel number when you are previewing in

playback mode.

12

Chapter 3 OSD Navigation Tree

The follow figure is an OSD menu tree map. To call out the OSD menu, press

on the remote control.

RECORD SCHEDULE

13 : 00 - 14 : 00

14 : 00 - 15 : 00

15 : 00 - 16 : 00

18 : 00 - 19 : 00

19 : 00 - 20 : 00

20 : 00 - 21 : 00

21 : 00 - 22 : 00

22 : 00 - 23 : 00

23 : 00 - 00 : 00

17 : 00 - 18 : 00

16 : 00 - 17 : 00

ALWAYS REC

ALWAYS RECALWAYS REC

ALWAYS REC

ALWAYS RECALWAYS REC

ALWAYS REC

ALWAYS RECALWAYS REC

ALWAYS REC

ALWAYS RECALWAYS REC

RECORD SCHEDULE

00 : 00 - 01 : 00

01 : 00 - 02 : 00

02 : 00 - 03 : 00

05 : 00 - 06 : 00

06 : 00 - 07 : 00

07 : 00 - 08 : 00

08 : 00 - 09 : 00

09 : 00 - 10 : 00

10 : 00 - 11 : 00

11 : 00 - 12 : 00

12 : 00 - 13 : 00

04 : 00 - 05 : 00

03 : 00 - 04 : 00

ALWAYS REC

1 2 3 41 2 3 4

D1D

MPEG4

60

GOOD

ENGLISH

MAIN MENU

CAMERA SELECT

RECORD SELECT

RECORD MODE

VIDEO FORMAT

RECORD FRAMERATE

VIDEO QUALITY

RECORD SCHEDULE

SUBMENU

HARD DRIVE SETUP

SENSOR SETUP

MOTION SETUP

NETWORK SETUP

USB BACKUP

LANGUAGE SETUP

2006 / 04 / 20

17 : 54 : 50

ON

OFF

NO

SUBMENU

PASSWORD CHANGE

VIDEO ADJUSTMENT

DATE

TIME

AUTO RECORD

AUTO SCAN

PASSWORD SETUP

AUDIO RECORD

AUDIO MUTE

NTSC

OFF

1

VIDEO SYSTEM

MULTIPLE REMOTE

REMOTE ID

PASSWORD SETUP

SUPERUSER

USER(NETWORK)

1

050

000

024

VIDEO ADJUSTMENT

CAMERA

BRIGHTNESS

CONTRAST

HUE

SATURATION

RESET TO DEFAULT VALUE

OFF

10 SEC

AUTO SCAN

AUTO

CHANNEL-1

CHANNEL-2

CHANNEL-3

CHANNEL-4

NO

HARD DRIVE SETUP

OVERWRITE ENABLED

HD1 SIZE 37 GB 78MB

HD1 USED 16 GB 219MB 21%

HD1 FORMAT

010 SEC

NOT INSTALLED

SENSOR SETUP

SENSOR REC TIME

ALARM OUT TIME

CHANNEL - 1

CHANNEL - 2

CHANNEL - 3

CHANNEL - 4

1 2 3 4

HI

010 SEC

MOTION SETUP

MOTION CAMERA

SENSITIVITIY

MOTION RECORD TIME

1 2 3 4

5005

1

5001

STATIC

NETWORK SETUP

IP MODE

NW ENABLE

VIDEO PORT

UPGRADE PORT

USER

SET NW PASSWORD

1 2 3 4

2006/09/23 17:00:02

73G 89MB

2006/09/26 18:00:00

ISB BACKUP

TIME SET

START :

END :

BACKUP CHANNEL

BACKUP SIZE

BACKUP EXECUTE

PASSWORD SETUP

CURRENT

NEW

CONFIRM

SET NW PASSWORD

CURRENT

NEW

CONFIRM

13

3.1 Menu Function

If the unit is currently recording the video, user may have to stop video recording to

change the settings. Use remote control to navigate in the OSD menu. The red

frame turns yellow when you are making a selection.

OSD MENU Description

1 2 3 4

D1

MPEG4

60

GOOD

ENGLISH

MAIN MENU

CAMERA SELECT

RECORD SELECT

RECORD MODE

VIDEO FORMAT

RECORD FRAMERATE

VIDEO QUALITY

RECORD SCHEDULE

SUBMENU

HARD DRIVE SETUP

SENSOR SETUP

MOTION SETUP

NETWORK SETUP

USB BACKUP

LANGUAGE SETUP

CAMERA SELECT :

Enable/disable the channel number to display the video

on the surveillance screen

RECORD SELECT :

Enable/disable the channel number to record video

i

The channels which could be recorded

should be enabled in the CAMERA SELECT

first.

RECORD MODE :

Select D1/CIF recording mode

Under D1 mode, the video recording is in full screen

resolution and takes turns from one channel to the next

one when Auto Scan enables. Each channel is

recorded only at a maximum frame rate of 15fps. User

can switch to view the video in single full screen or

QUAD screen

Whereas in CIF mode, video recording is at a lower

resolution, but each video is recorded in 30fps/25fps

(NTSC/PAL). User can switch to view the video in

single full screen or QUAD screen

VIDEO FORMAT :

The recorded video is in MPEG4 format

RECORD FRAME RATE :

Set the number of frames per second to be recorded.

Refer to the table below for the available record frame

rate settings. The higher the frame rate is, it uses more

hard disk space

Video Standard

Record Mode

NTSC PAL

D1 60, 20, 4 48, 20, 4

CIF 120, 60, 40, 20, 4

100, 48, 20, 4

VIDEO QUALITY :

Select the video quality setting from BEST, HIGH,

MEDIUM, GOOD, NORMAL or LOW.

BEST – best record quality but less record hours

LOW – longest record hour but quality is ordinary

NORMAL – allows you to record more hours but the

quality of the recorded video is moderate.

LANGUAGE SETUP :

Select from the available languages

14

OSD MENU Description

RECORD SCHEDULE

00 : 00 - 01 : 00

01 : 00 - 02 : 00

02 : 00 - 03 : 00

05 : 00 - 06 : 00

06 : 00 - 07 : 00

07 : 00 - 08 : 00

08 : 00 - 09 : 00

09 : 00 - 10 : 00

10 : 00 - 11 : 00

11 : 00 - 12 : 00

12 : 00 - 13 : 00

04 : 00 - 05 : 00

03 : 00 - 04 : 00

ALWAYS REC

RECORD SCHEDULE:

By default, in 24 hours, the recording schedule is set to

always record every hour. Refer to the table below to

customize the recoding condition

Condition Description

NO REC Disable video recording

ALWAYS REC Record non-stop

MOTION REC

Start recording when any movement is

detected

SENSOR REC

Start recording when the sensor has

triggered

BUTTON REC

Start recording

when the record button is

pressed

2006 / 04 / 20

17 : 54 : 50

ON

OFF

NO

SUBMENU

PASSWORD CHANGE

VIDEO ADJUSTMENT

DATE

TIME

AUTO RECORD

AUTO SCAN

PASSWORD SETUP

AUDIO RECORD

AUDIO MUTE

NTSC

OFF

1

VIDEO SYSTEM

MUTIPLE REMOTE

REMOTE ID

PASSWORD CHANGE :

Set a security combination number. There are two type

of user password – SUPERUSER and USER.

PASSWORD CHANG

SUPERUSER

USER(NETWORK)

Use the number button on the remote control to enter

the password. Or use

▲

and

▼

button to the

select the security combination number. Press

or

▼

button to confirm.

SUPERUSER:

Superuser has the authority of formatting hard disk,

changing system settings, remote monitor the DVR

system and changes the system settings. The factory

default password is 111111.

PASSWORD SETUP

CURRENT

NEW

CONFIRM

USER(NETWORK):

The login account for remote connection through the

internet. User account only can view and playback

recorded video by Web viewer (ex: Internet Explorer),

but no authority to change the DVR system’s setting.

The factory default password is 111111.

Page is loading ...

AVerMedia Technologies EB1304 NET User manual

AVerMedia Technologies EB1304 NET User manual

Related papers

Other documents