2Wire Wall-Mount Filter Install Manual

Brand: 2Wire

Model: Wall-Mount Filter

Type: Install Manual

DSL Filter Installation Guide

For Wall-Mounted Telephones

Usage

• The 2Wire DSL Filter for wall-mounted telephones works with G.lite ADSL, Full-rate G.dmt ADSL, and

home phoneline computer networks (HPNA 1.0 and HPNA 2.0).

• Use this filter with all single-line wall-mounted telephones. Other telephone devices (desktop phone,

analog modem, FAX, or answering machine), require the 2Wire DSL Filter.

• You need one DSL Filter for each telephone device (desktop phone, analog modem, FAX, or answering

machine). If you have several telephone devices connected to each other and are using a single

telephone wall jack, install only one filter, connecting it between the wall jack and the first device in the

series.

• IMPORTANT: Do not connect a 2Wire DSL Filter to an ADSL modem or to a home phoneline network

adapter. The filter blocks access to the phone line for these devices.

Filter installation

Your objective is to install the filter between the original wall

plate and your wall-mounted phone.

1. Lift the telephone from the wall pegs, and disconnect the

phone cord from the wall jack.

2. Connect the phone cord from the back of the 2Wire DSL

Filter into the wall jack, and mount the filter on the wall plate

pegs.

3. Connect the phone cord to the phone jack located on the

front of the mounted 2Wire DSL Filter. If you have a DSL

modem, you can connect it to the phone jack located

at the bottom of the filter.

4. Attach the telephone to the mounting pegs on the

2Wire DSL Filter and your installation is complete.

For more information on using 2Wire DSL Filters, as well

as general DSL and home phoneline (HPNA) information,

visit www.2Wire.com.

DSL Filter Installation Guide - for Wall-Mounted Telephones

2 5100--000260-000 Rev A

Mandatory Disclosures

United States and Canada

United States FCC Part 68 Notice - This equipment complies with Part 68 of the FCC rules. Located on the equipment is a label that

contains, among other information, the FCC registration number and ringer equivalence number (REN). If requested, this information

must be provided to the telephone company.

The REN is used to determine the quantity of devices that may be connected to the telephone line. Excessive RENs on the telephone

line may result in the device not ringing in response to an incoming call. In most, but not all areas, the sum of the RENs should not

exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by the total RENs, contact

the telephone company to determine the maximum REN for the calling area.

The equipment cannot be used on the telephone company-provided coin service. Connection to Party Line Service is subject to State

Tariffs.

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary

discontinuance of service may be required. If advance notice isn’t practical, the telephone company will notify the customer as soon as

possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the

equipment. If this happens, the Telephone Company will provide advance notice in order for you to make the necessary modifications

in order to maintain uninterrupted service.

If trouble is experienced with the equipment, please contact:

2Wire, Inc. http:\\www.2Wire.com 877.347.8680

If the trouble is causing harm to the telephone network, the telephone company may request you to remove the equipment from the

network until the problem in resolved.

This equipment uses the following USOC jacks: RJ11C.

Canada IC CS-02 Notice

1. NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain

telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal

Equipment Technical Requirement document(s). The department does not guarantee the equipment will operate to the user’s

satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local

telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer

should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs of alterations

made by the user of this equipment, or equipment malfunctions, may give the telecommunications company cause to request the

user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and

internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural

areas.

Caution: User should not attempt to make such connections themselves, but should contact the appropriate electric inspection

authority, or electrician, as appropriate.

2. The user manual of analog equipment must contain the equipment’s Ringer Equivalence Number (REN) and an explanation notice

similar to the following: The Ringer Equivalence Number (REN) of this device is 0.2B.

NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number

of terminals allowed to be connected to a telephone interface. The termination of an interface may consist of any combination of

devices subject only to the requirement of the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.

3. The standard connecting arrangement (telephone jack type) for this equipment is CA11A.

2Wire Wall-Mount Filter Install Manual

2Wire Wall-Mount Filter Install Manual

2Wire Wall-Mount Filter Install Manual

Related papers

Other documents