IMPORTANT: PLEASE READ PRIOR TO INSTALLATION
The seat should be inspected on receipt & any defects should be reported
immediately. Failure to do so could affect your guarantee.
The wall / floor to which the seat will be installed must be flat & capable of
bearing the load.
Non-corrosive wall fixings should be used to fix the seat to the wall,
not supplied.
Installation must be undertaken by a qualified tradesman using
suitable fixings for the walls substrate.
Prior to use, a practical check must be undertaken to ensure the seat
is supported correctly & the legs are in the vertical position.
We recommend regular cleaning & inspection of this seat to maintain
its integrity & functionality.
Please retain a copy of this instruction & operating guide for future
reference.
built-in independence
CLS Shower Seat
Fitting & Operating Instructions
For technical assistance with your installation or any other technical help please call: 0845 402 9924
Description Part Reference
CLS Shower Seat - Grey 07SS07G
CLS Shower Seat - Grey & Short Leg 07SS07G-Short
CLS Shower Seat - Blue 07SS07B
CLS Shower Seat - Blue & Short Leg 07SS07B-Short
built-in independence
Contour Showers, Siddorn Street, Winsford, Cheshire CW7 2BA
Telephone: 01606 592586 Fax: 01606 861260
Email: sales@contour-showers.co.uk Website: www.contour-showers.co.uk
ISSUE 1 JULY 2019
IMPORTANT: RAISING & LOWERING THE SEAT
Low the seat by pulling the horizontal leg crossbar downwards.
The legs will automatically fold into the vertical position.
When not in use, lift the seat base upwards & the legs will fold
back into & remain in the vertical position.
DO NOT ATTEMPT to raise & lower the seat by any other method
as this may cause permanent damage to the folding mechanism.
DO NOT use the seat other than for the purpose which it is designed for.
NEVER attempt to alter the seats wall bracket or fixing holes as this
could affect the integrity of the shower seat. This WILL void your
guarantee.
DO NOT adjust the leg height after the seat has been fixed to the wall,
this may make the seat unsafe for the user.
DO NOT unscrew adjustable grey foot by any more than 15mm.
ENSURE no body parts are between or under the seats folding
mechanism whilst operating.
ENSURE the operation instruction label on the seats crossbar is
adhered too.
NEVER lean on the seat for support when folded up against the wall.
FAILURE to install / use this seat as described in these instructions
will invalidate the guarantee & may affect the seats safety.
TESTING Check the movement of the seat once installed
by raising the seat from the down to the up position.
Check that there are no obstructions.
Check the movement of the seat is smooth and unhindered.
Check the seat legs are sitting evenly.
Check the seat legs stay in the up positon when not in use, if
they fall down or, move forward on their own, then adjust the
tension of the seat by tightening the 2 nuts & bolts which hold
the seat frame to the back frame.
CLEANING
It is important that you only clean your shower seat using a non-abrasive
cleaner or mild detergent with a soft cloth. Avoid using lime scale remover.
• Abrasive cleaners e.g. AJAX and/or cleaning pads will damage your seat beyond repair.
• Clean the seat back with a mild detergent and soft cloth with a warm water solution.
• Do not exceed 50ºC when cleaning as this will permanently damage the plastic.
• Under no circumstances place any component into a dishwasher to clean as this will
permanently distort & damage the product beyond repair.
• Regular daily cleaning will reduce the build up of lime scale on your shower seat
• Also check that the cleaner you intend to use is suitable for cellular moulded foam.
DETACHABLE BACK REST
Contour Showers, Siddorn Street, Winsford, Cheshire CW7 2BA
Telephone: 01606 592586 Fax: 01606 861260
Email: sales@contour-showers.co.uk Website: www.contour-showers.co.uk
Fitting & Operating Instructions
1. 1. DETACHABLE BACK REST
2. FIXING THE SEAT TO THE WALL
SHOWER SEAT INSTALLATION
• Choose a suitable fixing for the wall substrate. Fixings are not supplied to allow you the choice to select the correct fixing type for each installation.
• Offer the seat up to the wall at the desired height. At this stage you should make adjustment to the seats extension legs before fixing to the wall.
• Remove the grey ‘e’ clip from the leg & slide the extension leg to the desired height, ensuring that you do not exceed the last hole of the leg.
• Re-insert the ‘e’ clip locating it fully through both the frame & extension leg securely. Repeat for the other leg, ensuring both legs are at the same height.
1. DETACHABLE BACK REST / PADDED SEAT
• Remove the plastic back rest. First undo with an allen key, supplied, the screws located at the bottom rear left & right hand side of the back rest.
• Gently pull the bottom of the back rest approximately 1 inch towards you & push the backrest up until it comes free from the frame.
• Should you require to remove the padded sections from the seat or back rest, gently push the padded tail sections out from the slots & carefully ease off.
• DO NOT pull at the padded sections as this may result in irrepairable damage.
• To re-attach, follow the above details in reverse ensuring that the white screw ports on the reverse of the back rest engage into the holes for the allen screws.
2. FIX SHOWER SEAT TO THE WALL
• Offer the seat up to the wall, check the seat is level horizontally & that the legs are set at the same ‘e’ clip height.
• Mark holes through the wall brackets & back support lug. Pilot drill 9 x holes with a suitable masonry drill & fix securely to the wall with 9 x suitable fixings.
• Secure the wall bracket & back support lug to the wall ensuring every fixing point is used & the seats legs are in the vertical position.
• Apply silicone sealant around the fixing bracket edge(s) to ensure water does not penetrate behind as this may cause damage to the infrastructure of the wall.
• Carefully re-attach the seats back rest, sliding it onto the frame as detailed above.
3. FINE ADJUSTMENT OF EXTENSION LEGS:
• Twist the foot clockwise until you reach the desired height. Do not adjust anymore than
15mm as this may make the seat unsafe for the user.
• Secure in position by twisting the locking nut on the threaded in the opposite direction until
it reaches the underside of the leg.
4. DETACHABLE LUMBER SUPPORT
• Unique detachable lumber support can be re-positioned for individual user comfort.
• To re-position carefully pull the sides of the detachable section away from the back rest.
• Place the tails in-line with the chosen slots in the back rest & push firmly in to position.
• The lumber support is universal & can be rotated by 180º to achieve the desired comfort level.
• To remove the padded back or seat sections for cleaning, carefully pull from the sides in the
same manner as described above.
3. LEG ADJUSTMENT
4. DETACHABLE LUMBER SUPPORT
DETACHABLE LUMBER SUPPORT
This equipment must be installed by a
competent installer.
built-in independence
Fine leg
adjustment
Grey
‘e’ clip
/
