Atlantis Linea Quattro Series Fitting Instructions

Brand: Atlantis

Model: Linea Quattro Series

Type: Fitting Instructions

BASE AND WASTE FITTING INSTRUCTIONS

BFK-EC-2015

EASY CLEAN WASTE FITTING

Included in this package:

Other equipment required

1 x

Waste fitting – 40mm Easy Clean



Broom

1 x

MB hairgrille



Accurate level

1 x

Waste installation key



Adhesive application / caulking gun

2 x

Sturdi Bond construction adhesive

 

Pozi screwdriver

1 x

White NG silicone



Tape measure

1 x

Quick Start Guide



Levelling compound and associated equipment

(only required for shower base being installed

into a concrete recess)

1 x

Base fitting instructions (this booklet)



The installation process requires the waste fitting to be installed at the same time as the base.

Atlantis recommends this is undertaken by a qualified plumber and carpenter.

Atlantis showers are supplied with Sturdibond to adhere the base to the floor substrate. It is

recommended that Gorilla Grip is used if the temperature drops below 5 degrees.

FLOOR PREPARATION – STEP ENTRY on any floor type

1. Sweep floor free of dust

2. Provide a hole for the waste fitting to a minimum size of 150mm x

200mm, FIGURE 1, in the correct position to suit the shower base.

3. Dry fit the shower base onto the flooring to ensure it is able to be

installed level. The top of the glazing channel(s) and top edges of the

upstands must be level. The floor of the shower base must slope

towards the drain.

FIGURE 1

FLOOR PREPARATION – Timber Recess – Level Entry

1. Measure and mark the floor recess 5mm larger than the overall shower base size.

2. Provide a hole for the waste fitting to a minimum size of 150mm x 200mm, FIGURE 1, in the correct position to

suit the shower base supplied.

3. Cut and remove floorboards. Refer to the recess depth guide chart at the end of these instructions, for a guide

of the recess depth required, and trim joists to the correct level, if required. Apply extra blocking around the

perimeter of the recess and between existing floor joists. Attach trimmers beside joists, fit full flooring in

between and flush with the top of the joists. (excess flooring in diagram)

Atlantis recommends that the shower base is on site to verify the recess depth details.

4. Dry fit the shower base

into the recess to ensure

it is able to be installed

level. The top of the

glazing channel(s) and

top edges of the

upstands must be level.

The floor of the shower

base must slope

towards the drain.

FLOOR PREPARATION – Concrete Recess – Level Entry

1. Create a recess in the concrete slab 5mm larger than the overall shower base size. The recess should be a

minimum of 50mm deep. Refer to recess depth guide chart at the end of these instructions.

2. Provide a hole for the waste fitting to a minimum size of 150mm x 200mm, FIGURE 1 in the correct position to

suit the shower base supplied.

3. Use levelling compound to create a suitably deep level platform, in the recess, for the shower base.

Please refer to the recess depth guide chart at the end of these instructions for a recess depth guide. Atlantis

recommends that the shower base is on site to verify the recess depth details.

STEP ENTRY

TIMBER RECESS

CONCRETE RECESS

4. Once the levelling

compound has set, dry fit

the shower base into to

recess to ensure it is able

to be installed level. The

top of the glazing

channel(s) and top edges

of the upstands must be

level. The shower base

must slope towards the

drain.

WASTE PREPARATION

5. Separate the components of the waste into:

- A. the inner ring and waste cup

- B. the waste body and body seal

6. Connect the waste body to the pipework, FIGURE 2, ensuring that the body seal is in the correct position and

25mm below the floor level, as in FIGURE 2 and 3

FIGURE 2

FIGURE 3

BASE INSTALLATION

7. Clear the recess or floor of all debris and dust

8. Apply supplied construction adhesive liberally to the webbed support rings, the shower base perimeter and the

length of the underside of the channel drain.

9. Install base in final position, ensuring that is it level (as per instruction # 4)

10. The inside face of the upstand must be close to flush with the inside face of the wall board.

11. Screw the upstand of the shower base back to the extra nogging.

12. Allow suitable time for the base adhesive to cure. Keep the shower base surface free from dust and dirt prior to

the application of your base interlayer/waterproofing/tiles to the base.

WASTE CONNECTION

13. Insert the inner ring through the waste outlet in the shower base and screw the inner ring into the waste body.

Hand tighten using the installation key.

14. Place the waste cup and easy clean component (not pictured) into position within the inner ring.

BASE TO FLOOR CONNECTION ANGLE – TIMBER FLOOR ONLY

The Floor Connection angle is supplied as an optional way to create a secure connection between the shower base and

bathroom flooring. To attach the angle, apply silicone. Ensure corners and joints are well sealed. Take into

consideration: under-tile heating, tile underlay and tile thickness before installing the floor connection angle.

Refer to the “Floor Preparation – Timber Recess” instruction and look at the base profile diagram to see the “Floor

connection angle” in place.

IMPORTANT NOTES

- The wall glazing channels must be fitted to the wall after

waterproofing, prior to tiling.

- When tiling a shower base that is 1100mm or larger, the

shower floor tile surface should be a minimum of 6mm

below the top edge of the base glazing channel. Refer to

figure 4.

THIS IS ESPECIALLY IMPORTANT WHEN SLIDING DOOR

SCREENS ARE BEING FITTED – for door clearance.

- Recess depths noted are a guide only. The shower base

should be used to verify the recess required.

FIGURE 4

Linea Quattro - RECESS DEPTH GUIDE CHECK ACTUAL BASE DEPTH ON SITE

3-WALL SHOWERS

3-WALL SHOWERS - CONTINUED

Size

Base Name /

Drain Position

Recess

depth guide

Size

Base Name /

Drain Position

Recess

depth guide

900 x 800

Prague

Back

28mm

900 x 1200

Austin

Back

36mm

1000 x 800

Dallas

Back

28mm

900 x 1400

Lima

Back

38mm

1100 x 800

Bejing

Back

28mm

900 x 1600

Tuscany

Back

42mm

1200 x 800

Stockholm

Back

28mm

900 x 1800

Memphis

Back

44mm

1300 x 800

Lincoln

Back

28mm

1000 x 1200

Portland

Back

36mm

1400 x 800

Moscow

Back

28mm

1000 x 1400

Anchorage

Back

38mm

1500 x 800

Washington

Back

28mm

1000 x 1600

Brussels

Back

42mm

1600 x 800

Budapest

Back

28mm

1000 x 1800

Omaha

Back

44mm

1700 x 800

Amsterdam

Back

28mm

1200 x 1400

Cardiff

Back

38mm

1800 x 800

Copenhagen

Back

28mm

1200 x 1600

Cairo

Back

42mm

1900 x 800

Havana

Back

28mm

1200 x 1800

Munich

Back

44mm

2000 x 800

Seoul

Back

28mm

900 x 900

Rome

Back

28mm

3.5-WALL SHOWERS

1000 x 900

Turin

LH or RH

28mm

Size

Base Name /

Drain Position

Recess

depth guide

Back

1400 x 1000

Nagoya

LH or RH

32mm

1100 x 900

Zurich

Back

34mm

1500 x 1000

Edmonton

LH or RH

34mm

1200 x 900

Berlin

LH or RH

36mm

1600 x 1000

Orlando

LH or RH

36mm

Back

34mm

1800 x 1000

Honolulu

LH or RH

38mm

1300 x 900

Vienna

Back

34mm

1400 x 900

Santiago

LH or RH

38mm

2-WALL SHOWERS

Back

34mm

Size

Base Name /

Drain Position

Recess

depth guide

1500 x 900

Barcelona

LH or RH

40mm

1200 x 800

Liverpool

Back

34mm

Back

34mm

1400 x 800

Oxford

Back

34mm

1600 x 900

Ottawa

LH or RH

42mm

900 x 900

Dublin

LH or RH

28mm

Back

34mm

1000 x 900

Boston

LH or RH

28mm

1700 x 900

Phoenix

Back

34mm

1100 x 900

Rio

LH or RH

34mm

1800 x 900

Tokyo

LH or RH

44mm

1200 x 900

Milan

LH or RH

36mm

Back

34mm

Back

34mm

1900 x 900

Oslo

Back

34mm

1300 x 900

Geneva

LH or RH

38mm

2000 x 900

Singapore

LH or RH

46mm

1400 x 900

Paris

LH or RH

38mm

Back

34mm

1500 x 900

Sofia

LH or RH

40mm

1000 x 1000

Madrid

LH or RH

28mm

Back

34mm

Back

1600 x 900

Kansas

LH or RH

42mm

1100 x 1000

Glasgow

Back

34mm

Back

34mm

1200 x 1000

Toronto

LH or RH

36mm

1800 x 900

Toledo

LH or RH

44mm

Back

34mm

Back

34mm

1300 x 1000

Edinburgh

Back

34mm

1000 x 1000

Miami

LH or RH

28mm

1400 x 1000

Lisbon

LH or RH

38mm

1200 x 1000

Shanghai

LH or RH

36mm

Back

34mm

1400 x 1000

Vancouver

LH or RH

38mm

1500 x 1000

Helsinki

LH or RH

40mm

1500 x 1000

Taipei

LH or RH

40mm

Back

34mm

Back

34mm

1600 x 1000

Chicago

LH or RH

42mm

1600 x 1000

Cleveland

LH or RH

42mm

Back

34mm

Back

34mm

1700 x 1000

Dubai

Back

34mm

1800 x 1000

Richmond

LH or RH

44mm

1800 x 1000

Seattle

LH or RH

44mm

Back

34mm

Back

34mm

1200 x 1200

Detroit

LH or RH

36mm

1900 x 1000

Houston

Back

34mm

2000 x 1000

London

LH or RH

46mm

Angle Front 1000 x 1000

Athens

28mm

Back

34mm

Curved Front 1000 x 1000

Denver

28mm

Atlantis Linea Quattro Series Fitting Instructions

Atlantis Linea Quattro Series Fitting Instructions

Atlantis Linea Quattro Series Fitting Instructions

Other documents