Zenith Concierge H25E35DT Installation And Operating Manual, Warranty

Brand: Zenith

Model: Concierge H25E35DT

Type: Installation And Operating Manual, Warranty

This manual is also suitable for

Concierge H20E35DT

Installation / Operating Guide | Warranty

Model Numbers | H20E35DT | H25E35DT | Concierge

TVs with FM Radio

table of contents

page

RECORD THE MODEL NUMBER

The model and serial number of the Concierge

TV are located

on the back of cabinet. For future reference, we suggest that

you record these numbers here:

MODEL NO.____________________________________

SERIAL NO.____________________________________

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.

REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence

of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code

(U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be

connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation.

Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is:

Zenith Electronics Corporation, 2000 Millbrook Drive, Lincolnshire, IL 60069, USA. Phone: 1-847-941-8000.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Concierge

is a trademark of Zenith Electronics Corporation

2-WIRE COMM WARN

For Customer Support/Service please call:

1-888-865-3026

www.zenith.com

PAGE 3

206-3489-O

1. Read Instructions

All the safety and operating instructions should be read

before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for

future reference.

4. Heed Warnings

All warnings on the product and in the operating instruc-

tions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp

cloth for cleaning.

6. Water and Moisture

Do not use this product near water for example, near a

bath tub, wash bowl, kitchen sink, or laundry tub, in a wet

basement, or near a swimming pool.

7. Accessories, Carts, and Stands

Do not place this product on a slippery or tilted surface, or

on an unstable cart, stand, tripod, bracket, or table. The

product may slide or fall, causing serious injury to a child

or adult, and serious damage to the product. Use only with

a cart, stand, tripod, bracket, or table recommended by the

manufacturer, or sold with the product. Any mounting of

the product should follow the manufacturer’s instructions,

and should use a mounting accessory recommended by the

manufacturer.

8. Transporting Product

A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may

cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product

manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventila-

tion and to ensure reliable operation of the product and to

protect it from overheating, and these openings must not

be blocked or covered. The openings should never be

blocked by placing the product on a bed, sofa, rug, or

other similar surface. This product should not be placed in

a built-in installation such as a bookcase or rack unless

proper ventilation is provided or the manufacturer’s instruc-

tions have been adhered to.

11. Power Sources

This product should be operated only from the type of

power source indicated on the marking label. If you are not

sure of the type of power supply to your home, consult

your product dealer or local power company. For products

intended to operate from battery power, or other sources,

refer to the operating instructions.

12. Power Cord Polarization

This product is equipped with a polarized alternating-cur-

rent power plug (a plug having one blade wider than the

other). This plug will fit into the power outlet only one

way. This is a safety feature. If you are unable to insert the

plug fully into the outlet, try reversing the plug. If the

plug should still fail to fit, contact your electrician to

replace your obsolete outlet. Do not defeat the safety pur-

pose of the polarized plug.

13. Power Cord Protection

Power-supply cords should be routed so that they are not

likely to be walked on or pinched by items placed upon or

against them, paying particular attention to cords at plugs,

convenience receptacles, and the point where they exit

from the product.

Important safeguards for you and your new product

Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential

electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read

and observe the following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this operating guide can help you get many years of enjoyment and safe

operation that are built into your new product.

PORTABLE CART WARNING

(Continued on next page)

IMPORTANT SAFETY INSTRUCTIONS

(Continued from previous page)

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the

product, be sure the antenna or cable system is grounded so

as to provide some protection against voltage surges and

built-up static charges. Article 810 of the National Electrical

Code (U.S.A.), ANSI/ NFPA 70 provides information with

regard to proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an antenna dis-

charge unit, size of grounding conductors, location of

antenna-discharge unit, connection to grounding electrodes,

and requirements for the grounding electrode.

15. Lightning

For added protection for this product (receiver) during a

lightning storm, or when it is left unattended and unused

for long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

16. Power Lines

An outside antenna system should not be located in the

vicinity of overhead power lines or other electric light or

power circuits, or where it can fall into such power lines or

circuits. When installing an outside antenna system,

extreme care should be taken to keep from touching such

power lines or circuits as contact with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as this can

result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through

openings as they may touch dangerous voltage points or

short-out parts that could result in a fire or electric shock.

Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening

or removing covers may expose you to dangerous voltage or

other hazards. Refer all servicing to qualified service person-

nel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing

to qualified service personnel under the following condi-

tions:

a. If the power-supply cord or plug is damaged.

b. If liquid has been spilled, or objects have fallen into the

product.

c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following

the operating instructions. Adjust only those controls that

are covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the product to its normal operation.

e. If the product has been dropped or the cabinet has been

damaged.

f. If the product exhibits a distinct change in performance.

21. Replacement Parts

When replacement parts are required, be sure the service

technician has used replacement parts specified by the man-

ufacturer or have the same characteristics as the original

part. Unauthorized substitutions may result in fire, electric

shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product,

ask the service technician to perform safety checks to deter-

mine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as

recommended by the manufacturer. The product may slide or

fall, causing serious injury to a child or adult and serious

damage to the product.

24. Heat

The product should be situated away from heat sources such

as radiators, heat registers, stoves, or other products

(including amplifiers) that produce heat.

PAGE 4

206-3489-O

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)

Grounding Conductor

(NEC Section 810-21)

Ground Clamps

Power Service Grounding

Electrode System (NEC

Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Example of Grounding According to National Electrical

Code Instructions

NEC - National Electrical Code

IMPORTANT SAFETY INSTRUCTIONS

206-3749

PAGE 5

Table of Contents

Turn to the next page to begin the TV set up

Purchase the Optional Installer’s Remote and Clone Programmer

To preform a normal installation set up, you need an installer’s remote like the LP702, and the LT2000 Quickset II Clone

Programmer - - both are shown and described in later sections. The installer remote allows access to the Installer Menu,

and User menus. The installer remote has Menu, Select, and Adjust keys (Down/Left/Right arrow) keys. The LT2000

Quickset II Clone Programmer is used to duplicate a master TV’s setup and install it on another identical TV. See your

Zenith Dealer.

Installer/Hotel Note:

Pages 45, 46, 47, 48, and 49 contain information and menus which the guest can use to operate the

TV and FM Radio. It is recommended that these five pages be copied and included with the literature

packet that the hotel provides to the guest.

Design and specifications are subject to change without prior notice.

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Important Safety Information . . . . . . . . . . . . . . . . 3 - 4

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 1. Hook Up TV

Hookup Directory . . . . . . . . . . . . . . . . . . . . . . . . . . 6

TV and other Equipment Hookups

Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Cable service . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Antenna with VCR . . . . . . . . . . . . . . . . . . . . . . . 9

Cable service with VCR . . . . . . . . . . . . . . . . . . . 10

External Speaker . . . . . . . . . . . . . . . . . . . . . . . 11

Step 2. Channel Search and Reception Setup . . .

Auto Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

(Select Antenna, or cable service and perform channel

search)

Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . 13

Guest’s Remote Key Functions . . . . . . . . . . . . . . . . . . 14

Installer’s Remote Key Functions . . . . . . . . . . . . . . . . 15

On-Screen Menus Overview . . . . . . . . . . . . . . . . . . . . 16

Other Menus and On-Screen Displays . . . . . . . . . . . . . 17

Selecting Viewing Sources . . . . . . . . . . . . . . . . . . . . 18

Step 3. Customize the TV’s Features

Setup Menu (Start with page 12, Auto Program)

Add/Del/Blank . . . . . . . . . . . . . . . . . . . . . . . . . 19

Channel Labels . . . . . . . . . . . . . . . . . . . . . . . . 20

Clock Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Timer (On/Off Timers Setup) . . . . . . . . . . . . . . . . 22

Captions (Caption/Text) . . . . . . . . . . . . . . . . . . . 23

Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Audio Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Bass, Treble, Balance, Audio Mode,

Front Surround, SoundRite, Audio Preference

Video Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Contrast, Brightness, Color, Tint, Sharpness,

Picture Preference

Installer Parental Control Menu . . . . . . . . . 27 - 28 - 29

Set Up Parental Control

FM Radio

FM Radio Auto Program . . . . . . . . . . . . . . . . . . . . . . 30

FM Radio On-Screen Menus . . . . . . . . . . . . . . . . . . . . 31

FM Radio Audio Menu . . . . . . . . . . . . . . . . . . . . . . . 32

Channel Banks

Managing the Channel Banks . . . . . . . . . . . . 33 - 34 - 35

Installer Menus

Installer Menus . . . . . . . . . . . . . . . . . . . . . 36 - 37 - 38

LT2000 Quickset II Clone Programmer . . . . . . 39 - 40 - 41

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Guest Operation Section (Copy for guest usage)

Guest Remote Control Key Functions . . . . . . . . . . . . . . 45

Guest Parental Control Menu . . . . . . . . . . . . . . . . 46 - 47

Guest Menus and On-Screen Displays . . . . . . . . . . . . . 48

Guest FM Radio Operation/Menus . . . . . . . . . . . . . . . . 49

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 - 51

Warranty for Concierge

Series TVs . . . . . . . . . Back Cover

If you are using an antenna and no other equipment, go to . . . . . . . . . . . . . page 7

If you have cable and no other equipment, go to . . . . . . . . . . . . . . . . . . . page 8

If you are using an antenna and have a VCR, go to . . . . . . . . . . . . . . . . . . page 9

If you have cable and a VCR, go to . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10

If you want to connect a Matrix speaker, go to . . . . . . . . . . . . . . . . . . . . . page 11

206-3489-O

PAGE 6

Basic Hook-Up Directory

This page will direct you to which page to go to for proper hook up of the TV

IMPORTANT!!

Use this page to decide where you need to begin the set up. First, find the line below that best

describes what you want to do, then go to that page number.

Cable TV

Wall Jack

Cable Box

Out

Cable TV

Wall Jack

Cable Box

Out

Antenna only

Cable only

Antenna with VCR

Cable and VCR

External Speaker

Locate the Antenna/Cable jack on the back of the TV.

Connect the antenna wire, according to one of the

diagrams to the right.

Remove the back of the remote and put in two AA

batteries.

Plug in the TV. The TV is designed to operate on stan-

dard current, 120-volt 60 Hertz AC. Do not attempt to

operate it on DC power.

Go to page 12 to Auto Program the TV.

Mini glossary

75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire

sticking through the middle, and it screws onto the threaded jack on the back of your TV.

A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws

on one end and a round opening with a wire sticking out on the other end.

206-3489-O

PAGE 7

Antenna Hook Up

Connect an off-air antenna to the TV

If you have a 75 ohm RF cable, then you don’t need any

adapters!

A 300 to 75 ohm adapter is not included with the Zenith TV.

300 TO 75 OHM

ADAPTER

TV Back

TV Back Connections Panel

(Expanded View)

RF Coaxial Wire

(75ohm)

Antenna

R- AUDIO- L

VIDEO

MATRIX

OUT

ANTENNA

CABLE

M.P.I.

back of

remote

120 V AC

60 Hz

ANTENNA

CABLE

M.P.I.

TV Back

Flat Wire

(300 ohm)

Antenna

300/75 ohm

Adapter

TV Back Connections Panel

(Expanded View)

R- AUDIO- L

VIDEO

MATRIX

OUT

206-3489-O

PAGE 8

Cable Service (CATV) Hook Up

If you’re using a cable box, leave the TV on channel 3

or 4 and use your cable box to change channels.

If you’re using a cable box, Auto Program might only

find the channel your cable service is on (usually

channel 3 or 4). Don’t worry, that’s all you need!

Cable TV

Wall Jack

RF Coaxial Wire

(75ohm)

TV Back

R- AUDIO- L

VIDEO

MATRIX

OUT

ANTENNA

CABLE

M.P.I.

Cable TV

Wall Jack

Cable Box

Out

RF Coaxial Wire

(75ohm)

3 4

output

switch

TV Back

R- AUDIO- L

VIDEO

MATRIX

OUT

ANTENNA

CABLE

M.P.I.

Locate the Antenna/Cable jack on the back of

the TV.

Connect the cable service wire that runs from

the wall, according to one of the diagrams to

the right.

Remove the back of the remote and put in two

AA batteries.

Plug in the TV. Your TV is designed to operate

on standard current, 120-volt 60 Hertz AC. Do

not attempt to operate it on DC power.

Go to page 12 to Auto Program the TV.

back of

remote

120 V AC

60 Hz

Connect cable service to the TV

206-3489-O

PAGE 9

Antenna With VCR Hook Up

Connect an off-air antenna and VCR to the TV

No A/V cables are included with the Zenith TV.

Without A/V cables, most VCRs will not play videocas-

settes in stereo sound.

Flat wire

(300 ohm)

Antenna

300/75 ohm

Adapter

A/V cables

not included

with TV

Out

Audio

Video

3 4

VCR Back

VCR Back AV Panel

output

switch

TV Back Connections Panel

(Expanded View)

R- AUDIO- L

VIDEO

MATRIX

OUT

TV Back

ANTENNA

CABLE

M.P.I.

ANTENNA

CABLE

M.P.I.

A/V cables

not included

with TV

Out

Audio

Video

3 4

VCR Back

VCR Back AV panel

output

switch

TV Back Connections Panel

(Expanded View)

R- AUDIO- L

VIDEO

MATRIX

OUT

TV Back

RF Coaxial Wire

(75ohm)

Antenna

Locate the Antenna/Cable jack on the back of the

VCR.

Connect the antenna wire, according to one of the

diagrams to the right. Make the other connections as

necessary as shown to the right.

Remove the back of the remote, put in two AA bat-

teries.

Plug in the TV. The TV is designed to operate on

standard current, 120-volt 60 Hertz AC. Do not

attempt to operate it on DC power.

Go to page 12 to Auto Program the TV.

back of

remote

120 V AC

60 Hz

PAGE 10

206-3489-O

Cable Service (CATV) With VCR Hook Up

Connect a VCR and Cable service to the TV

Leave the VCR and the television tuned to channel

three and use the cable box to change channels.

No A/V cables are included with your TV. Without

A/V cables, most VCRs will not play videocassettes

in stereo sound.

A/V cables

not included

with TV

Out

R - L

Audio

Video

3 4

VCR Back

VCR Back AV Panel

output

switch

TV Back Connections Panel

(Expanded View)

R- AUDIO- L

VIDEO

MATRIX

OUT

TV Back

Cable TV

Wall Jack

Round Wire (75ohm)

Cable Box

Out

3 4

output

switch

ANTENNA

CABLE

M.P.I.

ANTENNA

CABLE

M.P.I.

Cable TV

Wall Jack

Round Wire (75ohm)

A/V cables

not included

with TV

Out

R - L

Audio

Video

3 4

VCR Back

VCR Back AV Panel

output

switch

TV Back Connections Panel

(Expanded View)

R- AUDIO- L

VIDEO

MATRIX

OUT

TV Back

Locate the Antenna/Cable jack on the back

of the VCR.

Connect the cable service wire, according to

one of the diagrams to the right. As

required, make the other connections as

shown to the right.

Remove the back of the remote, put in two

AA batteries.

Plug in the TV. The TV is designed to operate

on standard current, 120-volt 60 Hertz AC.

Do not attempt to operate it on DC power.

Go to page 12 to Auto Program the TV.

back of

remote

120 V AC

60 Hz

PAGE 11

206-3489-O

External Speaker Hook Up

Locate the Audio In jack on the back of the

speaker.

Connect a standard audio cable from the

Matrix Out jack on the TV, to the Audio In

jack on the external speaker.

A/V cables

not included

with TV

R- AUDIO- L

VIDEO

MATRIX

OUT

Audio In

Speaker back

TV Back Connections Panel

(Expanded View)

TV Back

ANTENNA

CABLE

M.P.I.

Connect an external speaker to the TV

PAGE 12

206-3489-O

Auto Program (Channel Search)

Use Auto Program to specify Antenna or cable service

incoming signal source and automatically store all of the

channels that are found by channel search

With the Installer remote control in hand, press the

POWER key to turn on the TV.

Press MENU repeatedly until the Setup menu appears.

Using SELECT on the remote control, highlight Auto

Program on the screen.

Press the Right or Left ADJ (Adjust) arrow to show the

Auto Program menu.

Using SELECT, choose either Cable TV or Off-Air Antenna

on your screen.

Press the Right or Left ADJ arrow to begin the Channel

Search.

Press ENTER when finished.

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

3/5

AUTO PROGRAM

ADD/DEL/BLNK

CH. LABELS

CLOCK SET

TIMER

CAPTIONS

LANGUAGE

TO PROGRAM

Auto Program finds channels being received by the TV tuner.

Cable will not work unless a cable service is subscribed to.

4/6

Mini glossary

OFF-AIR-ANTENNA If the guest can only view over-the-air broadcasts, select Antenna.

CABLE If you provide cable service to your guests, select Cable.

PAGE 13

206-3489-O

Front Panel Controls

audio

video

captions

vol vol

power

left

right

Press POWER to turn on your TV.

To access the menus press the MENU button on the

control panel. Cycle through the various menus by

pushing MENU repeatedly.

Press the SELECT button repeatedly to highlight the

option you want to modify.

Press either the Right or Left ADJUST button to

modify the option you have chosen.

Press CAPTIONS to turn captions on and off.

The menu will disappear after a few seconds.

Use the front control panel to access the menus or just

operate the TV

Note: Item 10 Key Defeat, in the installer’s menu

allows the installer to:

Set Menu Option 10, Key defeat to “0” - Front panel

controls give access to menus.

Set Menu Option 10, Key defeat to “1” - Menus not

available with front panel controls.

The Front Audio/Video jacks are a direct source connec-

tion. If you have a device plugged into the front Video

jack, you will not be able to change channels until you

have unplugged the front Video jack.

Front panel control menu operation buttons are not

labeled and are not usually available to the user.

You can use Ch to select channels and Vol to set the vol-

ume level regardless of the key defeat setting.

There are three jacks on the front of the TV that make connecting

Audio/Video devices like camcorders very simple.

To use the front jacks as the signal source, simply plug a composite

video cable into the VIDEO jack. The TV will automatically change

its source setting to CAMPORT, as indicated on the channel selec-

tion screen.

Video

Connects the video signals from any piece of

equipment.

Left/Right Audio Used for stereo sound from

various types of equipment.

Typical Front Panel Controls

adjust select menu

captions volume channel power

L audio R

video in

Typical Front Panel Controls

(See descriptions below)

PAGE 14

206-3488-O

Guest Remote Key Functions

FLASHBK (FLASHBACK)

Returns to the last channel viewed.

POWER

Turns TV On or Off

CHANNEL (UP/DOWN)

Chooses next available channel, and the

Video Channel (Audio/Video source).

MUTE

Turns sound Off and On, while the picture

remains.

ENTER

Press to view the

Channel/Time/Audio display or to

remove any on-screen

display or menu.

NUMBER KEYPAD

Used to key-in numbers and select channels

directly: key-in channel numbers and press

ENTER to go to the new channel

TIMER

Press repeatedly to set the TV turn-off

time from 10 minutes up to 4-hours.

Sets AM or PM in the Alarm menu.

VOLUME (LEFT/RIGHT)

Adjusts the sound level.

CHANNEL PREVIEW

Displays the available TV channels, including

access to Guest’s Parental Control menu (if

active). Allows guest to select the Video

source. (Use the Audio/Video jacks on the

back of the TV as the source of the picture

and sound.)

CC (CLOSED CAPTIONING)

Direct access to closed captions.

Press ENTER to exit.

A quick list of the keys on the user remote control and what they do

ALARM

Press to display menu, then follow on-screen

instructions to set a time the TV will turn

itself on.

TIMER ALARM

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

remote control part number

SC692A

124-213-03A

TV/FM

Switches between TV and FM radio

operation

NOTE:

The channel and volume keys can be used by the guest to select and adjust the Parental

Control settings, if the installer activates the Parental Control option in the Installer Menu.

206-3489-O

PAGE 15

Installer Remote Key Functions

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

FLASHBK (FLASHBACK)

Returns to the last channel viewed.

POWER

Turns TV On or Off

CHANNEL (UP/DOWN)

Selects next available channel and the

video channel.

MUTE

Turns sound Off and On, while the picture

remains.

ENTER

Press to view the Channel/Time display or

to remove any on-screen display or menu.

remote control part number

LP702

124-213-04

TIMER

Press repeatedly to select preset TV turn-

off time from 10 minutes up to 4-hours.

Sets AM or PM in the Clock/Alarm menus.

VOLUME (LEFT/RIGHT)

Adjusts the sound level.

CC (CLOSED CAPTIONING)

Direct access to closed captions.

Press ENTER to exit.

A quick list of the keys on the LP702 installer’s remote control and their function

ALARM

Press to go to the Alarm menu. Set a time

for the TV to turn itself on.

MENU/SELECT/ADJ (ADJUST)

Adjusts on-screen menus and options.

Press MENU repeatedly to scroll through

menus. Use SELECT to choose an option

and ADJ (adjust) Left/Right to change

the selected option.

CHANNEL PREVIEW

Gives installer access to the Guest’s

menus. Displays the available TV channels

and hotel guest’s Parental Control menu

(if active). Selects the Video source. (Use

the Audio/Video jacks on the back of the

TV as the source of the picture and

sound.)

TV/FM

Selects TV or Radio operation on TVs

equipped with FM radio.

NUMBER KEYPAD

Used to key-in numbers and select chan-

nels directly: key-in channel numbers and

press ENTER to go to the new channel

PAGE 16

206-3749

On-Screen Menus Overview

ON-SCREEN MENUS

SETUP MENU Adjusts the basic operational features of the TV

Auto Program 12 Automatically finds and stores active channels to select with Channel Up/Down.

Add/Del/Blnk 19 Manually picks and chooses which active channels will appear when using Channel Up/Down

Channel Labels 20 Labels the channels with their network names (ABC, CBS, HBO, etc.).

Clock Set 21 Sets the time.

Timer 22 Sets times for the TV to turn itself on and off each day.

Captions 23 Chooses the captioning or text option.

Language 24 Picks the language the on-screen menus will appear in.

AUDIO MENU 25 Customizes the sound. Options are:

Bass, Treble, Balance, Audio Mode, Front Surround, SoundRite, Audio Preference.

VIDEO MENU 26 Adjusts the picture appearance settings. The options are: Contrast, Brightness, Color,

Tint, Sharpness, Picture Preference.

PARENTAL 27/46 Allows installer/user to block program content for up to 12 hours, with the use of a password.

CONTROL MENU

17 OTHER MENUS AND ON-SCREEN DISPLAYS

Channel/Time Shows the current time, channel (or video source), type of incoming audio signal, and XDS* data if available..

Alarm Sets the wake-up time.

Sleep Timer Sets the time the TV will turn off.

Volume Shows current sound level.

Captions Use to select Caption/Text options.

Ch Preview Displays the available channels and menus list.

Channel Bank Shows currently selected channel bank.

FM RADIO MENUS

FM Auto Program 30 Automatically finds and stores FM radio stations to scroll through with Channel Up/Down.

FM Radio Menus 31 Adjusts the operational features of the FM radio

FM Audio Menu 32 Adjusts the FM radio audio features.

Installer Menus

Service Menu 36 Makes adjustments to the TV’s operational features.

*XDS (Extended Data Service) Additional program information provided at the discretion of the

broadcaster. May include: title of broadcast, elapsed time, and time remaining on program.

Descriptions of the menus and on-screen displays available to the installer

Menu Name Page Description

PAGE 17

206-3488-A

Other Menus & On-Screen Displays

Ch 25 - PBS

7:15

OLD TIME MOVIES

LENGTH 01:00 TIME LEFT 00:36

Rating:

TV-14

Channel/Time/Audio/XDS Display

Press ENTER. Shows selected chan-

nel or source, current time if the

clock has been set, incoming audio

signal, and XDS info, if provided.

Sleep Timer Menu

Press TIMER. Sets the time to auto-

matically turn the TV off and shows

remaining time before TV turnoff.

Volume Display

Press VOLUME. Shows currently

selected sound setting.

Alarm Menu

Press ALARM.

TV Mode: Sets a time the TV will

turn itself on.

FM Mode: Sets a time the FM radio

will turn itself on.

VOLUME•

Press the remote keys indicated below to access these menus and displays

CHANNEL BANK

BANK 3

CAPTION 1 IS ON

Ch Preview Menu

Press CH PREVIEW. Displays list of

the available TV Channels, Guest

Parental Control menu (if active)

and Video Channel access. Use

CHANNEL Up/Down to select a

channel, or menu, then ENTER to go

to selected channel or menu.

Closed Captions Menu

Press CC. Turns selected option on

or off. See Caption/Text page to

select options.

Channel Banks Menu

Press SOURCE/BANK on an Installer

remote equipped with those keys.

Accesses the Channel Banks menus:

Bank 1, Bank 2, Bank 3, Bank 4.

CHANNEL PREVIEW•

5 - - - -

9 - - - -

20 - - - -

32 - - - -

44 - - - -

AUX - - - -

CC FOR PARENTAL CONTROL

CH TO SELECT, ENTER TO QUIT

PAGE 18

Selecting Viewing Sources

Make direct connections, or

use the Ch Preview menu to

choose the available picture

and sound sources: either

tunable channels or the AUX

Source to appear on the TV

screen

A direct source connection overrides all other sources. The front

Video In jack is a direct source connection. If you have a device

connected to this jack, you will not be able to change channels

until you have disconnected the device.

Direct Source Selection

Camport

Plug a video cable into the front Video input jack and the TV automati-

cally switches to that input source.

Notes:

• Selectable viewing sources vary depending on the installation

setup for Auto Sense sources in the Service menu.

• Auto Sense sources appear on the TV screen automatically when

they are connected.

Mini glossary

SOURCE Input(s) providing the picture and sound to the TV.

AUTO SENSE SOURCE Input(s) that the TV automatically switches to when connected.

Ch Preview Menu

In addition to available channels

tuning, the CH PREVIEW menu is

used to access the Video Channel

(AUX Source input on TV back).

CHANNEL PREVIEW•

5 - - - -

9 - - - -

20 - - - -

32 - - - -

44 - - - -

AUX - - - -

CC FOR PARENTAL CONTROL

CH TO SELECT, ENTER TO QUIT

AUDIO/VIDEO OUT

R-AUDIO-L

AUDIO/VIDEO OUT

VIDEO

R-AUDIO-L

Video In

L- Audio - R

Camcorder

VCR

Audio/Video

Devices

VIDEO

Video In

L- Audio - R

TV Back

R- AUDIO- L

VIDEO

MATRIX

OUT

ANTENNA

CABLE

M.P.I.

206-3749

PAGE 19

206-3749

Fine-tune the guest’s channel selection list

Setting Add/Delete/Blank

Press the MENU key on the Installer’s remote so the Setup menu

appears.

Press SELECT repeatedly to highlight the Add/Del/Blnk option.

Using either the NUMBER keypad and ENTER or the Channel

Up/Down arrow on the remote, select a channel.

(If adding a deleted channel, you will need to use the NUMBER

keypad and ENTER.)

Using the Right/Left ADJ arrow, pick whether that channel is

Added, Deleted, or Blank.

To continue, select another channel and repeat Step 3. When

you are finished, press ENTER to remove menu.

Adding Aux, VCR 3, VCR 4, or FM to the Channel

Preview List

Go to the Setup menu, select the Add/Del/Blnk option. Use

Channel Up/Down to select the option and choose Added.

Note: If the option was turned off in the Service menu, you will

have to reinstate it before it can appear as an option in the

Channel Preview list.

Note: You can elect to Add, Delete or Blank: VCR 3, VCR 4, and

Aux. FM can be Added or Deleted, but not Blanked.

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

CH 44 ADDED

TIMER

3/5

If you delete a channel, it isn’t gone for good. Just select it using the

NUMBER keypad on the remote, or add it later.

Mini glossary

ADD Adds new channels to the list that the guest can scroll through when using the remote.

DELETE Removes channels for one reason or another from the list that the guest can scroll through.

BLANK Removes the video signal from a channel so the guest will only receive the audio signal.

PAGE 20

206-3600

Channel Labels

AUTO PROGRAM

ADD/DEL/BLNK

CH. LABELS

CLOCK SET

TIMER

CAPTIONS

LANGUAGE

CH 32 ABC

SETUP MENU

Overview

Channel Labels help the user identify the channel or network being viewed.

In the Setup menu with the CH LABELS option highlighted, use the Adjust

Left/Right arrow to scroll through the available channel labels, such as,

A & E, AMC, ESPN, HBO, etc. These are a series of alphabetically organized

preset labels from which you can choose the more common networks. Use any

of these or create custom labels.

- - - - , The 4 dashes will allow a channel label to appear; if one is provided

by XDS. (Extended data service)

NONE, prevents any channel label from appearing.

LAB 1, thru LAB 20, are the 20 programmable labels.

The 20 programmable labels can be customized for your needs.

Each programmable label has 5 characters spaces available.

To Program a Channel Label

First select a channel using the NUMBER keypad and ENTER or the Channel

Up/Down arrow, on the Installer’s remote control.

(To select a deleted channel, use the NUMBER keypad and ENTER.)

To program a channel label, go to the Setup menu and select CH LABELS.

Press the Right/Left ADJ (Adjust) arrow to scroll the available preset labels.

Scroll past - - - -, scroll past NONE, to go to the first programmable label

slot, LAB 1. Notice that the label appears with the title LAB 1, and is also on

a dark background; which will distinguish it from the preset labels.

Operating the Menu

Use Volume Up/Down to select the first letter.

Press MUTE to clear the label if necessary.

Use Channel Up/Down to change the character to one of the 255 characters

available. (A blank letter space is available if required, after the “!” symbol.)

Adjust Left/Right Switches to the next label.

- - moves to the next or previous

label.

Volume Up/Down Selects character spaces

- - moves to the next or previous

character space.

Channel Up/Down Scrolls through the available

characters.

ENTER Accepts the channel label and

removes the menu.

MUTE Removes current label,

- - if first character space is selected.

TIMER

CH PREVIEW

ENTER

POWER

FLSHBK

MUTE

VOL

UME

CHANNEL

TV/FM

ALARM

ADJ

SELECT

Page is loading ...

Zenith Concierge H25E35DT Installation And Operating Manual, Warranty

Brand: Zenith

Model: Concierge H25E35DT

Type: Installation And Operating Manual, Warranty

This manual is also suitable for

Concierge H20E35DT

Download PDF

report

in other languages

italiano: Zenith Concierge H25E35DT

Zenith Concierge H25E35DT Installation And Operating Manual, Warranty

This manual is also suitable for

Zenith Concierge H25E35DT Installation And Operating Manual, Warranty

in other languages

Related papers

Other documents